Skip site navigation (1)Skip section navigation (2)
Date:      Sun, 10 Jan 2010 16:15:48 +0200
From:      Mikael Ikivesi <mikael@ikivesi.net>
To:        freebsd-acpi@freebsd.org
Subject:   resume problem with hp-laptop
Message-ID:  <201001101615.49012.mikael@ikivesi.net>

next in thread | raw e-mail | index | archive | help
Hello

My laptop has problems while resuming.
With setting: hw.acpi.reset_video=1
the laptop wakes up, and I can see messages on the screen.
About the time of ata reinit has been done the screen goes back to black, but 
system still remains operational. (ie. I can type commands and reboot cleanly)

While runnin X I can usually get system back and visible. Only strange thing 
is that systems seems faster (whole system is lot more responsive). I guess 
resuming somehow messes cpu frequency settings. (not visible in sysctl output)


Possible more useful information below:

----MESAGES AFTER ISSUING SUSPEND:
pci0:1:0:0: Transition from D0 to D3
pci0:8:0:0: Transition from D0 to D3
pci0:9:0:0: Transition from D0 to D3
fwohci0: fwohci_pci_suspend
pci0:10:0:0: Transition from D0 to D3
vga0: saving 68 bytes of video state
pci0:0:17:0: Transition from D0 to D3
pci0:0:18:2: Transition from D0 to D3
pci0:0:19:2: Transition from D0 to D3
ct_to_ts([2010-01-10 13:22:39]) = 1263129759.000000000
stray irq0
acpi0: suspend request ignored (not ready yet)
acpi0: request to enter state S5 failed (err 6)
pci0:0:18:2: Transition from D3 to D0
pci0:0:19:2: Transition from D3 to D0
re0: link state changed to DOWN
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: fwphy_rddata:: 0x5 loop=100, retry=100
fwohci0: fwphy_rddata:: 0x2 loop=100, retry=100
fwohci0: Link S400, max_rec 512 bytes.
fwohci0: max_rec 512 -> 2048
fwohci0: Initiate bus reset
fwohci0: fwphy_rddata:: 0x1 loop=100, retry=100
fwohci0: fwphy_rddata:: 0x1 loop=100, retry=100
ata2: reiniting channel ..
ata2: AHCI reset...
ata2: hardware reset ...
ata2: SATA connect time=10ms status=00000113
ata2: ready wait time=55ms
ata2: software reset port 15...
ata2: ahci_issue_cmd timeout: 3000 of 3000ms, status=00000001
ata2: port is not ready (timeout 0ms) tfd = 000001d0
ata2: software reset clear timeout
ata2: software reset port 0...
ata2: ready wait time=0ms
ata2: SIGNATURE: 00000101
ata2: AHCI reset done: devices=00000001
ugen1.2: <Broadcom Corp> at usbus1 (disconnected)
re0: link state changed to UP
ugen5.2: <AVerMedia> at usbus5 (disconnected)
ata2: reinit done ..
ata3: reiniting channel ..
ata3: AHCI reset...
ata3: hardware reset ...
ata3: SATA connect time=10ms status=00000113
ata3: ready wait time=0ms
ata3: software reset port 15...
ata3: ahci_issue_cmd timeout: 3000 of 3000ms, status=00000001
ata3: port is not ready (timeout 0ms) tfd = 00000180
ata3: software reset clear timeout
ata3: software reset port 0...
ata3: ready wait time=0ms
ata3: SIGNATURE: eb140101
ata3: AHCI reset done: devices=00010000
ata3: reinit done ..
ata4: reiniting channel ..
ata4: AHCI reset...
ata4: hardware reset ...
ata4: SATA connect timeout status=00000000
ata4: AHCI reset done: phy reset found no device
ata4: reinit done ..
ata5: reiniting channel ..
ata5: AHCI reset...
ata5: hardware reset ...
ata5: SATA connect timeout status=00000000
ata5: AHCI reset done: phy reset found no device
ata5: reinit done ..
ata6: reiniting channel ..
ata6: AHCI reset...
ata6: hardware reset ...
ata6: SATA connect timeout status=00000000
ata6: AHCI reset done: phy reset found no device
ata6: reinit done ..
ata7: reiniting channel ..
ata7: AHCI reset...
ata7: hardware reset ...
ata7: SATA connect timeout status=00000000
ata7: AHCI reset done: phy reset found no device
ata7: reinit done ..
usb_alloc_device:1586: set address 2 failed (USB_ERR_TIMEOUT, ignored)
ugen2.2: <Vimicro Co.,ltd> at usbus2 (disconnected)
ata0: reiniting channel ..
ata0: reset tp1 mask=00 ostat0=ff ostat1=ff
ata0: reinit done ..
ata1: reiniting channel ..
ata1: reset tp1 mask=03 ostat0=00 ostat1=00
ata1: stat0=0x00 err=0x00 lsb=0x00 msb=0x00
ata1: stat1=0x00 err=0x00 lsb=0x00 msb=0x00
ata1: reset tp2 stat0=00 stat1=00 devices=0x0
ata1: reinit done ..
battery0: battery initialization start
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
usb_alloc_device:1624: getting device descriptor at addr 2 failed, 
USB_ERR_TIMEOUT!
battery0: battery initialization done, tried 1 times
ugen1.2: <Broadcom Corp> at usbus1
ugen2.2: <Vimicro Co.,ltd> at usbus2
usbd_req_re_enumerate:1539: addr=2, set address failed! (USB_ERR_TIMEOUT, 
ignored)
usbd_req_re_enumerate:1553: getting device descriptor at addr 2 failed, 
USB_ERR_TIMEOUT!
usbd_req_re_enumerate:1539: addr=2, set address failed! (USB_ERR_TIMEOUT, 
ignored)
usbd_req_re_enumerate:1553: getting device descriptor at addr 2 failed, 
USB_ERR_TIMEOUT!
ugen5.2: <(null)> at usbus5 (disconnected)
uhub_reattach_port:435: could not allocate new device!
ugen5.2: <AVerMedia> at usbus5







------------------- DMESG BEFORE ISSUING SUSPEND
Copyright (c) 1992-2009 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.0-RELEASE #0: Sat Nov 21 15:02:08 UTC 2009
    root@mason.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
Preloaded elf kernel "/boot/kernel/kernel" at 0xffffffff80e19000.
