From owner-freebsd-alpha Tue Oct 26 3:57:42 1999 Delivered-To: freebsd-alpha@freebsd.org Received: from alcanet.com.au (border.alcanet.com.au [203.62.196.10]) by hub.freebsd.org (Postfix) with ESMTP id 70DD514EE3 for ; Tue, 26 Oct 1999 03:57:36 -0700 (PDT) (envelope-from jeremyp@gsmx07.alcatel.com.au) Received: by border.alcanet.com.au id <40358>; Tue, 26 Oct 1999 20:52:37 +1000 Content-return: prohibited Date: Tue, 26 Oct 1999 20:57:26 +1000 From: Peter Jeremy Subject: Multia booting woes To: freebsd-alpha@FreeBSD.org Reply-To: peter.jeremy@alcatel.com.au Message-Id: <99Oct26.205237est.40358@border.alcanet.com.au> MIME-version: 1.0 X-Mailer: Mutt 1.0pre3i Content-type: text/plain; charset=us-ascii Sender: owner-freebsd-alpha@FreeBSD.ORG Precedence: bulk X-Loop: FreeBSD.org I thought this was all going to be easy when I decided to buy a Multia... Latest try: I've dd'd releases/3.2-RELEASE/floppies/boot.flp from 3.2-RELEASE CD-ROM 2 onto a SCSI disk, stuck the disk into the Multia and it still dies (log below). I presume the `Unit Attention' messages are being triggered by SCSI bus resets during the boot, rather than a disk problem. Any suggestions? (`%' in the following refers to the twirling bar). Testing Memory from 8 to 64 meg... Executing power-up script... Testing TGA version BL5 V3.8-3 Aug 10 1995 03:22:55 dka0.0.0.6.0 DKA0 SEAGATE ST32151N 9470 ewa0.0.0.8.0 EWA0 08-00-2B-E4-41-77 pka0.7.0.6.0 PKA0 SCSI Bus ID 7 64 Meg of system memory CPU speed is 166 MHZ Cache size is 256 Kbytes *** keyboard not plugged in... Keyboard error; using serial port terminal Switching network ewa0.0.0.8.0 from AUI to Thin Wire... Switching network ewa0.0.0.8.0 from Thin Wire to Twisted Pair... >>>boot dka0 (boot dka0.0.0.6.0 -flags 0) *** Soft Error - Error #27 - SCSI: sense key = 'Unit Attention' (29|02) from dka0.0.0.6.0 Diagnostic Name ID Device Pass Test Hard/Soft 26-OCT-2019 boot 00000089 0 0 0 1 19:45:39 *** End of Error *** block 0 of dka0.0.0.6.0 is a valid boot block reading 14 blocks from dka0.0.0.6.0 bootstrap code read in base = 166000, image_start = 0, image_bytes = 1c00 initializing HWRPB at 2000 initializing page table at 158000 initializing machine state setting affinity to the primary CPU jumping to bootstrap code *** Soft Error - Error #27 - SCSI: sense key = 'Unit Attention' (29|02) from dka0.0.0.6.0 Diagnostic Name ID Device Pass Test Hard/Soft 26-OCT-2019 boot 00000089 0 0 0 2 19:45:41 *** End of Error *** %Console: SRM firmware console VMS PAL rev: 0x1000000010530 OSF PAL rev: 0x1000000020123 Switch to OSF PAL code succeeded. FreeBSD/alpha SRM disk boot, Revision (jkh@beast.cdrom.com, Sun May 16 17:48:25 GMT 1999) Memory: 65536 k *** Soft Error - Error #27 - SCSI: sense key = 'Unit Attention' (29|02) from dka0.0.0.6.0 Diagnostic Name ID Device Pass Test Hard/Soft 26-OCT-2019 boot 00000089 0 0 0 3 19:45:44 *** End of Error *** %> load /kernel %inflate: (null) panic: free: guard1 fail @ 0x200094a0 halted CPU 0 halt code = 5 HALT instruction executed PC = 2001f3b8 access violation fault PCB = 03F542C0 (entry) PC = 0004FED0 VA = 00000028 exception context saved starting at 03F562C0 GPRs: 0: 00000000 00000000 16: 00000000 00000000 1: 00000000 000BFFFF 17: 00000000 000E1518 2: 00000000 0010B610 18: 00000000 000464D4 3: 00000000 00038B20 19: 00000000 00109390 4: 00000000 00000000 20: 00000000 00038320 5: 00000000 00038B20 21: 00000000 00110CA0 6: 00000000 00000000 22: 00000000 00142B90 7: 00000000 00000000 23: 00000000 00000000 8: 00000000 00000000 24: 00000000 00000000 9: 00000000 00000000 25: 00000000 00000002 10: 00000000 00000000 26: 00000000 0004FEB0 11: 00000000 00000000 27: 00000000 00114228 12: 00000000 00000000 28: 00000000 00016050 13: 00000000 00000000 29: 00000000 03F56428 14: 00000000 00000000 30: 00000000 03F56428 15: 00000000 00000000 dump of active call frames: PC = 0004FED0 PD = 0010B610 (decc$fclose) FP = 03F56428 SP = 03F56428 R2 R3 R4 R29 saved starting at 03F56430 R2 = 00111A30 R3 = 03F542C0 R4 = 03F54398 R29 = 03F56458 PC = 0006A83C PD = 00111A30 (krn$_process) FP = 03F56458 SP = 03F56458 R2 R3 R4 R5 R29 saved starting at 03F56460 R2 = 00000000 R3 = 00000000 R4 = 00000000 R5 = 00000000 R29 = 00000000 Brk 0 at 0012FF08 0012FF08! BPT -- Peter Jeremy (VK2PJ) peter.jeremy@alcatel.com.au Alcatel Australia Limited 41 Mandible St Phone: +61 2 9690 5019 ALEXANDRIA NSW 2015 Fax: +61 2 9690 5982 To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-alpha" in the body of the message