From owner-freebsd-questions Thu Jul 18 06:42:35 1996 Return-Path: owner-questions Received: (from root@localhost) by freefall.freebsd.org (8.7.5/8.7.3) id GAA18259 for questions-outgoing; Thu, 18 Jul 1996 06:42:35 -0700 (PDT) Received: from allmalt.cs.uwm.edu (allmalt.cs.uwm.edu [129.89.139.2]) by freefall.freebsd.org (8.7.5/8.7.3) with ESMTP id GAA18254 for ; Thu, 18 Jul 1996 06:42:33 -0700 (PDT) Received: (from scottk@localhost) by allmalt.cs.uwm.edu (8.7.3/8.7.3) id IAA23477 for questions@freebsd.org; Thu, 18 Jul 1996 08:42:50 -0500 (CDT) From: Scott Knaffla Message-Id: <199607181342.IAA23477@allmalt.cs.uwm.edu> Subject: 2.1.5 install failed with EISA Buslogic BT747S To: questions@freebsd.org Date: Thu, 18 Jul 1996 08:42:50 -0500 (CDT) X-Mailer: ELM [version 2.4 PL25] MIME-Version: 1.0 Content-Type: text/plain; charset=US-ASCII Content-Transfer-Encoding: 7bit Sender: owner-questions@freebsd.org X-Loop: FreeBSD.org Precedence: bulk Hi, I am try to install FreeBSD 2.1.5 (I also failed at 2.1.0 and the 6/12 snap of 2.2). I have a P24T (83Mhz) upgraded AMI Enterprise IV (Eisa machine). I stripped all the cards out except my Buslogic BT747S (Fast SCSI II, Eisa card, firmware 3.37, the latest) and ATI Mach32 (Also Eisa). I have a 2.88Mb 3.5 floppy now in 1.44 compatibility mode, I tried connecting it to both the motherboard and the SCSI card, and now it's currently connected to the motherboard. I have a 2Gb Barracuda (ST12550N I think the firmware is level 10) internal (termination point) and a Nec 3Xi and HP 35480 (4mm Dat) (termination point) external. I have 2 1Gb partitions, one for FreeBSD and one for Win95, the entire system is working fine for Win95 and I have previously had Dos, Win NT and NetBSD partitions on it. NetBSD was on there for about 2 years I remember having trouble installing NetBSD also, I think I had to make a custom kernel and take one of the floppies out of the kernel, to get that to work, something about the floppy driver grabbing interrupts that the SCSI one should be getting, but I don't remember about that very much. OK Enough about the history and the machine. When I put the floppy for 2.1.5 (I have used the same floppy to install 2 other machines so I think it should be fine), the system comes up, probe finds my SCSI card says it's reading the board settings and prints out that it's at 0x330-x333 dma 5 irq 11 but when I switch the the alternate console, there is no bt0 driver loaded up, and when in the main console window if I try to start to install it tells me there is no drive. I tried doing the custom boot and take everything else out and the same thing goes on. I think booting the normal default kernel probe see the bt and then thinks it's an adaptec, it talks to the hard drive with the aha dirver and get the model number and firmware from the seagate, but then fails when trying to do command with the adaptec driver. When I have the external cd and tape turned on I get this from the debugger window. Debugger ("bt742a") called bt0: abort operation has timed out bt0: not taking commands! Debugger ("bt742a") called bt0: Try to abort bt0: not taking commands! Debugger ("bt742a") called bt0: Abort operation has timed out bt0: not taking commands! Debugger ("bt742a") called bt0: Try to abort bt0: not taking commands! Debugger ("bt742a") called bt0: Abort operation has timed out I can't seem to get any further. I have read through the documentation and The card SCSI is at 0x330, the only requirement listed. Probe seems to like my system enough, it sees everything I have in my system. Any ideas?? Thanks, - Scott Scott Knaffla scottk@cs.uwm.edu