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 2100095962 Hz
CPU: AMD Turion(tm) X2 Ultra Dual-Core Mobile ZM-80 (2100.10-MHz K8-class CPU)
  Origin = "AuthenticAMD"  Id = 0x200f31  Stepping = 1
  Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT>
  Features2=0x2001<SSE3,CX16>
  AMD Features=0xea500800<SYSCALL,NX,MMX+,FFXSR,RDTSCP,LM,3DNow!+,3DNow!>
  AMD Features2=0x131f<LAHF,CMP,SVM,ExtAPIC,CR8,Prefetch,OSVW,SKINIT>
  TSC: P-state invariant
L1 2MB data TLB: 8 entries, fully associative
L1 2MB instruction TLB: 8 entries, fully associative
L1 4KB data TLB: 32 entries, fully associative
L1 4KB instruction TLB: 32 entries, fully associative
L1 data cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
L1 instruction cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
L2 2MB unified TLB: 0 entries, disabled/not present
L2 4KB data TLB: 512 entries, 4-way associative
L2 4KB instruction TLB: 512 entries, 4-way associative
L2 unified cache: 1024 kbytes, 64 bytes/line, 1 lines/tag, 16-way associative
real memory  = 4294967296 (4096 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009bfff, 634880 bytes (155 pages)
0x0000000000e48000 - 0x00000000b66effff, 3045752832 bytes (743592 pages)
0x00000000bfdbf000 - 0x00000000bfe57fff, 626688 bytes (153 pages)
0x00000000bfebf000 - 0x00000000bfeecfff, 188416 bytes (46 pages)
0x00000000bfeff000 - 0x00000000bfefffff, 4096 bytes (1 pages)
0x0000000100000000 - 0x000000013ffeffff, 1073676288 bytes (262128 pages)
avail memory = 4097855488 (3908 MB)
ACPI APIC Table: <HP     3600    >
INTR: Adding local APIC 1 as a target
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
FreeBSD/SMP: 1 package(s) x 2 core(s)
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP): APIC ID:  1
APIC: CPU 0 has ACPI ID 0
APIC: CPU 1 has ACPI ID 1
ULE: setup cpu 0
ULE: setup cpu 1
ACPI: RSDP 0xfe020 00024 (v2 HP    )
ACPI: XSDT 0xbfefe120 0005C (v1 HPQOEM SLIC-MPC 00000003      01000013)
ACPI: FACP 0xbfefd000 000F4 (v4 HP     3600     00000003 MSFT 01000013)
ACPI: DSDT 0xbfef0000 096FA (v1 HP     3600     F0000000 MSFT 01000013)
ACPI: FACS 0xbfe61000 00040
ACPI: HPET 0xbfefc000 00038 (v1 HP     3600     00000001 MSFT 01000013)
ACPI: APIC 0xbfefb000 00084 (v2 HP     3600     00000001 MSFT 01000013)
ACPI: MCFG 0xbfefa000 0003C (v1 HP     3600     00000001 MSFT 01000013)
ACPI: BOOT 0xbfeef000 00028 (v1 HP     3600     00000001 MSFT 01000013)
ACPI: SLIC 0xbfeee000 00176 (v1 HPQOEM SLIC-MPC 06040000  LTP 00000001)
ACPI: SSDT 0xbfeed000 00386 (v1 AMD    PowerNow 00000001 AMD  00000001)
MADT: Found IO APIC ID 4, Interrupt 0 at 0xfec00000
ioapic0: Changing APIC ID to 4
ioapic0: Routing external 8259A's -> intpin 0
MADT: Interrupt override: source 0, irq 2
ioapic0: Routing IRQ 0 -> intpin 2
MADT: Interrupt override: source 9, irq 9
ioapic0: intpin 9 trigger: level
ioapic0: intpin 9 polarity: low
lapic0: Routing NMI -> LINT1
lapic0: LINT1 trigger: edge
lapic0: LINT1 polarity: high
lapic1: Routing NMI -> LINT1
lapic1: LINT1 trigger: edge
lapic1: LINT1 polarity: high
MADT: Ignoring local NMI routed to ACPI CPU 2
MADT: Ignoring local NMI routed to ACPI CPU 3
ioapic0 <Version 2.1> irqs 0-23 on motherboard
cpu0 BSP:
     ID: 0x00000000   VER: 0x80050010 LDR: 0x00000000 DFR: 0xffffffff
  lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
  timer: 0x000100ef therm: 0x00010000 err: 0x00010000 pcm: 0x00010400
wlan: <802.11 Link Layer>
null: <null device, zero device>
random: <entropy source, Software, Yarrow>
nfslock: pseudo-device
kbd: new array size 4
kbd1 at kbdmux0
mem: <memory>
io: <I/O>
hptrr: RocketRAID 17xx/2xxx SATA controller driver v1.2
acpi0: <HPQOEM SLIC-MPC> on motherboard
PCIe: Memory Mapped configuration base @ 0xe0000000
ioapic0: routing intpin 9 (ISA IRQ 9) to lapic 0 vector 48
acpi0: [MPSAFE]
acpi0: [ITHREAD]
AcpiOsDerivePciId: \\_SB_.PCI0.SMBS.IRQF -> bus 0 dev 20 func 0
acpi0: Power Button (fixed)
acpi0: wakeup code va 0xffffff800000f000 pa 0x4000
AcpiOsDerivePciId: \\_SB_.PCI0.NBBI -> bus 0 dev 0 func 0
AcpiOsDerivePciId: \\_SB_.PCI0.NBMS -> bus 0 dev 0 func 0
AcpiOsDerivePciId: \\_SB_.PCI0.NBBR -> bus 0 dev 0 func 0
AcpiOsDerivePciId: \\_SB_.PCI0.PB10.J380.PCFG -> bus 10 dev 0 func 0
ACPI timer: 1/2 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 -> 10
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
acpi_ec0: <Embedded Controller: GPE 0x3> port 0x62,0x66 on acpi0
pci_link0:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0  255   N     0  3 4 5 7 10 11 12 14 15
  Validation          0  255   N     0  3 4 5 7 10 11 12 14 15
  After Disable       0  255   N     0  3 4 5 7 10 11 12 14 15
pci_link1:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0  255   N     0  3 4 5 7 10 11 12 14 15
  Validation          0  255   N     0  3 4 5 7 10 11 12 14 15
  After Disable       0  255   N     0  3 4 5 7 10 11 12 14 15
pci_link2:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0  255   N     0  3 4 5 7 10 11 12 14 15
