Skip site navigation (1)Skip section navigation (2)
Date:      Sun, 20 Jul 2003 10:49:49 +0200
From:      "Petr Holub" <hopet@ics.muni.cz>
To:        "Hidetoshi Shimokawa" <simokawa@sat.t.u-tokyo.ac.jp>
Cc:        firewire@freebsd.org
Subject:   RE: firewire problem on 5.1-RELEASE
Message-ID:  <000001c34e9b$e0d99880$2be86cc2@kloboucek>
In-Reply-To: <ybsbrvqpnku.wl@ett.sat.t.u-tokyo.ac.jp>

Next in thread | Previous in thread | Raw E-Mail | Index | Archive | Help
Hi Hidetoshi,

> Those may indicate some hardware problem.
> 5.1 does more strict check on sid buffer.

the machine is the same and it used to work on 5.0. When I say
"work" I mean I've been able to read from the camera without any
problem.

If it helps dmesg output is below.

> > fwohci0: IR DMA overrun (0x40008011)
> > fwohci0: IR DMA overrun (0x40008011)
> > fwohci0: IR DMA overrun (0x40008011)
> > fwohci0: IR DMA overrun (0x40008011)
>
> How do you read from camera and where do you write the data?
> If you cannot read/write fast enough, the buffer overrun
> could ocurr.

The code for reading is based on your dv/dvrecv/dvsend that you gave
me some time ago (approx. March this year) when I was wondering
why DVTS doesn't work. This code used to work on 5.0 so that's
why I'm a bit confused why it stopped working.

Thanks a lot,
Petr

================================================================
                            Petr Holub
CESNET z.s.p.o.                       Supercomputing Center Brno
Zikova 4                             Institute of Compt. Science
162 00 Praha 6, CZ                            Masaryk University
Czech Republic                     Botanicka 68a, 60200 Brno, CZ
e-mail: Petr.Holub@cesnet.cz               phone: +420-541512272
                                             fax: +420-541212747
                                       e-mail: hopet@ics.muni.cz



Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD 5.1-RELEASE #1: Wed Jul  2 23:11:32 CEST 2003
    toor@trurl.fi.muni.cz:/usr/src/sys/i386/compile/TRURL
Preloaded elf kernel "/boot/kernel/kernel" at 0xc076a000.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc076a21c.
Timecounter "i8254"  frequency 1193182 Hz
Timecounter "TSC"  frequency 2372930576 Hz
CPU: Intel(R) Xeon(TM) CPU 2.40GHz (2372.93-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0xf27  Stepping = 7

Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,
DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Hyperthreading: 2 logical CPUs
real memory  = 1073180672 (1023 MB)
avail memory = 1034649600 (986 MB)
Changing APIC ID for IO APIC #0 from 0 to 4 on chip
Programming 24 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
 cpu0 (BSP): apic id:  0, version: 0x00050014, at 0xfee00000
 cpu1 (AP):  apic id:  1, version: 0x00050014, at 0xfee00000
 cpu2 (AP):  apic id:  2, version: 0x00050014, at 0xfee00000
 cpu3 (AP):  apic id:  3, version: 0x00050014, at 0xfee00000
 io0 (APIC): apic id:  4, version: 0x00178020, at 0xfec00000
Pentium Pro MTRR support enabled
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <DELL   WS 530 > on motherboard
pcibios: BIOS version 2.10
Using $PIR table, 12 entries at 0xc00fb9a0
acpi0: power button is handled as a fixed feature programming model.
Timecounter "ACPI-fast"  frequency 3579545 Hz
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
acpi_cpu0: <CPU> port 0x530-0x537 on acpi0
acpi_cpu1: <CPU> port 0x530-0x537 on acpi0
acpi_cpu2: <CPU> port 0x530-0x537 on acpi0
acpi_cpu3: <CPU> port 0x530-0x537 on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
IOAPIC #0 intpin 19 -> irq 2
IOAPIC #0 intpin 17 -> irq 13
IOAPIC #0 intpin 23 -> irq 16
agp0: <Intel 82860 host to AGP bridge> mem 0xf0000000-0xf7ffffff at device 0.0 on pci0
pcib1: <PCIBIOS PCI-PCI bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
IOAPIC #0 intpin 16 -> irq 17
pci1: <display, VGA> at device 0.0 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> at device 2.0 on pci0
pci2: <ACPI PCI bus> on pcib2
pcib3: <ACPI PCI-PCI bridge> at device 31.0 on pci2
pci3: <ACPI PCI bus> on pcib3
IOAPIC #0 intpin 20 -> irq 18
IOAPIC #0 intpin 22 -> irq 19
pci3: <base peripheral, interrupt controller> at device 0.0 (no driver attached)
em0: <Intel(R) PRO/1000 Network Connection, Version - 1.5.31> port 0xece0-0xecff mem
0xfe4a0000-0xfe4bffff,0xfe4c0000-0xfe4dffff irq 18 at device 12.0 on pci3
em0:  Speed:100 Mbps  Duplex:Full
ahc0: <Adaptec aic7892 Ultra160 SCSI adapter> port 0xe800-0xe8ff mem 0xfe4fe000-0xfe4fefff irq 19 at
device 14.0 on pci3
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
pcib4: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci4: <ACPI PCI bus> on pcib4
IOAPIC #0 intpin 18 -> irq 20
xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0xdc80-0xdcff mem 0xfe1ffc00-0xfe1ffc7f irq 16 at
device 11.0 on pci4
xl0: Ethernet address: 00:08:74:39:45:65
miibus0: <MII bus> on xl0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fwohci0: <Texas Instruments TSB12LV26> mem 0xfe1f8000-0xfe1fbfff,0xfe1ff000-0xfe1ff7ff irq 17 at
device 12.0 on pci4
fwohci0: OHCI version 1.0 (ROM=0)
fwohci0: No. of Isochronous channel is 4.
fwohci0: EUI64 80:74:08:00:65:45:39:00
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
if_fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 82:74:08:45:39:00
sbp0: <SBP2/SCSI over firewire> on firewire0
fwohci0: Initiate bus reset
pcm0: <Creative EMU10K1> port 0xdc60-0xdc7f irq 13 at device 13.0 on pci4
pcm0: <TriTech TR28602 AC97 Codec>
bktr0: <BrookTree 878> mem 0xfa003000-0xfa003fff irq 20 at device 14.0 on pci4
bktr0: Warning - card vendor 0xfefe (model 0x0012) unknown.
bktr0: Pinnacle/Miro TV, Temic NTSC tuner.
pci4: <multimedia> at device 14.1 (no driver attached)
bktr1: <BrookTree 878> mem 0xfa001000-0xfa001fff irq 2 at device 15.0 on pci4
bktr1: Warning - card vendor 0x11bd (model 0x0012) unknown.
bktr1: Pinnacle/Miro TV, Temic NTSC tuner.
pci4: <multimedia> at device 15.1 (no driver attached)
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH2 UDMA100 controller> port 0xffa0-0xffaf at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82801BA/BAM (ICH2) USB controller USB-A> port 0xff80-0xff9f irq 2 at device 31.2 on
pci0
usb0: <Intel 82801BA/BAM (ICH2) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
uhci1: <Intel 82801BA/BAM (ICH2) USB controller USB-B> port 0xff60-0xff7f irq 16 at device 31.4 on
pci0
usb1: <Intel 82801BA/BAM (ICH2) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
pcm1: <Intel 82801BA (ICH2)> port 0xcc40-0xcc7f,0xc800-0xc8ff irq 13 at device 31.5 on pci0
pcm1: <Analog Devices AD1885 AC97 Codec>
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on
acpi0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
sio1 port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
ppc0 port 0x778-0x77f,0x378-0x37f irq 7 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
orm0: <Option ROMs> at iomem 0xce800-0xcffff,0xc9000-0xce7ff,0xc0000-0xc8fff on isa0
pmtimer0 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via IOAPIC #0 intpin 2
Timecounters tick every 10.000 msec
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
ad0: 76293MB <IC35L080AVVA07-0> [155009/16/63] at ata0-master UDMA100
acd0: DVD-ROM <LITEON DVD-ROM LTD163> at ata1-master PIO4
Waiting 15 seconds for SCSI devices to settle
pcm1: measured ac97 link rate at 55921 Hz
SMP: AP CPU #1 Launched!
SMP: AP CPU #3 Launched!
SMP: AP CPU #2 Launched!
da0 at ahc0 bus 0 target 0 lun 0
da0: <SEAGATE ST336752LW 2212> Fixed Direct Access SCSI-3 device
da0: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing Enabled
da0: 34732MB (71132959 512 byte sectors: 255H 63S/T 4427C)
Mounting root from ufs:/dev/ad0s1a



Want to link to this message? Use this URL: <http://docs.FreeBSD.org/cgi/mid.cgi?000001c34e9b$e0d99880$2be86cc2>