From owner-freebsd-scsi Wed Jan 22 09:46:22 1997 Return-Path: Received: (from root@localhost) by freefall.freebsd.org (8.8.5/8.8.5) id JAA16266 for freebsd-scsi-outgoing; Wed, 22 Jan 1997 09:46:22 -0800 (PST) Received: from prometeo.prometeo.it (prometeo.prometeo.it [194.21.36.33]) by freefall.freebsd.org (8.8.5/8.8.5) with ESMTP id JAA16259; Wed, 22 Jan 1997 09:46:07 -0800 (PST) Received: from tgioc.prometeo.it (tgioc.prometeo.it [194.21.36.34]) by prometeo.prometeo.it (8.7.5/8.7.3) with SMTP id SAA24778; Wed, 22 Jan 1997 18:53:07 +0100 (MET) Message-Id: <199701221753.SAA24778@prometeo.prometeo.it> Comments: Authenticated sender is From: "Coi Giovanni" Organization: Prometeo srl To: freebsd-question@FreeBSD.org, freebsd-scsi@FreeBSD.org Date: Wed, 22 Jan 1997 18:40:27 +0000 Subject: AHA-1522A and DAT Data phase error Reply-to: Coi_Giovanni@prometeo.it X-Confirm-Reading-To: Coi_Giovanni@prometeo.it X-pmrqc: 1 Priority: normal X-mailer: Pegasus Mail for Win32 (v2.50) Sender: owner-freebsd-scsi@FreeBSD.org X-Loop: FreeBSD.org Precedence: bulk Hello, I have a SONY SDT-5200 3.26 tape backup (DAT) which I am trying to run. The SCSI controller is a AHA-1522A (ISA bus) when I try to write on tape (with dump for example) I get the following error messages on console: st0(aic0:5:0): ABORTED COMMAND info:4 asc:4b,0 Data phase error st0(aic0:5:0): HARDWARE FAILURE info:14 asc:44,0 Internal target failure st0(aic0:5:0): HARDWARE FAILURE info:14 asc:44,0 Internal target failure st0(aic0:5:0): HARDWARE FAILURE info:1 asc:44,0 Internal target failure the dump command is dump 0uBbf 2000000 10 /dev/rst0 /dev/wd0a but I try also with dump 0uBbf 2000000 10 /dev/rst0 / whit the same results and this is the output of dump on stderr: DUMP: Date of this level 0 dump: Wed Jan 22 13:52:54 1997 DUMP: Date of last level 0 dump: the epoch DUMP: Dumping /dev/rwd0a (/) to /dev/rst0 DUMP: mapping (Pass I) [regular files] DUMP: mapping (Pass II) [directories] DUMP: estimated 15086 tape blocks on 0.01 tape(s). DUMP: dumping (Pass III) [directories] DUMP: dumping (Pass IV) [regular files] ... error messages on console.... DUMP: End of tape detected DUMP: Closing /dev/rst0 DUMP: Change Volumes: Mount volume #2 DUMP: Is the new volume mounted and ready to go?: ("yes" or "no") I reply no DUMP: Do you want to abort?: ("yes" or "no") I reply yes DUMP: The ENTIRE dump is aborted. Note: a) after I run the dump command after signaling DUMP: dumping (Pass IV) [reguler files] the system freeze. It do not respond at console, no on other telnet session, no on other vitrual console. After it finish (with error) all return to normal state. b) I have tryed the following command: tar cvf /dev/rst0 /etc and it goes. Then I can run also tar tvf /dev/rst0 and see the correct listing of etc's file. I think it was because there are few data in /etc. c) the _same_ DAT works fine when I connect it to a windows NT 4.0 box (but with a SCSI controller more quick, an PCI Adaptec AHA-2940 d) as you can see from the startup log (below) I have also a SCSI CDROM that work fine (I have copied with success a file of about 10Mbyte from it). Anyone has some suggestions? Please reply directly to me or on freebsd-question list. TIA. Follow my system configuration parameter: --------------------------------------------------------------- controller aic0 at isa? port 0x140 bio irq 10 vector aicintr controller scbus0 at aic0 # Single bus device disk sd0 at scbus0 target 4 unit 0 tape st0 at scbus0 target 5 unit 0 device cd0 at scbus0 target 3 unit 0 options SCSI_DELAY=30 options SCSIDEBUG --------------------------------------------------------------- Follow my startup log ----------------------------------------------------------- FreeBSD 2.1.5-RELEASE #0: Wed Jan 22 15:56:04 MET 1997 CPU: i486DX (486-class CPU) real memory = 16777216 (16384K bytes) avail memory = 14835712 (14488K bytes) Probing for devices on the ISA bus: sc0 at 0x60-0x6f irq 1 on motherboard sc0: VGA mono <4 virtual consoles, flags=0x0> ed0 at 0x340-0x35f irq 5 on isa ed0: address 00:00:1b:3a:c4:88, type NE2000 (16 bit) lpt0 at 0x378-0x37f irq 7 on isa lpt0: Interrupt-driven port lp0: TCP/IP capable interface sio0 at 0x3f8-0x3ff irq 4 on isa sio0: type 16450 sio1 at 0x2f8-0x2ff irq 3 on isa sio1: type 16450 aic0 at 0x140-0x15f irq 10 on isa aic0 waiting for scsi devices to settle (aic0:3:0): "NEC CD-ROM DRIVE:501 2.2" type 5 removable SCSI 2 cd0(aic0:3:0): CD-ROM cd present.[328201 x 2048 byte records] (aic0:4:0): "IBM MTA-3230TC2210!B 0" type 7 removable SCSI 2 uk0(aic0:4:0): Unknown (aic0:5:0): "SONY SDT-5200 3.26" type 1 removable SCSI 2 st0(aic0:5:0): Sequential-Access density code 0x13, 512-byte blocks, write-enabled wdc0 at 0x1f0-0x1f7 irq 14 flags 0x80008000 on isa wdc0: unit 0 (wd0): wd0: 814MB (1667232 sectors), 1654 cyls, 16 heads, 63 S/T, 512 B/S wdc0: unit 1 (wd1): wd1: 515MB (1056384 sectors), 1048 cyls, 16 heads, 63 S/T, 512 B/S fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa fdc0: NEC 765 fd0: 1.44MB 3.5in mcd0: type Mitsumi FX001D, version info: D 2 mcd0 at 0x320- 0x323 irq 11 on isa npx0 on motherboard npx0: INT 16 interface ----------------------------------------------------------- ---------------------------------------------------------- Prometeo srl - Progetti e Metodologie Informatiche Internet Services Provider Coi Giovanni Voice : +39 (041)5701366 Via Giudecca 15 Fax : +39 (041)5701005 30035 MIRANO (VE) - ITALY e-mail: coi@prometeo.it http://www.prometeo.it