  Validation          0  255   N     0  3 4 5 7 10 11 12 14 15
  After Disable       0  255   N     0  3 4 5 7 10 11 12 14 15
pci_link3:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0  255   N     0  3 4 5 7 10 11 12 14 15
  Validation          0  255   N     0  3 4 5 7 10 11 12 14 15
  After Disable       0  255   N     0  3 4 5 7 10 11 12 14 15
pci_link4:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0  255   N     0  3 4 5 7 10 11 12 14 15
  Validation          0  255   N     0  3 4 5 7 10 11 12 14 15
  After Disable       0  255   N     0  3 4 5 7 10 11 12 14 15
pci_link5:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0  255   N     0  3 4 5 7 10 11 12 14 15
  Validation          0  255   N     0  3 4 5 7 10 11 12 14 15
  After Disable       0  255   N     0  3 4 5 7 10 11 12 14 15
pci_link6:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0  255   N     0  3 4 5 7 10 11 12 14 15
  Validation          0  255   N     0  3 4 5 7 10 11 12 14 15
  After Disable       0  255   N     0  3 4 5 7 10 11 12 14 15
pci_link7:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0  255   N     0  3 4 5 7 10 11 12 14 15
  Validation          0  255   N     0  3 4 5 7 10 11 12 14 15
  After Disable       0  255   N     0  3 4 5 7 10 11 12 14 15
acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
acpi_hpet0: vend: 0x4353 rev: 0x1 num: 3 hz: 14318180 opts: legacy_route
acpi_hpet0: HPET never increments, disabling
device_attach: acpi_hpet0 attach returned 6
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: domain=0, physical bus=0
found->	vendor=0x1022, dev=0x9600, revid=0x00
	domain=0, bus=0, slot=0, func=0
	class=06-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0006, statreg=0x2230, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1022, dev=0x9603, revid=0x00
	domain=0, bus=0, slot=2, func=0
	class=06-04-00, hdrtype=0x01, mfdev=0
	cmdreg=0x0007, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=255
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message
found->	vendor=0x1022, dev=0x9604, revid=0x00
	domain=0, bus=0, slot=4, func=0
	class=06-04-00, hdrtype=0x01, mfdev=0
	cmdreg=0x0007, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=255
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message
found->	vendor=0x1022, dev=0x9605, revid=0x00
	domain=0, bus=0, slot=5, func=0
	class=06-04-00, hdrtype=0x01, mfdev=0
	cmdreg=0x0007, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=255
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message
found->	vendor=0x1022, dev=0x9606, revid=0x00
	domain=0, bus=0, slot=6, func=0
	class=06-04-00, hdrtype=0x01, mfdev=0
	cmdreg=0x0007, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=255
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message
found->	vendor=0x1022, dev=0x9609, revid=0x00
	domain=0, bus=0, slot=10, func=0
	class=06-04-00, hdrtype=0x01, mfdev=0
	cmdreg=0x0007, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=255
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message
found->	vendor=0x1002, dev=0x4391, revid=0x00
	domain=0, bus=0, slot=17, func=0
	class=01-06-01, hdrtype=0x00, mfdev=0
	cmdreg=0x0007, statreg=0x0230, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=11
	powerspec 2  supports D0 D3  current D0
	map[10]: type I/O Port, range 32, base 0x6038, size  3, enabled
	map[14]: type I/O Port, range 32, base 0x604c, size  2, enabled
	map[18]: type I/O Port, range 32, base 0x6030, size  3, enabled
	map[1c]: type I/O Port, range 32, base 0x6048, size  2, enabled
	map[20]: type I/O Port, range 32, base 0x6010, size  4, enabled
	map[24]: type Memory, range 32, base 0xd2408000, size 10, enabled
pcib0: matched entry for 0.17.INTA
pcib0: slot 17 INTA hardwired to IRQ 22
found->	vendor=0x1002, dev=0x4397, revid=0x00
	domain=0, bus=0, slot=18, func=0
	class=0c-03-10, hdrtype=0x00, mfdev=1
	cmdreg=0x0017, statreg=0x02a0, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=4
	map[10]: type Memory, range 32, base 0xd2407000, size 12, enabled
pcib0: matched entry for 0.18.INTA
pcib0: slot 18 INTA hardwired to IRQ 16
found->	vendor=0x1002, dev=0x4398, revid=0x00
	domain=0, bus=0, slot=18, func=1
	class=0c-03-10, hdrtype=0x00, mfdev=0
	cmdreg=0x0017, statreg=0x02a0, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=4
	map[10]: type Memory, range 32, base 0xd2406000, size 12, enabled
pcib0: matched entry for 0.18.INTA
pcib0: slot 18 INTA hardwired to IRQ 16
found->	vendor=0x1002, dev=0x4396, revid=0x00
	domain=0, bus=0, slot=18, func=2
	class=0c-03-20, hdrtype=0x00, mfdev=0
	cmdreg=0x0017, statreg=0x02b0, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=5
	powerspec 2  supports D0 D1 D2 D3  current D0
	map[10]: type Memory, range 32, base 0xd2408500, size  8, enabled
pcib0: matched entry for 0.18.INTB
pcib0: slot 18 INTB hardwired to IRQ 17
found->	vendor=0x1002, dev=0x4397, revid=0x00
