From owner-freebsd-questions Thu May 25 21:57:33 2000 Delivered-To: freebsd-questions@freebsd.org Received: from web2.sea.nwserv.com (web2.sea.nwserv.com [216.145.16.2]) by hub.freebsd.org (Postfix) with ESMTP id AE37137B570 for ; Thu, 25 May 2000 21:57:30 -0700 (PDT) (envelope-from jim@freeze.org) Received: from localhost (jfreeze@localhost) by web2.sea.nwserv.com (8.9.3/8.9.2) with ESMTP id VAA77087; Thu, 25 May 2000 21:57:04 -0700 (PDT) (envelope-from jim@freeze.org) Date: Thu, 25 May 2000 21:57:04 -0700 (PDT) From: Jim Freeze X-Sender: jfreeze@web2.sea.nwserv.com To: Donald and Rosalyn Fast Cc: freebsd-questions@FreeBSD.ORG Subject: Re: Widespread panics on install of 4.0 In-Reply-To: <000601bfc6c5$ccbf2880$9232e8d8@bc.hsia.telus.net> Message-ID: MIME-Version: 1.0 Content-Type: TEXT/PLAIN; charset=US-ASCII X-Envelope-To: d_rfast@telus.net Sender: owner-freebsd-questions@FreeBSD.ORG Precedence: bulk X-Loop: FreeBSD.ORG On Thu, 25 May 2000, Donald and Rosalyn Fast wrote: > Hi, > > I hope someone can point out a way to install v4 on my machine. > 2 (distant) choice) hardware replacement suggestions. > > I have set of v3.1 CDs (which came with a recently purchased Complete FreeBSD 2nd ed). > This version will install properly and work. Is this on the same hardware? > When attempting to install ( with msdos, ftp or CD-ROM) v4.0 various panic situations > arise. All install methods will configure (both with and without an initial kernel config) > and start the installation (of # 9 X-User ). At various points during the install the > system panics and FreeBSD is then not bootable. try again (or boot into windows, search > and reread information on the web). > > Is there anything that needs to be changed for AMD K6(2)-400? > > panic: page fault > syncing disks ... 471 [repeated 20 times] > giving up on 246 buffers > uptime: 10m47s > > MSDOS (4-20000520-stable, also tried 4.0-RELEASE) > from c:\freeBSD folder > panic: ffs_valloc: dup alloc > syncing disks 188 162 12 1 1 1 1 1 1 (total of 17 x 1) > uptime: 6m54s > Whoa, this is deja-vu. I built my own system. First I started with a K6/2-350, but the thing kept having problems. I replaced the motherboard, thought it was bad, still had panics. Then the sales guy noticed that I was running the bus speed at 95Mhz (which the K6 manual says to). He thought that was the cause of the problem since he had reports from 'those in the know' that the chip couldn't actually handle that speed. So I clocked it at 66MHz, still had problems. Finally I got fed up with that chip and bought a K6/2-450 (1 month later it was only $20 more). This chip was supposed to be better. But, still, panic problems. Now this computer guy was somewhat informed, but he wasn't an EE. He did not use thermal puddy between the chip and the fan. So I figure that the chip may be thermally challenged. Then I got some help from this list (can't remember who) who said that their K6 was frequency challenged, and clocked their 450 down to 300MHz and then it worked 100%. I decided to try it in stages, so I clocked mine down to 400MHz. It worked! The chip stabalized. Now, I did not take the time to verify if it was thermal and/or frequency problems--I didn't care as long as I could get it to work. > Donald Fast > a not-yet-successful user of FreeBSD So, short of getting a real pentium chip, lower the clock on your K6, make sure there is thermal compound between the fan and the cpu and give it a whirl. Hopefully this make you a successful FreeBSD user. > Processor Type: AMD-K6(tm) 3D processor For grins, I renamed my computer eeyore. Now I always remember that its a little slow. Good luck ============================================ Jim Freeze jim@freeze.org www.freeze.org -------------- Save on CDs, DVDs and Books till May 31 2000 $10 Off a purchase of $30 and $33 Off a purchase of $100. Visit www.freeze.org ============================================ To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message