Date: Wed, 27 Aug 2008 15:33:43 -0700 From: Mark Atkinson <atkin901@yahoo.com> To: freebsd-current@freebsd.org Subject: Re: xpt_config panic: run_interrupt_driven_config_hooks: waited too long Message-ID: <g94ko8$8v4$1@ger.gmane.org> References: <g94i65$3p2$1@ger.gmane.org> <alpine.BSF.1.10.0808272314570.62435@fledge.watson.org>
next in thread | previous in thread | raw e-mail | index | archive | help
Robert Watson wrote: > On Wed, 27 Aug 2008, Mark Atkinson wrote: > >> I have two hp dl380's (xeon p4s with ciss) that cannot boot recent >> GENERIC kernels from -current. > > In 6.x, I take it there's also not a long delay at this point in the boot? > In 7.x/8.x the timeout messages and panic are intended to debug apparent > hangs in the boot, but if it's simply the case that we should wait 20 > seconds longer fo > things to work out, we can do that. On the other hand, if it booted just > fine in 6.x without any delay there, that was exactly the sort of problem > this diagnostic was intended to help debug. :-) Both 6.x and the June 11th -current there is no noticeable delay at this point. The July bootonly.iso hangs indefinitely at the same point in the kernel boot as -current from today (I don't think I waited 5 minutes for the timeout but assumed it was hung at this point). >> run_interrupt_driven_hooks: still waiting after 60 seconds for xpt_config >> run_interrupt_driven_hooks: still waiting after 120 seconds for >> xpt_config run_interrupt_driven_hooks: still waiting after 180 seconds >> for xpt_config run_interrupt_driven_hooks: still waiting after 240 >> seconds for xpt_config run_interrupt_driven_hooks: still waiting after >> 300 seconds for xpt_config panic: run_interrupt_driven_config_hooks: >> waited too long cpuid = 0 >> KDB: enter: panic >> [thread pid 0 tid 100000 ] >> Stopped at kdb_enter+0x3a: movl $0,kdb_why >> db> bt >> Tracing pid 0 tid 100000 td 0xc0caa020 >> kdb_enter(c0b68e3a,c0b68e3a,c0b6b277,c1020d08,0,...) at kdb_enter+0x3a >> panic(c0b6b277,0,c0b6b20e,71,ea60,...) at panic+0x12e >> run_interrupt_driven_config_hooks(0,101ec00,101ec00,101e000,1025000,...) >> at run_interrupt_driven_config_hooks+0x1db >> mi_startup() at mi_startup+0xa6 >> begin() at begin+0x2c >> db> show conifhk >> hook: 0xc0473080 at xpt_config+0 arg: 0 >> >> >> In 6.2-RELEASE, this is what I do get when booting at this point in the >> kernel: >> >> ciss0: command status 0x1 (target status) scsi status 0x2 >> (probe0:ciss0:0:0:0): error 22 >> (probe0:ciss0:0:0:0): Unretryable Error >> ciss0: command status 0x1 (target status) scsi status 0x2 >> (probe0:ciss0:0:0:0): error 22 >> (probe0:ciss0:0:0:0): Unretryable Error >> pass0 at ciss0 bus 0 target 0 lun 0 >> pass0: <COMPAQ RAID 0 VOLUME OK> Fixed Direct Access SCSI-0 device >> pass0: 135.168MB/s transfers >> da0 at ciss0 bus 0 target 0 lun 0 >> da0: <COMPAQ RAID 0 VOLUME OK> Fixed Direct Access SCSI-0 device >> da0: 135.168MB/s transfers >> da0: 69455MB (142245120 512 byte sectors: 255H 32S/T 17432C) >> GEOM: new disk da0 >> >> Full 8-current verbose output boot: >> >> >> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 >> The Regents of the University of California. All rights reserved. >> FreeBSD is a registered trademark of The FreeBSD Foundation. >> FreeBSD 8.0-CURRENT #0: Wed Aug 27 13:05:01 PDT 2008 >> root@dl380-1.f5test.net:/usr/obj/usr/src/sys/DL380 >> WARNING: WITNESS option enabled, expect reduced performance. >> Preloaded elf kernel "/boot/kernel/kernel" at 0xc0fdb000. >> Preloaded elf module "/boot/kernel/acpi.ko" at 0xc0fdb198. >> Timecounter "i8254" frequency 1193182 Hz quality 0 >> Calibrating TSC clock ... TSC clock: 3185522100 Hz >> CPU: Intel(R) Xeon(TM) CPU 3.20GHz (3185.52-MHz 686-class CPU) >> Origin = "GenuineIntel" Id = 0xf25 Stepping = 5 >> >> Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> >> Features2=0x4400<CNXT-ID,xTPR> >> Logical CPUs per core: 2 >> >> Instruction TLB: 4 KB, 2 MB or 4 MB pages, fully associative, 64 entries >> Data TLB: 4 KB or 4 MB pages, fully associative, 64 entries >> 1st-level data cache: 8 KB, 4-way set associative, sectored cache, 64 >> byte line size >> 3rd-level cache: 1 MB, 8-way set associative, sectored cache, 64 byte >> line size >> Trace cache: 12K-uops, 8-way set associative >> 2nd-level cache: 512 KB, 8-way set associative, sectored cache, 64 byte >> line size >> real memory = 1073717248 (1023 MB) >> Physical memory chunk(s): >> 0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages) >> 0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages) >> 0x0000000001025000 - 0x000000003eeaefff, 1038655488 bytes (253578 pages) >> avail memory = 1038020608 (989 MB) >> Table 'FACP' at 0x3fffa040 >> Table 