From owner-freebsd-questions Wed Feb 23 12:11:24 2000 Delivered-To: freebsd-questions@freebsd.org Received: from vitoria.ddsecurity.com.br (vitoria.ddsecurity.com.br [200.18.130.93]) by hub.freebsd.org (Postfix) with SMTP id D05D037B992 for ; Wed, 23 Feb 2000 12:11:11 -0800 (PST) (envelope-from grios@ddsecurity.com.br) Received: (qmail 61530 invoked by uid 1001); 23 Feb 2000 21:09:19 -0000 From: "Gustavo Rios" Date: Wed, 23 Feb 2000 18:09:19 -0300 (EST) To: Peter Schwenk Cc: Ertan Kucukoglu , questions@freebsd.org Subject: Re: PCI modem In-Reply-To: <38B400E5.9CD92DC1@math.udel.edu> Message-ID: MIME-Version: 1.0 Content-Type: TEXT/PLAIN; charset=US-ASCII Sender: owner-freebsd-questions@FreeBSD.ORG Precedence: bulk X-Loop: FreeBSD.ORG So, here is my kernel config file: # Only related to serial ports, nothing else # Serial (COM) ports #device sio0 at isa? disable port "IO_COM1" flags 0x10 tty irq 4 device sio1 at isa? port "IO_COM2" flags 0x10 tty irq 3 #device sio2 at isa? port "IO_COM3" tty irq 4 device sio4 at pci? port 0xE400 tty irq 12 #device sio3 at isa? disable port "IO_COM4" tty irq 9 Isn't it strange i got no message about this device detection? -- The thing i like most about Windows is .... You can download FreeBSD with it! On Wed, 23 Feb 2000, Peter Schwenk wrote: > Since it appears from your dmesg that you disabled your motherboard's first serial port (usually > IRQ, 0x3f8), you can use the FreeBSD kernel configuration screen to make sio0 match your PCI > modem parameters. > To enter the kernel configuration screen: > > * Press a key other than Enter when you see the "Hit [Enter] to boot immediately, or any other > key for command prompt." message during boot. > * At resulting prompt, enter 'boot -c' command. > * At next resulting prompt, enter 'visual' command. > * Top part of kernel config screen are enabled device drivers, bottom are disabled. You want > to go to the 'communications' section and change the parameters for sio0 (if you've truly > disabled it on the motherboard and don't need it) to match your PCI modem. > * Press Q to save the parameters and Q again to save the kernel configuration. > > Gustavo Rios wrote: > > > Model: US Robotics model 0727 > > Port: COM5 > > IRQ 12 > > IO E400 - E407 > > UART NS16550AN > > > > Can you point me the solution? > > > > Here goes my dmesg output: > > > > Copyright (c) 1992-1999 FreeBSD Inc. > > Copyright (c) 1982, 1986, 1989, 1991, 1993 > > The Regents of the University of California. All rights reserved. > > FreeBSD 3.4-STABLE #13: Wed Feb 23 13:10:01 GMT 2000 > > root@etosha:/usr/src/sys/compile/ETOSHA > > Timecounter "i8254" frequency 1193182 Hz > > CPU: Pentium II (267.27-MHz 686-class CPU) > > Origin = "GenuineIntel" Id = 0x634 Stepping = 4 > > Features=0x80f9ff > > real memory = 134217728 (131072K bytes) > > avail memory = 127422464 (124436K bytes) > > Preloaded elf kernel "kernel" at 0xc0304000. > > Preloaded userconfig_script "/boot/kernel.conf" at 0xc030409c. > > Preloaded elf module "splash_bmp.ko" at 0xc03040ec. > > Preloaded elf module "vesa.ko" at 0xc0304190. > > Preloaded splash_image_data "/boot/splash.bmp" at 0xc030422c. > > VESA: v2.0, 4096k memory, flags:0x0, mode table:0xc00c6d9d (c0006d9d) > > VESA: Diamond Multimedia Systems, Inc. > > Pentium Pro MTRR support enabled > > Probing for devices on PCI bus 0: > > chip0: rev 0x03 on pci0.0.0 > > chip1: rev 0x03 on pci0.1.0 > > chip2: rev 0x02 on pci0.7.0 > > ide_pci0: rev 0x01 on pci0.7.1 > > chip3: rev 0x02 on pci0.7.3 > > Probing for devices on PCI bus 1: > > vga0: rev 0x04 int a irq 11 on pci1.0.0 > > Probing for devices on the ISA bus: > > sc0 flags 0x6 on isa > > sc0: VGA color <5 virtual consoles, flags=0x6> > > ed0 at 0x300-0x31f irq 10 on isa > > ed0: address 00:00:21:6c:8f:e0, type