Skip site navigation (1)Skip section navigation (2)
Date:      Sun, 11 Aug 2002 17:51:35 +1000
From:      "Chris Richards" <chrisric@magna.com.au>
To:        <freebsd-questions@FreeBSD.ORG>
Subject:   kernel panic - ATA failure after upgrading to 4.6-STABLE
Message-ID:  <000001c2410b$eb48aed0$020a0a0a@rocko>

Next in thread | Raw E-Mail | Index | Archive | Help
Hi Everyone,

I have been trying to upgrade to 4.6-STABLE from 4.6-RELEASE for 3 days
now..... No matter what I try I get the below errors on boot.

Steps I have taken:

CVSuped my full src (10/08/02)
make -j 4 buildworld
make buildkernel KERNCONF=MYKERNEL
make installkernel KERNCONF=MYKERNEL
make installworld
backup /etc
run mergemaster
rebuild /dev
rebuild sysinstall

I get no errors what so ever from all the above, only when I reboot and
it tries to boot on the new kernel do I have issues. I even tried
building the GENERIC kernel and it had the same problem.

If you have any ideas as to what might be happening please help me out
:) Also if you require more info just shoot me an email - I have
included a "dmesg" at the bottom just to give an overview of my system.

Thanks for reading!

Cheers,
Chris

------------------------------------------------------------------------
<snip>
ad0: timeout waiting for interrupt
ad0: timeout waiting for interrupt
ad0: enabling readahead cache failed
ad0: timeout waiting for interrupt
ad0: enabling write cache failed
ad0: READ command timeout tag=0, serv=0 - resetting
ata0: resetting devices .. done.
ad0: 9779MB <WDC WD102BA> [19870/16/63] at ata0-master UDMA33
ad0: READ command timeout tag=0, serv=0 - resetting
ata0: resetting devices .. done.
acd0: MODE_SENSE_BIG command timeout - resetting
ata1: resetting devices .. done.
ad0: READ command timeout tag=0, serv=0 - resetting
ata0: resetting devices .. done.
acd0: MODE_SENSE_BIG command timeout - resetting
ata1: resetting devices .. done.
ad0: READ command timeout tag=0, serv=0 - resetting
ad0: trying fallback to PIO mode
ata0: resetting devices .. done.
acd0: MODE_SENSE_BIG command timeout - resetting
ata1: resetting devices .. done.
ad0: READ command timeout tag=0, serv=0 - resetting
ata0: resetting devices .. ata0-slave: ATA identify retires exceeded
done
acd0: MODE_SENSE_BIG command timeout - resetting
ata1: resetting devices .. done.

Fatal trap 12: page fault while in kernel mode
fault virtual address		= 0xb
fault code				= supervisor read, page not
present
instruction pointer		= 0x8:0xc012fad9
stack pointer			= 0x10:0xc0301f04
frame pointer			= 0x10:0xc0301f10
code segment			= base 0x0, limit 0xfffff, type 0x1b
					= DPC
processor eflags			= interrupt enabled, resume,
IOPL=0
current process			= 0 (swapper)
interrupt mask			= bio
trap number				= 12
panic: page fault

syncing disks
done

------------------------------------------------------------------------
dmesg:
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights
reserved.
FreeBSD 4.6-RELEASE #0: Tue Jun 11 06:14:12 GMT 2002
    murray@builder.freebsdmall.com:/usr/src/sys/compile/GENERIC
Timecounter "i8254"  frequency 1193182 Hz
CPU: Pentium II/Pentium II Xeon/Celeron (400.91-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x665  Stepping = 5
 
Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,C
MOV,PAT,PSE36,MMX,FXSR>
real memory  = 402653184 (393216K bytes)
avail memory = 386564096 (377504K bytes)
Preloaded elf kernel "kernel.GENERIC" at 0xc04d0000.
Pentium Pro MTRR support enabled
md0: Malloc disk
Using $PIR table, 7 entries at 0xc00f0cc0
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443LX (440 LX) host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib1: <Intel 82443LX (440 LX) PCI-PCI (AGP) bridge> at device 1.0 on
pci0
pci1: <PCI bus> on pcib1
pci1: <3Dfx Voodoo 3 graphics accelerator> at 0.0 irq 11
isab0: <Intel 82371AB PCI to ISA bridge> at device 4.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xb800-0xb80f at device 4.1
on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xb400-0xb41f irq
9 at device 4.2 on pci0
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
chip1: <Intel 82371AB Power management controller> port 0xe800-0xe80f at
device 4.3 on pci0
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xb000-0xb03f mem
0xdd000000-0xdd0fffff,0xdd800000-0xdd800fff irq 9 at device 10.0 on pci0
fxp0: Ethernet address 00:90:27:76:db:53
inphy0: <i82555 10/100 media interface> on miibus0
inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isa0: too many dependant configs (8)
isa0: unexpected small tag 14
orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xc8fff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on
isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model MouseMan+, device ID 0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/9 bytes threshold
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
ad0: 9779MB <WDC WD102BA> [19870/16/63] at ata0-master UDMA33
acd0: CDROM <MATSHITA CR-585> at ata1-master PIO3
Mounting root from ufs:/dev/ad0s1a


To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-questions" in the body of the message




Want to link to this message? Use this URL: <http://docs.FreeBSD.org/cgi/mid.cgi?000001c2410b$eb48aed0$020a0a0a>