	domain=0, bus=0, slot=19, func=0
	class=0c-03-10, hdrtype=0x00, mfdev=1
	cmdreg=0x0017, statreg=0x02a0, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=10
	map[10]: type Memory, range 32, base 0xd2405000, size 12, enabled
pcib0: matched entry for 0.19.INTA
pcib0: slot 19 INTA hardwired to IRQ 18
found->	vendor=0x1002, dev=0x4398, revid=0x00
	domain=0, bus=0, slot=19, func=1
	class=0c-03-10, hdrtype=0x00, mfdev=0
	cmdreg=0x0017, statreg=0x02a0, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=10
	map[10]: type Memory, range 32, base 0xd2404000, size 12, enabled
pcib0: matched entry for 0.19.INTA
pcib0: slot 19 INTA hardwired to IRQ 18
found->	vendor=0x1002, dev=0x4396, revid=0x00
	domain=0, bus=0, slot=19, func=2
	class=0c-03-20, hdrtype=0x00, mfdev=0
	cmdreg=0x0017, statreg=0x02b0, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=7
	powerspec 2  supports D0 D1 D2 D3  current D0
	map[10]: type Memory, range 32, base 0xd2408400, size  8, enabled
pcib0: matched entry for 0.19.INTB
pcib0: slot 19 INTB hardwired to IRQ 19
found->	vendor=0x1002, dev=0x4385, revid=0x3a
	domain=0, bus=0, slot=20, func=0
	class=0c-05-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0403, statreg=0x9230, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1002, dev=0x439c, revid=0x00
	domain=0, bus=0, slot=20, func=1
	class=01-01-8a, hdrtype=0x00, mfdev=0
	cmdreg=0x0015, statreg=0x0230, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=4
	MSI supports 1 message
	map[20]: type I/O Port, range 32, base 0x6000, size  4, enabled
pcib0: matched entry for 0.20.INTA
pcib0: slot 20 INTA hardwired to IRQ 16
found->	vendor=0x1002, dev=0x4383, revid=0x00
	domain=0, bus=0, slot=20, func=2
	class=04-03-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0006, statreg=0x0410, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=4
	powerspec 2  supports D0 D3  current D0
	map[10]: type Memory, range 64, base 0xd2400000, size 14, enabled
pcib0: matched entry for 0.20.INTA
pcib0: slot 20 INTA hardwired to IRQ 16
found->	vendor=0x1002, dev=0x439d, revid=0x00
	domain=0, bus=0, slot=20, func=3
	class=06-01-00, hdrtype=0x00, mfdev=1
	cmdreg=0x000f, statreg=0x0220, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1002, dev=0x4384, revid=0x00
	domain=0, bus=0, slot=20, func=4
	class=06-04-01, hdrtype=0x01, mfdev=1
	cmdreg=0x0007, statreg=0x02a0, cachelnsz=0 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1022, dev=0x1300, revid=0x40
	domain=0, bus=0, slot=24, func=0
	class=06-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0000, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1022, dev=0x1301, revid=0x00
	domain=0, bus=0, slot=24, func=1
	class=06-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1022, dev=0x1302, revid=0x00
	domain=0, bus=0, slot=24, func=2
	class=06-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1022, dev=0x1303, revid=0x00
	domain=0, bus=0, slot=24, func=3
	class=06-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0000, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1022, dev=0x1304, revid=0x00
	domain=0, bus=0, slot=24, func=4
	class=06-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
pcib1: <ACPI PCI-PCI bridge> at device 2.0 on pci0
pcib1:   domain            0
pcib1:   secondary bus     1
pcib1:   subordinate bus   1
pcib1:   I/O decode        0x5000-0x5fff
pcib1:   memory decode     0xd2300000-0xd23fffff
pcib1:   prefetched decode 0xc0000000-0xcfffffff
pci1: <ACPI PCI bus> on pcib1
pci1: domain=0, physical bus=1
found->	vendor=0x1002, dev=0x95c4, revid=0x00
	domain=0, bus=1, slot=0, func=0
	class=03-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0007, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=10
	powerspec 3  supports D0 D1 D2 D3  current D0
	MSI supports 1 message, 64 bit
	map[10]: type Prefetchable Memory, range 32, base 0xc0000000, size 28, 
enabled
pcib1: requested memory range 0xc0000000-0xcfffffff: good
	map[14]: type I/O Port, range 32, base 0x5000, size  8, enabled
pcib1: requested I/O range 0x5000-0x50ff: in range
	map[18]: type Memory, range 32, base 0xd2300000, size 16, enabled
pcib1: requested memory range 0xd2300000-0xd230ffff: good
pcib1: matched entry for 1.0.INTA
pcib1: slot 0 INTA hardwired to IRQ 18
found->	vendor=0x1002, dev=0xaa28, revid=0x00
	domain=0, bus=1, slot=0, func=1
	class=04-03-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0007, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=7
	powerspec 3  supports D0 D1 D2 D3  current D0
	MSI supports 1 message, 64 bit
	map[10]: type Memory, range 32, base 0xd2310000, size 14, enabled
pcib1: requested memory range 0xd2310000-0xd2313fff: good
pcib1: matched entry for 1.0.INTB
pcib1: slot 0 INTB hardwired to IRQ 19
vgapci0: <VGA-compatible display> port 0x5000-0x50ff mem 
0xc0000000-0xcfffffff,0xd2300000-0xd230ffff irq 18 at device 0.0 on pci1