NE2000 (16 bit) > > atkbdc0 at 0x60-0x6f on motherboard > > atkbd0 irq 1 on isa > > sio1 at 0x2f8-0x2ff irq 3 flags 0x10 on isa > > sio1: type 16550A > > pcm0 at 0x220 irq 5 drq 1 flags 0x15 on isa > > fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa > > fdc0: FIFO enabled, 8 bytes threshold > > fd0: 1.44MB 3.5in > > wdc0 at 0x1f0-0x1f7 irq 14 on isa > > wdc0: unit 0 (wd0): , LBA, DMA, 32-bit, multi-block-16, sleep-hack > > wd0: 8063MB (16514064 sectors), 17475 cyls, 15 heads, 63 S/T, 512 B/S > > wdc1 at 0x170-0x177 irq 15 on isa > > wdc1: unit 0 (atapi): , removable, intr, iordis > > wfd0: medium type unknown (no disk) > > wfd0: buggy Zip drive, 64-block transfer limit set > > wdc1: unit 1 (atapi): < 34X CD-ROM/VER 1.D1>, removable, accel, dma, iordy > > acd0: drive speed 343 - 3781KB/sec, 128KB cache > > acd0: supported read types: CD-R, CD-RW, CD-DA, packet track > > acd0: Audio: play, 255 volume levels > > acd0: Mechanism: ejectable tray > > acd0: Medium: no/blank disc inside, unlocked > > ppc0 at 0x378 irq 7 flags 0x40 on isa > > ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode > > lpt0: on ppbus 0 > > lpt0: Interrupt-driven port > > vga0 at 0x3c0-0x3df maddr 0xa0000 msize 131072 on isa > > npx0 on motherboard > > npx0: INT 16 interface > > apm0 flags 0x31 on isa > > apm: found APM BIOS version 1.2 > > changing root device to wd0s1a > > > > -- > > The thing i like most about Windows is .... > > You can download FreeBSD with it! > > > > On Wed, 23 Feb 2000, Ertan Kucukoglu wrote: > > > > > Gustavo Rios wrote: > > > > > > > > Dear Gentleman, > > > > > > > > I suppose it's not a WinModem! > > > > It's manual day nothing about being WinModem, but it works in a DOS > > > > environment (I do not have Win Installed). > > > > > > Dear Gustavo, > > > > > > Can you send me the product code of your modem. I want to check it on > > > www.3com.com (Don't misunderstand me. I hear first time that a PCI > > > modem that isn't a WinModem.) > > > > > > And, can you say which COM port you use under DOS? Or does modem have > > > jumper settings on it? Also please send your dmesg output. > > > > > > > Just after turn my obx on, i get this: > > > > (Only related to modem adition) > > > > > > > > PCI device listing: > > > > Bus No Device No Func No Vendor ID Device ID Device Class IRQ > > > > 0 7 2 8086 7112 Serial Bus Controller 12 > > > > 0 14 0 12B9 1008 Simple COMM. Controller 12 > > > > > > > > Can anyone here point me which kernel options/device should i add to my > > > > kernel config file! > > > > > > > > > > If it's a real modem then you should use it just setting the port > > > settings to COM1 or COM2. (I'm not sure maybe this is done with software > > > not with jumpers) > > > > > > If you use a port number of COM3 or COM4 under DOS and using GENERIC > > > kernel. Then you supposed to make your own kernel (by default COM3 and > > > COM4 are disabled) and enable that ports. > > > > > > (I suppose you know how to compile your kernel.) > > > > > > > Thanks a lot for your time and cooperation. > > > > best regards! > > > > > > > > -- > > > > The thing i like most about Windows is .... > > > > You can download FreeBSD with it! > > > > > > Hope helps. > > > > > > Regards, > > > > > > -- > > > Ertan Kucukoglu > > > ertank@ozlerplastik.com > > > > > > > To Unsubscribe: send mail to majordomo@FreeBSD.org > > with "unsubscribe freebsd-questions" in the body of the message > > -- > PETER SCHWENK | UNIX System Administrator > Department of Mathematical Sciences | University of Delaware > schwenk@math.udel.edu | (302)831-0437 > > > > > > To Unsubscribe: send mail to majordomo@FreeBSD.org > with "unsubscribe freebsd-questions" in the body of the message > To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message