'APIC' at 0x3fffa100 >> MADT: Found table at 0x3fffa100 >> MP Configuration Table version 1.4 found at 0xc00f29ca >> APIC: Using the MADT enumerator. >> MADT: Found CPU APIC ID 0 ACPI ID 0: disabled >> MADT: Found CPU APIC ID 2 ACPI ID 2: disabled >> MADT: Found CPU APIC ID 4 ACPI ID 4: disabled >> MADT: Found CPU APIC ID 6 ACPI ID 6: enabled >> SMP: Added CPU 6 (AP) >> MADT: Found CPU APIC ID 1 ACPI ID 1: disabled >> MADT: Found CPU APIC ID 3 ACPI ID 3: disabled >> MADT: Found CPU APIC ID 5 ACPI ID 5: disabled >> MADT: Found CPU APIC ID 7 ACPI ID 7: disabled >> ACPI APIC Table: <COMPAQ 00000083> >> bios32: Found BIOS32 Service Directory header at 0xc00ffee0 >> bios32: Entry = 0xf0000 (c00f0000) Rev = 0 Len = 1 >> pcibios: PCI BIOS entry at 0xf0000+0x94 >> Other BIOS signatures found: >> APIC: CPU 0 has ACPI ID 6 >> WARNING: Non-uniform processors. >> WARNING: Using suboptimal topology. >> ULE: setup cpu 0 >> ACPI: RSDP @ 0x0xf4f70/0x0014 (v 0 COMPAQ) >> ACPI: RSDT @ 0x0x3fffa000/0x0030 (v 1 COMPAQ P29 0x00000002 Ò >> 0x0000162E) >> ACPI: FACP @ 0x0x3fffa040/0x0074 (v 1 COMPAQ P29 0x00000002 Ò >> 0x0000162E) >> ACPI: DSDT @ 0x0x3fffa240/0x3C44 (v 1 COMPAQ DSDT 0x00000001 MSFT >> 0x0100000B) >> ACPI: FACS @ 0x0x3fffa0c0/0x0040 >> ACPI: APIC @ 0x0x3fffa100/0x00AC (v 1 COMPAQ 00000083 0x00000002 >> 0x00000000) >> ACPI: SPCR @ 0x0x3fffa1c0/0x0050 (v 1 COMPAQ SPCRRBSU 0x00000001 Ò >> 0x0000162E) >> MADT: Found IO APIC ID 2, Interrupt 0 at 0xfec00000 >> ioapic0: Routing external 8259A's -> intpin 0 >> MADT: Found IO APIC ID 3, Interrupt 16 at 0xfec01000 >> MADT: Found IO APIC ID 4, Interrupt 32 at 0xfec02000 >> MADT: Found IO APIC ID 5, Interrupt 48 at 0xfec03000 >> MADT: Interrupt override: source 0, irq 2 >> ioapic0: Routing IRQ 0 -> intpin 2 >> lapic: Routing NMI -> LINT1 >> lapic: LINT1 trigger: edge >> lapic: LINT1 polarity: high >> MADT: Forcing active-low polarity and level trigger for SCI >> ioapic0: intpin 9 polarity: low >> ioapic0: intpin 9 trigger: level >> ioapic0 <Version 1.1> irqs 0-15 on motherboard >> ioapic1 <Version 1.1> irqs 16-31 on motherboard >> ioapic2 <Version 1.1> irqs 32-47 on motherboard >> ioapic3 <Version 1.1> irqs 48-63 on motherboard >> cpu0 BSP: >> ID: 0x06000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff >> lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff >> timer: 0x000100ef therm: 0x00010000 err: 0x000100f0 pcm: 0x00000400 >> wlan: <802.11 Link Layer> >> ath_rate: version 1.2 <SampleRate bit-rate selection algorithm> >> random: <entropy source, Software, Yarrow> >> nfslock: pseudo-device >> io: <I/O> >> kbd: new array size 4 >> kbd1 at kbdmux0 >> mem: <memory> >> Pentium Pro MTRR support enabled >> null: <null device, zero device> >> ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, >> RF5413) hptrr: RocketRAID 17xx/2xxx SATA controller driver v1.2 (Aug 27 >> 2008 13:01:24) >> npx0: INT 16 interface >> acpi0: <COMPAQ P29> on motherboard >> ioapic0: routing intpin 9 (ISA IRQ 9) to vector 48 >> acpi0: [MPSAFE] >> acpi0: [ITHREAD] >> acpi0: Power Button (fixed) >> acpi0: wakeup code va 0xc3d96000 pa 0x1000 >> pci_open(1): mode 1 addr port (0x0cf8) is 0x00000000 >> pci_open(1a): mode1res=0x80000000 (0x80000000) >> pci_cfgcheck: device 0 [class=060000] [hdr=80] is there (id=00141166) >> pcibios: BIOS version 2.10 >> AcpiOsDerivePciId: \_SB_.PCI0.CFG0.MEM0 -> bus 0 dev 0 func 0 >> ACPI timer: 0/3 0/3 0/5 1/2 0/3 1/2 1/2 0/3 0/4 0/3 -> 3 >> Timecounter "ACPI-safe" frequency 3579545 Hz quality 850 >> acpi_timer0: <32-bit timer at 3.579545MHz> port 0x920-0x923 on acpi0 >> pci_link0: Index IRQ Rtd Ref IRQs >> Initial Probe 0 7 N 0 4 5 7 10 11 15 >> Validation 0 7 N 0 4 5 7 10 11 15 >> After Disable 0 255 N 0 4 5 7 10 11 15 >> pci_link1: Index IRQ Rtd Ref IRQs >> Initial Probe 0 3 N 0 4 5 7 10 11 15 >> Validation 0 255 N 0 4 5 7 10 11 15 >> After Disable 0 255 N 0 4 5 7 10 11 15 >> pci_link2: Index IRQ Rtd Ref IRQs >> Initial Probe 0 5 N 0 4 5 7 10 11 15 >> Validation 0 5 N 0 4 5 7 10 11 15 >> After Disable 0 255 N 0 4 5 7 10 11 15 >> pci_link3: Index IRQ Rtd Ref IRQs >> Initial Probe 0 11 N 0 4 5 7 10 11 15 >> Validation 0 11 N 0 4 5 7 10 11 15 >> After Disable 0 255 N 0 4 5 7 10 11 15 >> pci_link4: Index IRQ Rtd Ref IRQs >> Initial Probe 0 255 N 0 4 5 7 10 11 15 >> Validation 0 255 N 0 4 5 7 10 11 15 >> After Disable 0 255 N 0 4 5 7 10 11 15 >> pci_link5: Index IRQ Rtd Ref IRQs >> Initial Probe 0 255 N 0 4 5 7 10 11 15 >> Validation 0 255 N 0 4 5 7 10 11 15 >> After Disable 0 255 N 0 4 5 7 10 11 15 >> pci_link6: Index IRQ Rtd Ref IRQs >> Initial Probe 0 255 N 0 4 5 7 10 11 15 >> Validation 0 255 N 0 4 5 7 10 11 15 >> After Disable 0 255 N 0 4 5 7 10 11 15 >> pci_link7: