From owner-freebsd-questions@FreeBSD.ORG Sat May 30 15:30:27 2009 Return-Path: Delivered-To: freebsd-questions@freebsd.org Received: from mx1.freebsd.org (mx1.freebsd.org [IPv6:2001:4f8:fff6::34]) by hub.freebsd.org (Postfix) with ESMTP id B17C51065670 for ; Sat, 30 May 2009 15:30:27 +0000 (UTC) (envelope-from smithi@nimnet.asn.au) Received: from sola.nimnet.asn.au (paqi.nimnet.asn.au [220.233.188.227]) by mx1.freebsd.org (Postfix) with ESMTP id 2CA1C8FC2E for ; Sat, 30 May 2009 15:30:26 +0000 (UTC) (envelope-from smithi@nimnet.asn.au) Received: from localhost (localhost [127.0.0.1]) by sola.nimnet.asn.au (8.14.2/8.14.2) with ESMTP id n4UFUL4w065021; Sun, 31 May 2009 01:30:22 +1000 (EST) (envelope-from smithi@nimnet.asn.au) Date: Sun, 31 May 2009 01:30:21 +1000 (EST) From: Ian Smith To: Josef Moellers In-Reply-To: <20090528163523.453E210656CB@hub.freebsd.org> Message-ID: <20090531011825.A55023@sola.nimnet.asn.au> References: <20090528163523.453E210656CB@hub.freebsd.org> MIME-Version: 1.0 Content-Type: TEXT/PLAIN; charset=US-ASCII Cc: freebsd-questions@freebsd.org Subject: Re: Failure to get past a PCI bridge X-BeenThere: freebsd-questions@freebsd.org X-Mailman-Version: 2.1.5 Precedence: list List-Id: User questions List-Unsubscribe: , List-Archive: List-Post: List-Help: List-Subscribe: , X-List-Received-Date: Sat, 30 May 2009 15:30:27 -0000 On Thu, 28 May 2009 16:24:00 +0200 Josef Moellers wrote: > Hi, > > I'm trying to install 7.2-RELEASE on a pretty new system (a Fujitsu > RX300S5). > The first obstacle was the fact that while the system has an > AT-Keyboard-Controller, it ist not used (keyboard and mouse are > connected via USB) and I have found that I can get past that by specifying > > set hint.atkbd.0.disabled=1 > set hint.atkbdc.0.disabled=1 > > The install kernel then boots properly and reaches the "Country Selection". > At that point, no keyboard input is accepted. An optical mouse is off, > so I assume the keyboard to be off, too. > > I have hooked up a serial connection to log the kernel's output (some > 1000+ lines): > > set boot_serial=1 > set boot_verbose=1 > set boot_multicons=1 > set console="comconsole vidconsole" > > The following lines make me wonder if the kernel fails to get past PCI > bridges and this can't reach the UHCI controllers: > > pcib0: on acpi0 > pcib0: could not get PCI interrupt routing table for \_SB_.CPU0 - > AE_NOT_FOUND > : > pcib1: on acpi0 > pcib1: could not get PCI interrupt routing table for \_SB_.CPU1 - > AE_NOT_FOUND > : > pcib2: port 0xcf8-0xcff on acpi0 > pcib2: couldn't find _ADR > pcib2: trying bus number 2 > pci2: on pcib2 > pci2: domain=0, physical bus=2 > > I talked to the guy who does the BIOS for the machine and he says that > it makes no sense for the kernel to try and find the _PRT for \_SB_.CPU0 > or \_SB_.CPU1! > > Can anyone help? I haven't been using FreeBSD since 4.2 and haven't dug > through deep kernel functions for quite some time. Not directly, but you may do better posting that to the acpi@freebsd.org list. See archives at http://lists.freebsd.org/pipermail/freebsd-acpi/ cheers, Ian