pci1: <multimedia, HDA> at device 0.1 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> at device 4.0 on pci0
pcib2:   domain            0
pcib2:   secondary bus     2
pcib2:   subordinate bus   7
pcib2:   I/O decode        0x3000-0x4fff
pcib2:   memory decode     0xd1300000-0xd22fffff
pcib2:   prefetched decode 0xd0000000-0xd0ffffff
pci2: <ACPI PCI bus> on pcib2
pci2: domain=0, physical bus=2
pcib3: <ACPI PCI-PCI bridge> at device 5.0 on pci0
pcib3:   domain            0
pcib3:   secondary bus     8
pcib3:   subordinate bus   8
pcib3:   I/O decode        0xfffff000-0xfff
pcib3:   memory decode     0xd1200000-0xd12fffff
pcib3:   no prefetched decode
pci8: <ACPI PCI bus> on pcib3
pci8: domain=0, physical bus=8
found->	vendor=0x168c, dev=0x002a, revid=0x01
	domain=0, bus=8, slot=0, func=0
	class=02-80-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0007, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=5
	powerspec 2  supports D0 D1 D3  current D0
	MSI supports 1 message
	MSI-X supports 1 message in map 0x10
	map[10]: type Memory, range 64, base 0xd1200000, size 16, enabled
pcib3: requested memory range 0xd1200000-0xd120ffff: good
pcib3: matched entry for 8.0.INTA
pcib3: slot 0 INTA hardwired to IRQ 17
ath0: <Atheros 9280> mem 0xd1200000-0xd120ffff irq 17 at device 0.0 on pci8
ath0: Reserved 0x10000 bytes for rid 0x10 type 3 at 0xd1200000
ioapic0: routing intpin 17 (PCI IRQ 17) to lapic 0 vector 49
ath0: [MPSAFE]
ath0: [ITHREAD]
ath0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
ath0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
ath0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 
36Mbps 48Mbps 54Mbps
ath0: 11na MCS: 15Mbps 30Mbps 45Mbps 60Mbps 90Mbps 120Mbps 135Mbps 150Mbps 
30Mbps 60Mbps 90Mbps 120Mbps 180Mbps 240Mbps 270Mbps 300Mbps
ath0: 11ng MCS: 15Mbps 30Mbps 45Mbps 60Mbps 90Mbps 120Mbps 135Mbps 150Mbps 
30Mbps 60Mbps 90Mbps 120Mbps 180Mbps 240Mbps 270Mbps 300Mbps
ath0: AR9280 mac 128.2 RF5133 phy 13.0
ath0: Use hw queue 1 for WME_AC_BE traffic
ath0: Use hw queue 0 for WME_AC_BK traffic
ath0: Use hw queue 2 for WME_AC_VI traffic
ath0: Use hw queue 3 for WME_AC_VO traffic
ath0: Use hw queue 8 for CAB traffic
ath0: Use hw queue 9 for beacons
pcib4: <ACPI PCI-PCI bridge> at device 6.0 on pci0
pcib4:   domain            0
pcib4:   secondary bus     9
pcib4:   subordinate bus   9
pcib4:   I/O decode        0x2000-0x2fff
pcib4:   prefetched decode 0xd1000000-0xd10fffff
pci9: <ACPI PCI bus> on pcib4
pci9: domain=0, physical bus=9
found->	vendor=0x10ec, dev=0x8168, revid=0x02
	domain=0, bus=9, slot=0, func=0
	class=02-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0007, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=10
	powerspec 3  supports D0 D1 D2 D3  current D0
	MSI supports 2 messages, 64 bit
	MSI-X supports 2 messages in map 0x20
	map[10]: type I/O Port, range 32, base 0x2000, size  8, enabled
pcib4: requested I/O range 0x2000-0x20ff: in range
	map[18]: type Prefetchable Memory, range 64, base 0xd1010000, size 12, 
enabled
pcib4: requested memory range 0xd1010000-0xd1010fff: good
	map[20]: type Prefetchable Memory, range 64, base 0xd1000000, size 16, 
enabled
pcib4: requested memory range 0xd1000000-0xd100ffff: good
pcib4: matched entry for 9.0.INTA
pcib4: slot 0 INTA hardwired to IRQ 18
re0: <RealTek 8168/8168B/8168C/8168CP/8168D/8168DP/8111B/8111C/8111CP/8111DP 
PCIe Gigabit Ethernet> port 0x2000-0x20ff mem 
0xd1010000-0xd1010fff,0xd1000000-0xd100ffff irq 18 at device 0.0 on pci9
re0: Reserved 0x1000 bytes for rid 0x18 type 3 at 0xd1010000
re0: MSI count : 2
re0: attempting to allocate 1 MSI vectors (2 supported)
msi: routing MSI IRQ 256 to local APIC 0 vector 50
re0: using IRQ 256 for MSI
re0: Using 1 MSI messages
re0: Chip rev. 0x3c000000
re0: MAC rev. 0x00400000
miibus0: <MII bus> on re0
rgephy0: <RTL8169S/8110S/8211B media interface> PHY 1 on miibus0
rgephy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
re0: bpf attached
re0: Ethernet address: 00:1e:68:9c:41:09
re0: [MPSAFE]
re0: [FILTER]
pcib5: <ACPI PCI-PCI bridge> at device 10.0 on pci0
pcib5:   domain            0
pcib5:   secondary bus     10
pcib5:   subordinate bus   10
pcib5:   I/O decode        0xfffff000-0xfff
pcib5:   memory decode     0xd1100000-0xd11fffff
pcib5:   no prefetched decode
pci10: <ACPI PCI bus> on pcib5
pci10: domain=0, physical bus=10
found->	vendor=0x197b, dev=0x2380, revid=0x00
	domain=0, bus=10, slot=0, func=0
	class=0c-00-10, hdrtype=0x00, mfdev=1
	cmdreg=0x0007, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=10
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message
	map[10]: type Memory, range 32, base 0xd1100000, size 11, enabled
pcib5: requested memory range 0xd1100000-0xd11007ff: good
	map[14]: type Memory, range 32, base 0xd1100d00, size  7, enabled
pcib5: requested memory range 0xd1100d00-0xd1100d7f: good
	map[20]: type Memory, range 32, base 0xd1100c80, size  7, enabled
pcib5: requested memory range 0xd1100c80-0xd1100cff: good
