From owner-freebsd-questions Fri Jun 12 11:26:24 1998 Return-Path: Received: (from majordom@localhost) by hub.freebsd.org (8.8.8/8.8.8) id LAA07813 for freebsd-questions-outgoing; Fri, 12 Jun 1998 11:26:24 -0700 (PDT) (envelope-from owner-freebsd-questions@FreeBSD.ORG) Received: from local-motion.rutgers.edu (talukdar@local-motion.rutgers.edu [128.6.5.114]) by hub.freebsd.org (8.8.8/8.8.8) with ESMTP id LAA07647 for ; Fri, 12 Jun 1998 11:25:32 -0700 (PDT) (envelope-from talukdar@local-motion.rutgers.edu) Received: (from talukdar@localhost) by local-motion.rutgers.edu (8.8.8/8.8.8) id OAA14614; Fri, 12 Jun 1998 14:25:30 -0400 (EDT) Date: Fri, 12 Jun 1998 14:25:30 -0400 (EDT) From: Anup Talukdar Message-Id: <199806121825.OAA14614@local-motion.rutgers.edu> To: freebsd-questions@FreeBSD.ORG Subject: Help : Problems with network interfaces Cc: talukdar@paul.rutgers.edu Sender: owner-freebsd-questions@FreeBSD.ORG Precedence: bulk X-Loop: FreeBSD.ORG Hi, I am experiencing the following two problems when trying to install FreeBSD 2.2.6 on my DELL Latitude XPi Laptop. Problem 1 . I have used a 3Com 3C589C EtherLink III LAN PC Card as the network interface. I need multicasting enabled on this ethernet interface. However the interface 'zp0' does not have multicasting enabled (as shown below in the output of the command 'ifconfig -a'). >#ifconfig -a > >lp0: flags=8810 mtu 1500 >zp0: flags=1843 mtu 1500 > inet 128.6.157.141 netmask 0xffffffe0 broadcast 128.6.157.159 > ether 00:a0:24:63:b9:e7 >tun0: flags=8010 mtu 1500 >sl0: flags=c010 mtu 552 >ppp0: flags=8010 mtu 1500 >lo0: flags=8049 mtu 16384 > inet 127.0.0.1 netmask 0xff000000 I will greatly appreciate, if someone can inform me how to enable MULTICAST on 'zp0'. Problem 2. If I remove the 3Com EtheLink III 3C589C and instead insert a NOTEWORTHY ETHERNET CARD (PC Card), then I cannot access the network. The output of the command 'ifconfig -a' is as follows : >lp0: flags=8810 mtu 1500 >ze0: flags=843 mtu 1500 > inet 128.6.157.141 netmask 0xffffffe0 broadcast 128.6.157.159 > ether 00:04:ac:d5:f5:9e >tun0: flags=8010 mtu 1500 >sl0: flags=c010 mtu 552 >ppp0: flags=8010 mtu 1500 >lo0: flags=8049 mtu 16384 > inet 127.0.0.1 netmask 0xff000000 The following message is generated periodically : > /kernel : ze0 : device timeout. isr=03, imr=9f, imask=0000 I will be grateful, if someone can kindly inform me how to correct the problem and enable multicasting on both cards. ----------------------System Configuration used------------------------------- My System Configuration : DEll Latitude XPi ----Kernel Configuration file : MYKERNEL (modified from GENERIC)------- # # GENERIC -- Generic machine with WD/AHx/NCR/BTx family disks # # For more information read the handbook part System Administration -> # Configuring the FreeBSD Kernel -> The Configuration File. # The handbook is available in /usr/share/doc/handbook or online as # latest version from the FreeBSD World Wide Web server # # # An exhaustive list of options and more detailed explanations of the # device lines is present in the ./LINT configuration file. If you are # in doubt as to the purpose or necessity of a line, check first in LINT. # # $Id: GENERIC,v 1.77.2.22 1998/03/24 01:20:14 jkh Exp $ machine "i386" cpu "I386_CPU" cpu "I486_CPU" cpu "I586_CPU" cpu "I686_CPU" ident GENERIC maxusers 10 options MATH_EMULATE #Support for x87 emulation options INET #InterNETworking options FFS #Berkeley Fast Filesystem options NFS #Network Filesystem options MSDOSFS #MSDOS Filesystem options "CD9660" #ISO 9660 Filesystem options PROCFS #Process filesystem options "COMPAT_43" #Compatible with BSD 4.3 [KEEP THIS!] options SCSI_DELAY=15 #Be pessimistic about Joe SCSI device options BOUNCE_BUFFERS #include support for DMA bounce buffers options UCONSOLE #Allow users to grab the console options FAILSAFE #Be conservative options USERCONFIG #boot -c editor options VISUAL_USERCONFIG #visual boot -c editor config kernel root on wd0 controller isa0 controller eisa0 controller pci0 controller fdc0 at isa? port "IO_FD1" bio irq 6 drq 2 vector fdintr disk fd0 at fdc0 drive 0 disk fd1 at fdc0 drive 1 tape ft0 at fdc0 drive 2 options "CMD640" # work around CMD640 chip deficiency controller wdc0 at isa? port "IO_WD1" bio irq 14 vector wdintr disk wd0 at wdc0 drive 0 disk wd1 at wdc0 drive 1 controller wdc1 at isa? port "IO_WD2" bio irq 15 vector wdintr disk wd2 at wdc1 drive 0 disk wd3 at wdc1 drive 1 options ATAPI #Enable ATAPI support for IDE bus options ATAPI_STATIC #Don't do it as an LKM device wcd0 #IDE CD-ROM device wfd0 #IDE floppy (LS-120) # A single entry for any of these controllers (ncr, ahb, ahc, amd) is # sufficient for any number of installed devices. # # Note: The dpt driver is present in this release but was left disabled # due to its relatively late entry (it's almost certainly benign to enable # it but we didn't want to risk any chance of destabilizing 2.2.6). To # enable DPT support, uncomment the dpt0 controller entry and the two # options DPTOPT and DPT_MEASURE_PERFORMANCE entries below. controller ncr0 controller amd0 controller ahb0 controller ahc0 #controller dpt0 controller bt0 at isa? port "IO_BT0" bio irq ? vector bt_isa_intr controller uha0 at isa? port "IO_UHA0" bio irq ? drq 5 vector uhaintr controller aha0 at isa? port "IO_AHA0" bio irq ? drq 5 vector ahaintr controller aic0 at isa? port 0x340 bio irq 11 vector aicintr controller nca0 at isa? port 0x1f88 bio irq 10 vector ncaintr controller nca1 at isa? port 0x350 bio irq 5 vector ncaintr controller sea0 at isa? bio irq 5 iomem 0xc8000 iosiz 0x2000 vector seaintr #options DPTOPT # will go away soon #options DPT_MEASURE_PERFORMANCE # just enable for now #options DPT_VERIFY_HINTR # Some hardware must have it! #options DPT_TRACK_CCB_STATES # Some hardware must have it! #options DPT_HANDLE_TIMEOUTS # Some hardware must have it! #options DPT_TIMEOUT_FACTOR=4 # Some hardware needs more controller scbus0 device sd0 device od0 #See LINT for possible `od' options. device st0 device cd0 #Only need one of these, the code dynamically grows device wt0 at isa? port 0x300 bio irq 5 drq 1 vector wtintr device mcd0 at isa? port 0x300 bio irq 10 vector mcdintr controller matcd0 at isa? port 0x230 bio device scd0 at isa? port 0x230 bio # syscons is the default console driver, resembling an SCO console device sc0 at isa? port "IO_KBD" tty irq 1 vector scintr # Enable this and PCVT_FREEBSD for pcvt vt220 compatible console driver #device vt0 at isa? port "IO_KBD" tty irq 1 vector pcrint #options XSERVER # support for X server #options FAT_CURSOR # start with block cursor # If you have a ThinkPAD, uncomment this along with the rest of the PCVT lines #options PCVT_SCANSET=2 # IBM keyboards are non-std # Mandatory, don't remove device npx0 at isa? port "IO_NPX" flags 0x1 irq 13 vector npxintr # # Laptop support (see LINT for more options) # device apm0 at isa? disable # Advanced Power Management options APM_BROKEN_STATCLOCK # Workaround some buggy APM BIOS # PCCARD (PCMCIA) support #controller card0 #device pcic0 at card? #device pcic1 at card? device sio0 at isa? port "IO_COM1" tty irq 4 vector siointr device sio1 at isa? port "IO_COM2" tty irq 3 vector siointr device sio2 at isa? disable port "IO_COM3" tty irq 5 vector siointr device sio3 at isa? disable port "IO_COM4" tty irq 9 vector siointr device lpt0 at isa? port? tty irq 7 vector lptintr device lpt1 at isa? port? tty device mse0 at isa? port 0x23c tty irq 5 vector mseintr device psm0 at isa? port "IO_KBD" conflicts tty irq 12 vector psmintr # Order is important here due to intrusive probes, do *not* alphabetize # this list of network interfaces until the probes have been fixed. # Right now it appears that the ie0 must be probed before ep0. See # revision 1.20 of this file. device de0 device fxp0 device tx0 device vx0 device ed0 at isa? port 0x280 net irq 10 iomem 0xd8000 vector edintr device ie0 at isa? port 0x300 net irq 10 iomem 0xd0000 vector ieintr device ep0 at isa? port 0x300 net irq 10 vector epintr device ex0 at isa? port? net irq? vector exintr device fe0 at isa? port 0x300 net irq ? vector feintr device le0 at isa? port 0x300 net irq 5 iomem 0xd0000 vector le_intr device lnc0 at isa? port 0x280 net irq 10 drq 0 vector lncintr device ze0 at isa? port 0x300 net irq 5 iomem 0xd8000 vector zeintr device zp0 at isa? port 0x300 net irq 10 iomem 0xd8000 vector zpintr pseudo-device loop pseudo-device ether pseudo-device log pseudo-device sl 1 pseudo-device ppp 1 pseudo-device vn 1 pseudo-device tun 1 pseudo-device pty 16 pseudo-device gzip # Exec gzipped a.out's # KTRACE enables the system-call tracing facility ktrace(2). # This adds 4 KB bloat to your kernel, and slightly increases # the costs of each syscall. options KTRACE #kernel tracing # This provides support for System V shared memory. # options SYSVSHM To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message