From owner-freebsd-install Sat Apr 29 10:26:42 1995 Return-Path: install-owner Received: (from majordom@localhost) by freefall.cdrom.com (8.6.10/8.6.6) id KAA29782 for install-outgoing; Sat, 29 Apr 1995 10:26:42 -0700 Received: from galois.nscf.org (Galois.nscf.org [192.48.117.201]) by freefall.cdrom.com (8.6.10/8.6.6) with SMTP id KAA29773 for ; Sat, 29 Apr 1995 10:26:29 -0700 Received: by galois.nscf.org with UUCP (5.67/1.2) id AA19202; Sat, 29 Apr 95 12:35:23 -0400 Received: by wa4phy.ASYNC.COM (5.65/Smail2.5/02-15-88) id AA29189; Sat, 29 Apr 95 12:41:54 -0400 Received: (from bao@localhost) by saigon.async.com (8.6.11/8.6.9) id MAA00363; Sat, 29 Apr 1995 12:41:17 -0400 Date: Sat, 29 Apr 1995 12:41:17 -0400 (EDT) From: Bao Chau Ha To: questions@freebsd.org Cc: install@freebsd.org Subject: 950412-SNAP Installation with ESDI (WD1007V) System Message-Id: Mime-Version: 1.0 Content-Type: TEXT/PLAIN; charset=US-ASCII Sender: install-owner@freebsd.org Precedence: bulk How do I install 950412-SNAP on a system with a WD1007V ESDI controller and 2 drives: Maxtor XT4380E (320M) and Maxtor XT4760E (630M)? It is very annoying that the driver gets the true disk geometries directly from the ESDI controller and use them instead of the translated ones. It also ignores the spare sector mapping, so it does not help, even if I reformat my drives. Anyway, I did fdisk, added the translated geometry and was able to complete the installation from the boot and cpio floppies onto the first drive. Upon reboot, the kernel went up to the npx16 ... messages, then printed out a message about wrong size on partition d of wd1, which does not have a freebsd partition. It then panicked, and rebooted. Appreciate any helps, comments or suggestions. Thanks. Bao -- Bao Chau Ha (bao@saigon.async.com) Nuclear chemical engineer by day, Linux hacker by night and weekends. From owner-freebsd-install Sat Apr 29 15:12:51 1995 Return-Path: install-owner Received: (from majordom@localhost) by freefall.cdrom.com (8.6.10/8.6.6) id PAA19850 for install-outgoing; Sat, 29 Apr 1995 15:12:51 -0700 Received: from cs.weber.edu (cs.weber.edu [137.190.16.16]) by freefall.cdrom.com (8.6.10/8.6.6) with SMTP id PAA19844 ; Sat, 29 Apr 1995 15:12:48 -0700 Received: by cs.weber.edu (4.1/SMI-4.1.1) id AA29120; Sat, 29 Apr 95 16:06:07 MDT From: terry@cs.weber.edu (Terry Lambert) Message-Id: <9504292206.AA29120@cs.weber.edu> Subject: Re: 950412-SNAP Installation with ESDI (WD1007V) System To: bao@saigon.async.com (Bao Chau Ha) Date: Sat, 29 Apr 95 16:06:06 MDT Cc: questions@FreeBSD.org, install@FreeBSD.org In-Reply-To: from "Bao Chau Ha" at Apr 29, 95 12:41:17 pm X-Mailer: ELM [version 2.4dev PL52] Sender: install-owner@FreeBSD.org Precedence: bulk > How do I install 950412-SNAP on a system with a WD1007V > ESDI controller and 2 drives: Maxtor XT4380E (320M) and > Maxtor XT4760E (630M)? > > It is very annoying that the driver gets the true disk > geometries directly from the ESDI controller and use them > instead of the translated ones. It also ignores the > spare sector mapping, so it does not help, even if I > reformat my drives. The spare sector mapping and translation are software artifacts of the BIOS. If you are willing to port the VM86() code from NetBSD to FreeBSD and write BIOS based disk driver, you'd be a hero. Of course, this is difficult enough that the only OS out there that can do this at all right now is OS/2, so unless you are comparing the SNAP to the commercial release of OS/2, your complaint is not a valid one. It's like complaining because your car can't fly, and then arguing that this must be because it's a Ford instead of a Chevy... when in fact, checy doesn't manufacture flying cars either. > Anyway, I did fdisk, added the translated geometry and > was able to complete the installation from the boot > and cpio floppies onto the first drive. Upon reboot, > the kernel went up to the npx16 ... messages, then > printed out a message about wrong size on partition d > of wd1, which does not have a freebsd partition. It > then panicked, and rebooted. > Sounds like a Bad144 problem or errors early in the drive. If this is it, moving the partition up a cylinder will probably avoid the bad spot (it would have to be under the boot track or the disklabel). You may want to install a teeny DOS partition before installing the BSD -- some people have found this necessary with the new slice code in the most recent snaps. Terry Lambert terry@cs.weber.edu --- Any opinions in this posting are my own and not those of my present or previous employers.