	map[24]: type Memory, range 32, base 0xd1100c00, size  7, enabled
pcib5: requested memory range 0xd1100c00-0xd1100c7f: good
pcib5: matched entry for 10.0.INTA
pcib5: slot 0 INTA hardwired to IRQ 18
found->	vendor=0x197b, dev=0x2382, revid=0x00
	domain=0, bus=10, slot=0, func=1
	class=08-80-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0007, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=10
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message
	map[10]: type Memory, range 32, base 0xd1100b00, size  8, enabled
pcib5: requested memory range 0xd1100b00-0xd1100bff: good
pcib5: matched entry for 10.0.INTA
pcib5: slot 0 INTA hardwired to IRQ 18
found->	vendor=0x197b, dev=0x2381, revid=0x00
	domain=0, bus=10, slot=0, func=2
	class=08-05-01, hdrtype=0x00, mfdev=1
	cmdreg=0x0007, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=10
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message
	map[10]: type Memory, range 32, base 0xd1100a00, size  8, enabled
pcib5: requested memory range 0xd1100a00-0xd1100aff: good
pcib5: matched entry for 10.0.INTA
pcib5: slot 0 INTA hardwired to IRQ 18
found->	vendor=0x197b, dev=0x2383, revid=0x00
	domain=0, bus=10, slot=0, func=3
	class=08-80-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0007, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=10
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message
	map[10]: type Memory, range 32, base 0xd1100900, size  8, enabled
pcib5: requested memory range 0xd1100900-0xd11009ff: good
pcib5: matched entry for 10.0.INTA
pcib5: slot 0 INTA hardwired to IRQ 18
found->	vendor=0x197b, dev=0x2384, revid=0x00
	domain=0, bus=10, slot=0, func=4
	class=08-80-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0007, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=10
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message
	map[10]: type Memory, range 32, base 0xd1100800, size  8, enabled
pcib5: requested memory range 0xd1100800-0xd11008ff: good
pcib5: matched entry for 10.0.INTA
pcib5: slot 0 INTA hardwired to IRQ 18
fwohci0: vendor=197b, dev=2380
fwohci0: vendor=197b, dev=2380
fwohci0: <1394 Open Host Controller Interface> mem 
0xd1100000-0xd11007ff,0xd1100d00-0xd1100d7f,0xd1100c80-0xd1100cff,0xd1100c00-0xd1100c7f 
irq 18 at device 0.0 on pci10
fwohci0: Reserved 0x800 bytes for rid 0x10 type 3 at 0xd1100000
ioapic0: routing intpin 18 (PCI IRQ 18) to lapic 0 vector 51
fwohci0: [MPSAFE]
fwohci0: [ITHREAD]
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:24:1b:00:c9:39:19:01
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: fwphy_rddata:: 0x5 loop=100, retry=100
fwohci0: fwphy_rddata:: 0x2 loop=100, retry=100
fwohci0: Link S400, max_rec 512 bytes.
fwohci0: max_rec 512 -> 2048
firewire0: <IEEE1394(FireWire) bus> on fwohci0
dcons_crom0: <dcons configuration ROM> on firewire0
dcons_crom0: bus_addr 0x158c000
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:24:1b:39:19:01
fwe0: bpf attached
fwe0: Ethernet address: 02:24:1b:39:19:01
fwip0: <IP over FireWire> on firewire0
fwip0: bpf attached
fwip0: Firewire address: 00:24:1b:00:c9:39:19:01 @ 0xfffe00000000, S400, maxrec 
2048
fwohci0: Initiate bus reset
fwohci0: fwphy_rddata:: 0x1 loop=100, retry=100
fwohci0: fwphy_rddata:: 0x1 loop=100, retry=100
pci10: <base peripheral> at device 0.1 (no driver attached)
pci10: <base peripheral, SD host controller> at device 0.2 (no driver 
attached)
pci10: <base peripheral> at device 0.3 (no driver attached)
pci10: <base peripheral> at device 0.4 (no driver attached)
atapci0: <ATI IXP700/800 SATA300 controller> port 
0x6038-0x603f,0x604c-0x604f,0x6030-0x6037,0x6048-0x604b,0x6010-0x601f mem 
0xd2408000-0xd24083ff irq 22 at device 17.0 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0x6010
atapci0: Reserved 0x400 bytes for rid 0x24 type 3 at 0xd2408000
ioapic0: routing intpin 22 (PCI IRQ 22) to lapic 0 vector 52
atapci0: [MPSAFE]
atapci0: [ITHREAD]
atapci0: AHCI v1.10 controller with 6 3Gbps ports, PM supported
atapci0: Caps: 64bit NCQ SNTF MPS AL CLO 3Gbps PM PMD 32cmd CCC 6ports
ata2: <ATA channel 0> on atapci0
ata2: AHCI reset...
ata2: hardware reset ...
ata2: SATA connect time=10ms status=00000113
ata2: ready wait time=356ms
ata2: software reset port 15...
ata2: ahci_issue_cmd timeout: 3000 of 3000ms, status=00000001
ata2: port is not ready (timeout 0ms) tfd = 000001d0
ata2: software reset clear timeout
ata2: software reset port 0...
ata2: ready wait time=0ms
ata2: SIGNATURE: 00000101
ata2: AHCI reset done: devices=00000001
ata2: [MPSAFE]
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci0
ata3: AHCI reset...
ata3: hardware reset ...
ata3: SATA connect time=10ms status=00000113
ata3: ready wait time=0ms
ata3: software reset port 15...
ata3: ahci_issue_cmd timeout: 3000 of 3000ms, status=00000001
ata3: port is not ready (timeout 0ms) tfd = 00000180
ata3: software reset clear timeout
ata3: software reset port 0...
ata3: ready wait time=0ms
ata3: SIGNATURE: eb140101
ata3: AHCI reset done: devices=00010000
ata3: [MPSAFE]
ata3: [ITHREAD]
ata4: <ATA channel 2> on atapci0
ata4: AHCI reset...
ata4: hardware reset ...
ata4: SATA connect timeout status=00000000
ata4: AHCI reset done: phy reset found no device
ata4: [MPSAFE]
ata4: [ITHREAD]
ata5: <ATA channel 3> on atapci0
ata5: AHCI reset...
ata5: hardware reset ...
ata5: SATA connect timeout status=00000000
ata5: AHCI reset done: phy reset found no device
ata5: [MPSAFE]
ata5: [ITHREAD]
ata6: <ATA channel 4> on atapci0
ata6: AHCI reset...
ata6: hardware reset ...
ata6: SATA connect timeout status=00000000
ata6: AHCI reset done: phy reset found no device
ata6: [MPSAFE]
ata6: [ITHREAD]
ata7: <ATA channel 5> on atapci0
ata7: AHCI reset...
ata7: hardware reset ...
ata7: SATA connect timeout status=00000000
ata7: AHCI reset done: phy reset found no device
ata7: [MPSAFE]
ata7: [ITHREAD]
ohci0: <OHCI (generic) USB controller> mem 0xd2407000-0xd2407fff irq 16 at 
device 18.0 on pci0
ohci0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xd2407000
ioapic0: routing intpin 16 (PCI IRQ 16) to lapic 0 vector 53
ohci0: [MPSAFE]
ohci0: [ITHREAD]
usbus0: <OHCI (generic) USB controller> on ohci0
ohci1: <OHCI (generic) USB controller> mem 0xd2406000-0xd2406fff irq 16 at 
device 18.1 on pci0
ohci1: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xd2406000
ohci1: [MPSAFE]
ohci1: [ITHREAD]
usbus1: <OHCI (generic) USB controller> on ohci1
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xd2408500-0xd24085ff irq 17 at 
device 18.2 on pci0
ehci0: Reserved 0x100 bytes for rid 0x10 type 3 at 0xd2408500
ehci0: [MPSAFE]
ehci0: [ITHREAD]
usbus2: waiting for BIOS to give up control
usbus2: EHCI version 1.0
usbus2: <EHCI (generic) USB 2.0 controller> on ehci0
ohci2: <OHCI (generic) USB controller> mem 0xd2405000-0xd2405fff irq 18 at 
device 19.0 on pci0
ohci2: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xd2405000
ohci2: [MPSAFE]
ohci2: [ITHREAD]
usbus3: <OHCI (generic) USB controller> on ohci2
ohci3: <OHCI (generic) USB controller> mem 0xd2404000-0xd2404fff irq 18 at 
device 19.1 on pci0
ohci3: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xd2404000
ohci3: [MPSAFE]
ohci3: [ITHREAD]
usbus4: <OHCI (generic) USB controller> on ohci3
ehci1: <EHCI (generic) USB 2.0 controller> mem 0xd2408400-0xd24084ff irq 19 at 
device 19.2 on pci0
ehci1: Reserved 0x100 bytes for rid 0x10 type 3 at 0xd2408400
ioapic0: routing intpin 19 (PCI IRQ 19) to lapic 0 vector 54
ehci1: [MPSAFE]
ehci1: [ITHREAD]
usbus5: waiting for BIOS to give up control
usbus5: EHCI version 1.0
usbus5: <EHCI (generic) USB 2.0 controller> on ehci1
pci0: <serial bus, SMBus> at device 20.0 (no driver attached)
atapci1: <ATI IXP700/800 UDMA133 controller> port 
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x6000-0x600f irq 16 at device 20.1 on 
pci0
atapci1: Reserved 0x10 bytes for rid 0x20 type 4 at 0x6000
ata0: <ATA channel 0> on atapci1
atapci1: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci1: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=00 ostat0=ff ostat1=ff
ioapic0: routing intpin 14 (ISA IRQ 14) to lapic 0 vector 55
ata0: [MPSAFE]
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci1
atapci1: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci1: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=03 ostat0=00 ostat1=00
ata1: stat0=0x00 err=0x00 lsb=0x00 msb=0x00
ata1: stat1=0x00 err=0x00 lsb=0x00 msb=0x00
ata1: reset tp2 stat0=00 stat1=00 devices=0x0
ioapic0: routing intpin 15 (ISA IRQ 15) to lapic 0 vector 56
ata1: [MPSAFE]
ata1: [ITHREAD]
pci0: <multimedia, HDA> at device 20.2 (no driver attached)
isab0: <PCI-ISA bridge> at device 20.3 on pci0
isa0: <ISA bus> on isab0
pcib6: <ACPI PCI-PCI bridge> at device 20.4 on pci0
pcib6:   domain            0
pcib6:   secondary bus     128
pcib6:   subordinate bus   143
pcib6:   I/O decode        0x1000-0x1fff
pcib6:   no prefetched decode
pcib6:   Subtractively decoded bridge.
pci128: <ACPI PCI bus> on pcib6
pci128: domain=0, physical bus=128
battery0: <ACPI Control Method Battery> on acpi0
acpi_acad0: <AC Adapter> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
acpi_tz0: _CRT value is absurd, ignored (-273.2C)
atrtc0: <AT realtime clock> port 0x70-0x71 on acpi0
atrtc0: registered as a time-of-day clock (resolution 1000000us)
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0067
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
ioapic0: routing intpin 1 (ISA IRQ 1) to lapic 0 vector 57
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: unable to allocate IRQ
psmcpnp0: <PS/2 mouse port> irq 12 on acpi0
psm0: current command byte:0067
psm0: <PS/2 Mouse> irq 12 on atkbdc0
ioapic0: routing intpin 12 (ISA IRQ 12) to lapic 0 vector 58
psm0: [GIANT-LOCKED]
psm0: [ITHREAD]
psm0: model Generic PS/2 mouse, device ID 0-00, 2 buttons
psm0: config:00000000, flags:00000008, packet size:3
psm0: syncmask:c0, syncbits:00
cpu0: <ACPI CPU> on acpi0
cpu0: switching to generic Cx mode
acpi_throttle0: <ACPI CPU Throttling> on cpu0
acpi_throttle0: P_CNT from P_BLK 0x410
hwpstate0: <Cool`n'Quiet 2.0> on cpu0
cpu1: <ACPI CPU> on acpi0
acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
acpi_hpet0: vend: 0x4353 rev: 0x1 num: 3 hz: 14318180 opts: legacy_route
Timecounter "HPET" frequency 14318180 Hz quality 900
ahc_isa_probe 0: ioport 0xc00 alloc failed
ex_isa_identify()
isa_probe_children: disabling PnP devices
atkbdc: atkbdc0 already exists; skipping it
atrtc: atrtc0 already exists; skipping it
sc: sc0 already exists; skipping it
isa_probe_children: probing non-PnP devices
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd1, terminal emulator: scteken (teken terminal)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fdc0 failed to probe at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
ppc0: cannot reserve I/O port range
ppc0: <Parallel port> failed to probe at irq 7 on isa0
uart0: <ns8250> failed to probe at port 0x3f8-0x3ff irq 4 on isa0
uart1: <ns8250> failed to probe at port 0x2f8-0x2ff irq 3 on isa0
isa_probe_children: probing PnP devices
Device configuration finished.
Reducing kern.maxvnodes 257682 -> 100000
procfs registered
lapic: Divisor 2, Frequency 100004602 hz
Timecounter "TSC" frequency 2100095962 Hz quality -100
Timecounters tick every 1.000 msec
lo0: bpf attached
hptrr: no controller detected.
ata0: Identifying devices: 00000000
ata0: New devices: 00000000
ata1: Identifying devices: 00000000
ata1: New devices: 00000000
ata2: Identifying devices: 00000001
ata2: New devices: 00000001
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 480Mbps High Speed USB v2.0
usbus3: 12Mbps Full Speed USB v1.0
usbus4: 12Mbps Full Speed USB v1.0
usbus5: 480Mbps High Speed USB v2.0
battery0: battery initialization start
acpi_acad0: acline initialization start
ata2-master: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=40 wire
ad4: 305245MB <WDC WD3200BEVS-60VAT0 12.01A12> at ata2-master SATA150
ad4: 625142448 sectors [620181C/16H/63S] 16 sectors/interrupt 1 depth queue
GEOM: new disk ad4
acpi_acad0: On Line
acpi_acad0: acline initialization done, tried 1 times
ugen0.1: <ATI> at usbus0
uhub0: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <ATI> at usbus1
uhub1: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen2.1: <ATI> at usbus2
uhub2: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2
ugen3.1: <ATI> at usbus3
uhub3: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
ugen4.1: <ATI> at usbus4
uhub4: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4
ugen5.1: <ATI> at usbus5
uhub5: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus5
battery0: battery initialization done, tried 1 times
uhub0: 3 ports with 3 removable, self powered
uhub1: 3 ports with 3 removable, self powered
uhub3: 3 ports with 3 removable, self powered
uhub4: 3 ports with 3 removable, self powered
ad4: Silicon Image check1 failed
ad4: Adaptec check1 failed
ad4: LSI (v3) check1 failed
ad4: LSI (v2) check1 failed
ad4: FreeBSD check1 failed
ata3: Identifying devices: 00010000
ata3: New devices: 00010000
ata3-master: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=40 wire
ata3: device_reset timeout=1690us
acd0: <TSSTcorp CDDVDW TS-L633L/0400> DVDR drive at ata3 as master
acd0: read 8115KB/s (10820KB/s) write 172KB/s, 2048KB buffer, SATA150
acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, DVDRAM, packet
acd0: Writes: CDR, CDRW, DVDR, DVDRAM, test write, burnproof
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: DVD 120mm data disc
ata4: Identifying devices: 00000000
ata4: New devices: 00000000
ata5: Identifying devices: 00000000
ata5: New devices: 00000000
ata6: Identifying devices: 00000000
ata6: New devices: 00000000
ata7: Identifying devices: 00000000
ata7: New devices: 00000000
ATA PseudoRAID loaded
SMP: AP CPU #1 Launched!
cpu1 AP:
     ID: 0x01000000   VER: 0x80050010 LDR: 0x00000000 DFR: 0xffffffff
  lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
  timer: 0x000200ef therm: 0x00010000 err: 0x00010000 pcm: 0x00010400
ioapic0: routing intpin 9 (ISA IRQ 9) to lapic 1 vector 48
ioapic0: routing intpin 14 (ISA IRQ 14) to lapic 1 vector 49
ioapic0: routing intpin 16 (PCI IRQ 16) to lapic 1 vector 50
ioapic0: routing intpin 18 (PCI IRQ 18) to lapic 1 vector 51
ioapic0: routing intpin 22 (PCI IRQ 22) to lapic 1 vector 52
uhub2: 6 ports with 6 removable, self powered
uhub5: 6 ports with 6 removable, self powered
ugen5.2: <AVerMedia> at usbus5
ugen2.2: <Vimicro Co.,ltd> at usbus2
ugen1.2: <Broadcom Corp> at usbus1
Trying to mount root from ufs:/dev/ad4s3a
ct_to_ts([2010-01-10 13:20:56]) = 1263129656.000000000
start_init: trying /sbin/init
re0: link state changed to UP
re0: link state changed to DOWN
re0: link state changed to UP
re0: link state changed to DOWN
re0: link state changed to UP




--------
Mikael Ikivesi (mikael [at] ikivesi.net)
http://taotao.fi
http://kiinalainenlaaketiede.fi



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?201001101615.49012.mikael>