Index IRQ Rtd Ref IRQs >> Initial Probe 0 255 N 0 4 5 7 10 11 15 >> Validation 0 255 N 0 4 5 7 10 11 15 >> After Disable 0 255 N 0 4 5 7 10 11 15 >> pci_link8: Index IRQ Rtd Ref IRQs >> Initial Probe 0 255 N 0 4 5 7 10 11 15 >> Validation 0 255 N 0 4 5 7 10 11 15 >> After Disable 0 255 N 0 4 5 7 10 11 15 >> pci_link9: Index IRQ Rtd Ref IRQs >> Initial Probe 0 255 N 0 4 5 7 10 11 15 >> Validation 0 255 N 0 4 5 7 10 11 15 >> After Disable 0 255 N 0 4 5 7 10 11 15 >> pci_link10: Index IRQ Rtd Ref IRQs >> Initial Probe 0 255 N 0 4 5 7 10 11 15 >> Validation 0 255 N 0 4 5 7 10 11 15 >> After Disable 0 255 N 0 4 5 7 10 11 15 >> pci_link11: Index IRQ Rtd Ref IRQs >> Initial Probe 0 15 N 0 4 5 7 10 11 15 >> Validation 0 15 N 0 4 5 7 10 11 15 >> After Disable 0 255 N 0 4 5 7 10 11 15 >> pci_link12: Index IRQ Rtd Ref IRQs >> Initial Probe 0 255 N 0 4 5 7 10 11 15 >> Validation 0 255 N 0 4 5 7 10 11 15 >> After Disable 0 255 N 0 4 5 7 10 11 15 >> pci_link13: Index IRQ Rtd Ref IRQs >> Initial Probe 0 255 N 0 4 5 7 10 11 15 >> Validation 0 255 N 0 4 5 7 10 11 15 >> After Disable 0 255 N 0 4 5 7 10 11 15 >> pci_link14: Index IRQ Rtd Ref IRQs >> Initial Probe 0 11 N 0 4 5 7 10 11 15 >> Validation 0 11 N 0 4 5 7 10 11 15 >> After Disable 0 255 N 0 4 5 7 10 11 15 >> pci_link15: Index IRQ Rtd Ref IRQs >> Initial Probe 0 10 N 0 4 5 7 10 11 15 >> Validation 0 10 N 0 4 5 7 10 11 15 >> After Disable 0 255 N 0 4 5 7 10 11 15 >> pci_link16: Index IRQ Rtd Ref IRQs >> Initial Probe 0 15 N 0 4 5 7 10 11 15 >> Validation 0 15 N 0 4 5 7 10 11 15 >> After Disable 0 255 N 0 4 5 7 10 11 15 >> pci_link17: Index IRQ Rtd Ref IRQs >> Initial Probe 0 255 N 0 4 5 7 10 11 15 >> Validation 0 255 N 0 4 5 7 10 11 15 >> After Disable 0 255 N 0 4 5 7 10 11 15 >> pci_link18: Index IRQ Rtd Ref IRQs >> Initial Probe 0 255 N 0 4 5 7 10 11 15 >> Validation 0 255 N 0 4 5 7 10 11 15 >> After Disable 0 255 N 0 4 5 7 10 11 15 >> pci_link19: Index IRQ Rtd Ref IRQs >> Initial Probe 0 255 N 0 4 5 7 10 11 15 >> Validation 0 255 N 0 4 5 7 10 11 15 >> After Disable 0 255 N 0 4 5 7 10 11 15 >> pcib0: <ACPI Host-PCI bridge> on acpi0 >> ACPI: Found matching pin for 0.15.INTA at func 2: 7 >> pci0: <ACPI PCI bus> on pcib0 >> pci0: domain=0, physical bus=0 >> found-> vendor=0x1166, dev=0x0014, revid=0x33 >> domain=0, bus=0, slot=0, func=0 >> class=06-00-00, hdrtype=0x00, mfdev=1 >> cmdreg=0x0000, statreg=0x0000, cachelnsz=16 (dwords) >> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> found-> vendor=0x1166, dev=0x0014, revid=0x00 >> domain=0, bus=0, slot=0, func=1 >> class=06-00-00, hdrtype=0x00, mfdev=1 >> cmdreg=0x0000, statreg=0x0000, cachelnsz=16 (dwords) >> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> found-> vendor=0x1166, dev=0x0014, revid=0x00 >> domain=0, bus=0, slot=0, func=2 >> class=06-00-00, hdrtype=0x00, mfdev=1 >> cmdreg=0x0000, statreg=0x0000, cachelnsz=16 (dwords) >> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> found-> vendor=0x1002, dev=0x4752, revid=0x27 >> domain=0, bus=0, slot=3, func=0 >> class=03-00-00, hdrtype=0x00, mfdev=0 >> cmdreg=0x0087, statreg=0x0290, cachelnsz=16 (dwords) >> lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns) >> powerspec 2 supports D0 D1 D2 D3 current D0 >> map[10]: type Memory, range 32, base 0xf1000000, size 24, enabled >> map[14]: type I/O Port, range 32, base 0x2400, size 8, enabled >> map[18]: type Memory, range 32, base 0xf0ff0000, size 12, enabled >> found-> vendor=0x0e11, dev=0xb203, revid=0x01 >> domain=0, bus=0, slot=4, func=0 >> class=08-80-00, hdrtype=0x00, mfdev=1 >> cmdreg=0x0103, statreg=0x0290, cachelnsz=0 (dwords) >> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> intpin=a, irq=3 >> powerspec 2 supports D0 D3 current D0 >> map[10]: type I/O Port, range 32, base 0x1800, size 8, enabled >> map[14]: type Memory, range 32, base 0xf0fe0000, size 9, enabled >> pcib0: matched entry for 0.4.INTA >> pcib0: slot 4 INTA hardwired to IRQ 16 >> found-> vendor=0x0e11, dev=0xb204, revid=0x01 >> domain=0, bus=0, slot=4, func=2 >> class=08-80-00, hdrtype=0x00, mfdev=1 >> cmdreg=0x0197, statreg=0x0290, cachelnsz=16 (dwords) >> lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> intpin=b, irq=5 >> powerspec 2 supports D0 D3 current D0 >> map[10]: type I/O Port, range 32, base 0x2800, size 8, enabled >> map[14]: type Memory, range 32, base 0xf0fd0000, size 11, enabled >> map[18]: type Memory, range 32, base 0xf0fc0000, size 13, enabled >> map[1c]: type Memory, range 32, base 0xf0f00000, size 19, enabled >> pcib0: matched entry for 0.4.INTB >> pcib0: slot 4 INTB hardwired to IRQ 17 >> found-> vendor=0x1166, dev=0x0201, revid=0x93 >> domain=0, bus=0, slot=15, func=0 >> class=06-01-00, hdrtype=0x00, mfdev=1 >> cmdreg=0x0147, statreg=0x2200, cachelnsz=0 (dwords) >> lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> found-> vendor=0x1166, dev=0x0212, revid=0x93 >> domain=0, bus=0, slot=15, func=1 >> class=01-01-8a, hdrtype=0x00, mfdev=1 >> cmdreg=0x0145, statreg=0x0200, cachelnsz=0 (dwords) >> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> map[20]: type I/O Port, range 32, base 0x2000, size 4, enabled >> found-> vendor=0x1166, dev=0x0220, revid=0x05 >> domain=0, bus=0, slot=15, func=2 >> class=0c-03-10, hdrtype=0x00, mfdev=1 >> cmdreg=0x0157, statreg=0x0280, cachelnsz=0 (dwords) >> lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x50 (20000 >> ns) intpin=a, irq=7 >> map[10]: type Memory, range 32, base 0xf0ef0000, size 12, enabled >> pcib0: matched entry for 0.15.INTA (src \_SB_.IUSB:0) >> ioapic0: Changing trigger for pin 7 to level >> ioapic0: Changing polarity for pin 7 to low >> pcib0: slot 15 INTA routed to irq 7 via \_SB_.IUSB >> found-> vendor=0x1166, dev=0x0225, revid=0x00 >> domain=0, bus=0, slot=15, func=3 >> class=06-00-00, hdrtype=0x00, mfdev=1 >> cmdreg=0x0004, statreg=0x0200, cachelnsz=0 (dwords) >> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> found-> vendor=0x1166, dev=0x0101, revid=0x05 >> domain=0, bus=0, slot=16, func=0 >> class=06-00-00, hdrtype=0x00, mfdev=1 >> cmdreg=0x0142, statreg=0x0230, cachelnsz=0 (dwords) >> lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> found-> vendor=0x1166, dev=0x0101, revid=0x05 >> domain=0, bus=0, slot=16, func=2 >> class=06-00-00, hdrtype=0x00, mfdev=1 >> cmdreg=0x0142, statreg=0x02b0, cachelnsz=0 (dwords) >> lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> found-> vendor=0x1166, dev=0x0101, revid=0x05 >> domain=0, bus=0, slot=17, func=0 >> class=06-00-00, hdrtype=0x00, mfdev=1 >> cmdreg=0x0142, statreg=0x0230, cachelnsz=0 (dwords) >> lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> found-> vendor=0x1166, dev=0x0101, revid=0x05 >> domain=0, bus=0, slot=17, func=2 >> class=06-00-00, hdrtype=0x00, mfdev=1 >> cmdreg=0x0142, statreg=0x0230, cachelnsz=0 (dwords) >> lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> vgapci0: <VGA-compatible display> port 0x2400-0x24ff mem >> 0xf1000000-0xf1ffffff,0xf0ff0000-0xf0ff0fff at device 3.0 on pci0 >> pci0: <base peripheral> at device 4.0 (no driver attached) >> pci0: <base peripheral> at device 4.2 (no driver attached) >> isab0: <PCI-ISA bridge> at device 15.0 on pci0 >> isa0: <ISA bus> on isab0 >> atapci0: <ServerWorks CSB5 UDMA100 controller> port >> 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x2000-0x200f at device 15.1 on pci0 >> atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0x2000 >> ata0: <ATA channel 0> on atapci0 >> atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0 >> atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6 >> ata0: reset tp1 mask=03 ostat0=50 ostat1=01 >> ata0: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb >> ata0: stat1=0x00 err=0x24 lsb=0xff msb=0x00 >> ata0: reset tp2 stat0=00 stat1=00 devices=0x10000 >> ioapic0: routing intpin 14 (ISA IRQ 14) to vector 49 >> ata0: [MPSAFE] >> ata0: [ITHREAD] >> ata1: <ATA channel 1> on atapci0 >> atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170 >> atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376 >> ata1: reset tp1 mask=00 ostat0=ff ostat1=ff >> ioapic0: routing intpin 15 (ISA IRQ 15) to vector 50 >> ata1: [MPSAFE] >> ata1: [ITHREAD] >> ohci0: <OHCI (generic) USB controller> mem 0xf0ef0000-0xf0ef0fff irq 7 at >> device 15.2 on pci0 >> ohci0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xf0ef0000 >> ohci0: (New OHCI DeviceId=0x02201166) >> ioapic0: routing intpin 7 (ISA IRQ 7) to vector 51 >> ohci0: [GIANT-LOCKED] >> ohci0: [ITHREAD] >> usb0: OHCI version 1.0, legacy support >> usb0: <OHCI (generic) USB controller> on ohci0 >> usb0: USB revision 1.0 >> uhub0: <(0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0 >> uhub0: 4 ports with 4 removable, self powered >> pcib1: <ACPI Host-PCI bridge> on acpi0 >> pci1: <ACPI PCI bus> on pcib1 >> pci1: domain=0, physical bus=1 >> found-> vendor=0x0e11, dev=0xb178, revid=0x01 >> domain=0, bus=1, slot=3, func=0 >> class=01-04-00, hdrtype=0x00, mfdev=0 >> cmdreg=0x0157, statreg=0x02b0, cachelnsz=16 (dwords) >> lattimer=0x47 (2130 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> intpin=a, irq=10 >> powerspec 2 supports D0 D1 D3 current D0 >> MSI supports 2 messages, 64 bit >> map[10]: type Memory, range 64, base 0xf2dc0000, size 18, enabled >> map[18]: type I/O Port, range 32, base 0x3000, size 8, enabled >> map[1c]: type Prefetchable Memory, range 64, base 0xf2cf0000, size >> 14, enabled >> pcib1: matched entry for 1.3.INTA >> pcib1: slot 3 INTA hardwired to IRQ 30 >> ciss0: <Compaq Smart Array 5i> port 0x3000-0x30ff mem >> 0xf2dc0000-0xf2dfffff,0xf2cf0000-0xf2cf3fff irq 30 at device 3.0 on pci1 >> ciss0: Reserved 0x40000 bytes for rid 0x10 type 3 at 0xf2dc0000 >> ciss0: PERFORMANT Transport >> ioapic1: routing intpin 14 (PCI IRQ 30) to vector 52 >> ciss0: [MPSAFE] >> ciss0: [ITHREAD] >> ciss0: using 256 of 1024 available commands >> ciss0: firmware 2.36 >> ciss0: 2 SCSI channels >> ciss0: signature 'CISS' >> ciss0: valence 1 >> ciss0: supported I/O methods 0xe<simple,performant,MEMQ> >> ciss0: active I/O method 0x5<performant> >> ciss0: 4G page base 0x00000000 >> ciss0: interrupt coalesce delay 0us >> ciss0: interrupt coalesce count 16 >> ciss0: max outstanding commands 1024 >> ciss0: bus types 0x2<ultra3> >> ciss0: server name '' >> ciss0: heartbeat 0x3000008e >> ciss0: 2 physical devices >> ciss0: 1 logical drive >> ciss0: logical drive (b0t0): RAID 0, 34304MB online >> pcib2: <ACPI Host-PCI bridge> on acpi0 >> pci2: <ACPI PCI bus> on pcib2 >> pci2: domain=0, physical bus=2 >> found-> vendor=0x14e4, dev=0x16a7, revid=0x02 >> domain=0, bus=2, slot=1, func=0 >> class=02-00-00, hdrtype=0x00, mfdev=0 >> cmdreg=0x0156, statreg=0x02b0, cachelnsz=16 (dwords) >> lattimer=0x40 (1920 ns), mingnt=0x40 (16000 ns), maxlat=0x00 (0 >> ns) intpin=a, irq=11 >> powerspec 2 supports D0 D3 current D0 >> MSI supports 8 messages, 64 bit >> map[10]: type Memory, range 64, base 0xf2ef0000, size 16, enabled >> pcib2: matched entry for 2.1.INTA >> pcib2: slot 1 INTA hardwired to IRQ 29 >> found-> vendor=0x14e4, dev=0x16a7, revid=0x02 >> domain=0, bus=2, slot=2, func=0 >> class=02-00-00, hdrtype=0x00, mfdev=0 >> cmdreg=0x0156, statreg=0x02b0, cachelnsz=16 (dwords) >> lattimer=0x40 (1920 ns), mingnt=0x40 (16000 ns), maxlat=0x00 (0 >> ns) intpin=a, irq=15 >> powerspec 2 supports D0 D3 current D0 >> MSI supports 8 messages, 64 bit >> map[10]: type Memory, range 64, base 0xf2ee0000, size 16, enabled >> pcib2: matched entry for 2.2.INTA >> pcib2: slot 2 INTA hardwired to IRQ 31 >> pci0:2:1:0: bad VPD cksum, remain 223 >> bge0: <Compaq NC7781 Gigabit Server Adapter, ASIC rev. 0x1002> mem >> 0xf2ef0000-0xf2efffff irq 29 at device 1.0 on pci2 >> bge0: Reserved 0x10000 bytes for rid 0x10 type 3 at 0xf2ef0000 >> miibus0: <MII bus> on bge0 >> brgphy0: <BCM5703 10/100/1000baseTX PHY> PHY 1 on miibus0 >> brgphy0: OUI 0x000818, model 0x0016, rev. 2 >> brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, >> 1000baseT-FDX, auto >> bge0: bpf attached >> bge0: Ethernet address: 00:0d:9d:93:cf:f9 >> ioapic1: routing intpin 13 (PCI IRQ 29) to vector 53 >> bge0: [MPSAFE] >> bge0: [ITHREAD] >> pci0:2:2:0: bad VPD cksum, remain 223 >> bge1: <Compaq NC7781 Gigabit Server Adapter, ASIC rev. 0x1002> mem >> 0xf2ee0000-0xf2eeffff irq 31 at device 2.0 on pci2 >> bge1: Reserved 0x10000 bytes for rid 0x10 type 3 at 0xf2ee0000 >> miibus1: <MII bus> on bge1 >> brgphy1: <BCM5703 10/100/1000baseTX PHY> PHY 1 on miibus1 >> brgphy1: OUI 0x000818, model 0x0016, rev. 2 >> brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, >> 1000baseT-FDX, auto >> bge1: bpf attached >> bge1: Ethernet address: 00:0d:9d:93:cf:f8 >> ioapic1: routing intpin 15 (PCI IRQ 31) to vector 54 >> bge1: [MPSAFE] >> bge1: [ITHREAD] >> pcib3: <ACPI Host-PCI bridge> on acpi0 >> pci3: <ACPI PCI bus> on pcib3 >> pci3: domain=0, physical bus=3 >> pcib4: <ACPI Host-PCI bridge> on acpi0 >> pci6: <ACPI PCI bus> on pcib4 >> pci6: domain=0, physical bus=6 >> found-> vendor=0x14e4, dev=0x5820, revid=0x10 >> domain=0, bus=6, slot=2, func=0 >> class=0b-40-00, hdrtype=0x00, mfdev=0 >> cmdreg=0x0156, statreg=0x02b0, cachelnsz=16 (dwords) >> lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> intpin=a, irq=15 >> powerspec 2 supports D0 D3 current D0 >> map[10]: type Memory, range 32, base 0xf7ff0000, size 16, enabled >> pcib4: matched entry for 6.2.INTA >> pcib4: slot 2 INTA hardwired to IRQ 26 >> found-> vendor=0x0e11, dev=0xa0f7, revid=0x14 >> domain=0, bus=6, slot=30, func=0 >> class=08-04-00, hdrtype=0x00, mfdev=0 >> cmdreg=0x0142, statreg=0x0430, cachelnsz=0 (dwords) >> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> intpin=a, irq=11 >> powerspec 2 supports D0 D3 current D0 >> MSI supports 1 message, 64 bit >> map[10]: type Memory, range 32, base 0xf7fe0000, size 12, enabled >> pcib4: matched entry for 6.30.INTA >> pcib4: slot 30 INTA hardwired to IRQ 18 >> pci6: <processor> at device 2.0 (no driver attached) >> pci6: <base peripheral, PCI hot-plug controller> at device 30.0 (no >> driver attached) >> acpi_tz0: <Thermal Zone> on acpi0 >> atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 >> atkbd0: <AT Keyboard> irq 1 on atkbdc0 >> atkbd: the current kbd controller command byte 0065 >> atkbd: keyboard ID 0x41ab (2) >> kbdc: RESET_KBD return code:00fa >> kbdc: RESET_KBD status:00aa >> kbd0 at atkbd0 >> kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000 >> ioapic0: routing intpin 1 (ISA IRQ 1) to vector 55 >> atkbd0: [GIANT-LOCKED] >> atkbd0: [ITHREAD] >> psm0: unable to allocate IRQ >> psmcpnp0: <PS/2 mouse port> irq 12 on acpi0 >> psm0: current command byte:0065 >> kbdc: TEST_AUX_PORT status:0000 >> kbdc: RESET_AUX return code:00fa >> kbdc: RESET_AUX status:ffffffff >> kbdc: DIAGNOSE status:0055 >> kbdc: TEST_KBD_PORT status:0000 >> psm0: failed to reset the aux device. >> fdc0: <floppy drive controller (FDE)> port 0x3f2-0x3f5 irq 6 drq 2 on >> acpi0 fdc0: ic_type 90 part_id 73 >> ioapic0: routing intpin 6 (ISA IRQ 6) to vector 56 >> fdc0: [FILTER] >> fd0: <1440-KB 3.5" drive> on fdc0 drive 0 >> cpu0: <ACPI CPU> on acpi0 >> cpu0: switching to generic Cx mode >> p4tcc0: <CPU Frequency Thermal Control> on cpu0 >> unknown: status reg test failed ff >> unknown: status reg test failed ff >> unknown: status reg test failed ff >> unknown: status reg test failed ff >> ahc_isa_probe 0: ioport 0xc00 alloc failed >> ex_isa_identify() >> ata: ata0 already exists; skipping it >> ata: ata1 already exists; skipping it >> atkbdc: atkbdc0 already exists; skipping it >> fdc: fdc0 already exists; skipping it >> pnp_identify: Trying Read_Port at 203 >> pnp_identify: Trying Read_Port at 243 >> pnp_identify: Trying Read_Port at 283 >> pnp_identify: Trying Read_Port at 2c3 >> pnp_identify: Trying Read_Port at 303 >> pnp_identify: Trying Read_Port at 343 >> pnp_identify: Trying Read_Port at 383 >> pnp_identify: Trying Read_Port at 3c3 >> PNP Identify complete >> sc: sc0 already exists; skipping it >> vga: vga0 already exists; skipping it >> isa_probe_children: disabling PnP devices >> isa_probe_children: probing non-PnP devices >> pmtimer0 on isa0 >> orm0: <ISA Option ROMs> at iomem >> 0xc0000-0xc7fff,0xc8000-0xcbfff,0xcc000-0xcd7ff,0xee000-0xeffff pnpid >> ORM0000 on isa0 >> adv0: not probed (disabled) >> aha0: not probed (disabled) >> aic0: not probed (disabled) >> atrtc0: <AT Real Time Clock> at port 0x70 irq 8 on isa0 >> atrtc0: registered as a time-of-day clock (resolution 1000000us) >> bt0: not probed (disabled) >> cs0: not probed (disabled) >> ed0: not probed (disabled) >> fe0: not probed (disabled) >> ie0: not probed (disabled) >> le0: not probed (disabled) >> ppc0: parallel port not found. >> ppc0: <Parallel port> failed to probe at irq 7 on isa0 >> sc0: <System console> at flags 0x100 on isa0 >> sc0: VGA <16 virtual consoles, flags=0x300> >> sc0: fb0, kbd1, terminal emulator: sc (syscons terminal) >> sio0 failed to probe at port 0x3f8 irq 4 on isa0 >> sn0: not probed (disabled) >> uart0: <16550 or compatible> at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 >> ioapic0: routing intpin 4 (ISA IRQ 4) to vector 57 >> uart0: [FILTER] >> uart0: fast interrupt >> uart0: console (115200,n,8,1) >> uart1: <ns8250> failed to probe at port 0x2f8-0x2ff irq 3 on isa0 >> uart2: not probed (disabled) >> uart3: not probed (disabled) >> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 >> isa_probe_children: probing PnP devices >> Device configuration finished. >> procfs registered >> lapic: Divisor 2, Frequency 66365047 hz >> Timecounter "TSC" frequency 3185522100 Hz quality 800 >> Timecounters tick every 1.000 msec >> lo0: bpf attached >> hptrr: no controller detected. >> ata0: identify ch->devices=00010000 >> fdc0: output ready timeout >> fdc0: output ready timeout >> fdc0: output ready timeout >> fdc0: output ready timeout >> fdc0: output ready timeout >> fdc0: output ready timeout >> fdc0: output ready timeout >> ata0-master: pio=PIO4 wdma=UNSUPPORTED udma=UNSUPPORTED cable=40 wire >> acd0: setting PIO4 on CSB5 chip >> acd0: <COMPAQ CD-ROM SN-124/N104> CDROM drive at ata0 as master >> acd0: read 4134KB/s (4134KB/s), 128KB buffer, PIO4 >> acd0: Reads: CDR, CDRW, CDDA stream, packet >> acd0: Writes: >> acd0: Audio: play, 255 volume levels >> acd0: Mechanism: ejectable tray, unlocked >> acd0: Medium: no/blank disc >> ata1: identify ch->devices=00000000 >> fdc0: output ready timeout >> fdc0: input ready timeout >> fdc0: input ready timeout >> fdc0: output ready timeout >> fdc0: input ready timeout >> fdc0: input ready timeout >> fdc0: output ready timeout >> fdc0: input ready timeout >> fdc0: input ready timeout >> fdc0: output ready timeout >> fdc0: input ready timeout >> fdc0: input ready timeout >> run_interrupt_driven_hooks: still waiting after 60 seconds for xpt_config >> run_interrupt_driven_hooks: still waiting after 120 seconds for >> xpt_config run_interrupt_driven_hooks: still waiting after 180 seconds >> for xpt_config run_interrupt_driven_hooks: still waiting after 240 >> seconds for xpt_config run_interrupt_driven_hooks: still waiting after >> 300 seconds for xpt_config panic: run_interrupt_driven_config_hooks: >> waited too long cpuid = 0 >> KDB: enter: panic >> [thread pid 0 tid 100000 ] >> Stopped at kdb_enter+0x3a: movl $0,kdb_why >> db> >> >> for comparison here is -current from June 11 2008 that boots. I tried >> the July 2008's snapshot and it fails in a similar way to today's >> -current: >> >> OK set hint.sio.0.at="isa" >> OK set hint.sio.0.port="0x3F8" >> OK set hint.sio.0.flags="0x10" >> OK set hint.sio.0.irq="4" >> OK unload kernel >> OK load /boot/kernel.old/kernel >> /boot/kernel.old/kernel text=0x77e034 data=0xba7e0+0xacf78 >> syms=[0x4+0x81940+0x4+0xacbd8] >> OK boot -v -s >> /boot/kernel/acpi.ko text=0x5512c data=0x2640+0x182c >> syms=[0x4+0x8b80+0x4+0xbe19] >> loading required module 'kernel' >> elf32_loadfile: kernel already loaded >> ACPI autoload failed - no such file or directory >> GDB: no debug ports present >> KDB: debugger backends: ddb >> KDB: current backend: ddb >> SMAP type=01 base=0000000000000000 len=000000000009f400 >> SMAP type=02 base=000000000009f400 len=0000000000000c00 >> SMAP type=02 base=00000000000f0000 len=0000000000010000 >> SMAP type=01 base=0000000000100000 len=000000003fefa000 >> SMAP type=03 base=000000003fffa000 len=0000000000006000 >> SMAP type=02 base=00000000fec00000 len=0000000000010000 >> SMAP type=02 base=00000000fee00000 len=0000000000010000 >> SMAP type=02 base=00000000ffc00000 len=0000000000400000 >> SMAP type=01 base=0000000100000000 len=0000000000000000 >> Copyright (c) 1992-2008 The FreeBSD Project. >> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 >> The Regents of the University of California. All rights reserved. >> FreeBSD is a registered trademark of The FreeBSD Foundation. >> FreeBSD 8.0-CURRENT #6: Wed Jun 11 20:14:47 PDT 2008 >> root@dl380-1.f5test.net:/usr/obj/usr/src/sys/DL380 >> WARNING: WITNESS option enabled, expect reduced performance. >> Preloaded elf kernel "/boot/kernel.old/kernel" at 0xc0e16000. >> Timecounter "i8254" frequency 1193182 Hz quality 0 >> Calibrating TSC clock ... TSC clock: 3185638132 Hz >> CPU: Intel(R) Xeon(TM) CPU 3.20GHz (3185.64-MHz 686-class CPU) >> Origin = "GenuineIntel" Id = 0xf25 Stepping = 5 >> >> Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> >> Features2=0x4400<CNXT-ID,xTPR> >> Logical CPUs per core: 2 >> >> Instruction TLB: 4 KB, 2 MB or 4 MB pages, fully associative, 64 entries >> Data TLB: 4 KB or 4 MB pages, fully associative, 64 entries >> 1st-level data cache: 8 KB, 4-way set associative, sectored cache, 64 >> byte line size >> 3rd-level cache: 1 MB, 8-way set associative, sectored cache, 64 byte >> line size >> Trace cache: 12K-uops, 8-way set associative >> 2nd-level cache: 512 KB, 8-way set associative, sectored cache, 64 byte >> line size >> real memory = 1073717248 (1023 MB) >> Physical memory chunk(s): >> 0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages) >> 0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages) >> 0x0000000001025000 - 0x000000003eeaefff, 1038655488 bytes (253578 pages) >> avail memory = 1038147584 (990 MB) >> MP Configuration Table version 1.4 found at 0xc00f29ca >> APIC: Using the MPTable enumerator. >> SMP: Added CPU 6 (BSP) >> MPTable: <COMPAQ PROLIANT > >> bios32: Found BIOS32 Service Directory header at 0xc00ffee0 >> bios32: Entry = 0xf0000 (c00f0000) Rev = 0 Len = 1 >> pcibios: PCI BIOS entry at 0xf0000+0x94 >> Other BIOS signatures found: >> WARNING: Non-uniform processors. >> WARNING: Using suboptimal topology. >> ULE: setup cpu 0 >> ioapic0: Assuming intbase of 0 >> ioapic0: Routing external 8259A's -> intpin 0 >> ioapic1: Assuming intbase of 16 >> ioapic2: Assuming intbase of 32 >> ioapic3: Assuming intbase of 48 >> ioapic0: intpin 7 bus PCI >> ioapic0: intpin 7 trigger: level >> ioapic0: intpin 7 polarity: low >> ioapic0: Routing IRQ 0 -> intpin 2 >> ioapic0: intpin 9 trigger: level >> ioapic0: intpin 9 polarity: low >> lapic: Routing ExtINT -> LINT0 >> lapic: LINT0 trigger: edge >> lapic: LINT0 polarity: high >> lapic: Routing NMI -> LINT1 >> lapic: LINT1 trigger: edge >> lapic: LINT1 polarity: high >> ioapic0 <Version 1.1> irqs 0-15 on motherboard >> ioapic1 <Version 1.1> irqs 16-31 on motherboard >> ioapic2 <Version 1.1> irqs 32-47 on motherboard >> ioapic3 <Version 1.1> irqs 48-63 on motherboard >> cpu0 BSP: >> ID: 0x06000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff >> lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff >> timer: 0x000100ef therm: 0x00010000 err: 0x000100f0 pcm: 0x00010000 >> ath_rate: version 1.2 <SampleRate bit-rate selection algorithm> >> wlan: <802.11 Link Layer> >> null: <null device, zero device> >> random: <entropy source, Software, Yarrow> >> nfslock: pseudo-device >> kbd: new array size 4 >> kbd1 at kbdmux0 >> mem: <memory> >> Pentium Pro MTRR support enabled >> io: <I/O> >> ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, >> RF5413) hptrr: RocketRAID 17xx/2xxx SATA controller driver v1.2 (Jun 11 >> 2008 20:11:11) >> npx0: INT 16 interface >> pci_open(1): mode 1 addr port (0x0cf8) is 0x00000000 >> pci_open(1a): mode1res=0x80000000 (0x80000000) >> pci_cfgcheck: device 0 [class=060000] [hdr=80] is there (id=00141166) >> pcibios: BIOS version 2.10 >> pcib0: <MPTable Host-PCI bridge> pcibus 0 on motherboard >> pci0: <PCI bus> on pcib0 >> pci0: domain=0, physical bus=0 >> found-> vendor=0x1166, dev=0x0014, revid=0x33 >> domain=0, bus=0, slot=0, func=0 >> class=06-00-00, hdrtype=0x00, mfdev=1 >> cmdreg=0x0000, statreg=0x0000, cachelnsz=16 (dwords) >> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> found-> vendor=0x1166, dev=0x0014, revid=0x00 >> domain=0, bus=0, slot=0, func=1 >> class=06-00-00, hdrtype=0x00, mfdev=1 >> cmdreg=0x0000, statreg=0x0000, cachelnsz=16 (dwords) >> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> found-> vendor=0x1166, dev=0x0014, revid=0x00 >> domain=0, bus=0, slot=0, func=2 >> class=06-00-00, hdrtype=0x00, mfdev=1 >> cmdreg=0x0000, statreg=0x0000, cachelnsz=16 (dwords) >> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> found-> vendor=0x1002, dev=0x4752, revid=0x27 >> domain=0, bus=0, slot=3, func=0 >> class=03-00-00, hdrtype=0x00, mfdev=0 >> cmdreg=0x0087, statreg=0x0290, cachelnsz=16 (dwords) >> lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns) >> powerspec 2 supports D0 D1 D2 D3 current D0 >> map[10]: type Memory, range 32, base 0xf1000000, size 24, enabled >> map[14]: type I/O Port, range 32, base 0x2400, size 8, enabled >> map[18]: type Memory, range 32, base 0xf0ff0000, size 12, enabled >> found-> vendor=0x0e11, dev=0xb203, revid=0x01 >> domain=0, bus=0, slot=4, func=0 >> class=08-80-00, hdrtype=0x00, mfdev=1 >> cmdreg=0x0103, statreg=0x0290, cachelnsz=0 (dwords) >> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> intpin=a, irq=3 >> powerspec 2 supports D0 D3 current D0 >> map[10]: type I/O Port, range 32, base 0x1800, size 8, enabled >> map[14]: type Memory, range 32, base 0xf0fe0000, size 9, enabled >> pcib0: slot 4 INTA routed to irq 16 >> found-> vendor=0x0e11, dev=0xb204, revid=0x01 >> domain=0, bus=0, slot=4, func=2 >> class=08-80-00, hdrtype=0x00, mfdev=1 >> cmdreg=0x0197, statreg=0x0290, cachelnsz=16 (dwords) >> lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> intpin=b, irq=5 >> powerspec 2 supports D0 D3 current D0 >> map[10]: type I/O Port, range 32, base 0x2800, size 8, enabled >> map[14]: type Memory, range 32, base 0xf0fd0000, size 11, enabled >> map[18]: type Memory, range 32, base 0xf0fc0000, size 13, enabled >> map[1c]: type Memory, range 32, base 0xf0f00000, size 19, enabled >> pcib0: slot 4 INTB routed to irq 17 >> found-> vendor=0x1166, dev=0x0201, revid=0x93 >> domain=0, bus=0, slot=15, func=0 >> class=06-01-00, hdrtype=0x00, mfdev=1 >> cmdreg=0x0147, statreg=0x2200, cachelnsz=0 (dwords) >> lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> found-> vendor=0x1166, dev=0x0212, revid=0x93 >> domain=0, bus=0, slot=15, func=1 >> class=01-01-8a, hdrtype=0x00, mfdev=1 >> cmdreg=0x0145, statreg=0x0200, cachelnsz=0 (dwords) >> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> map[20]: type I/O Port, range 32, base 0x2000, size 4, enabled >> found-> vendor=0x1166, dev=0x0220, revid=0x05 >> domain=0, bus=0, slot=15, func=2 >> class=0c-03-10, hdrtype=0x00, mfdev=1 >> cmdreg=0x0157, statreg=0x0280, cachelnsz=0 (dwords) >> lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x50 (20000 >> ns) intpin=a, irq=7 >> map[10]: type Memory, range 32, base 0xf0ef0000, size 12, enabled >> pcib0: slot 15 INTA routed to irq 7 >> found-> vendor=0x1166, dev=0x0225, revid=0x00 >> domain=0, bus=0, slot=15, func=3 >> class=06-00-00, hdrtype=0x00, mfdev=1 >> cmdreg=0x0004, statreg=0x0200, cachelnsz=0 (dwords) >> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> found-> vendor=0x1166, dev=0x0101, revid=0x05 >> domain=0, bus=0, slot=16, func=0 >> class=06-00-00, hdrtype=0x00, mfdev=1 >> cmdreg=0x0142, statreg=0x2230, cachelnsz=0 (dwords) >> lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> found-> vendor=0x1166, dev=0x0101, revid=0x05 >> domain=0, bus=0, slot=16, func=2 >> class=06-00-00, hdrtype=0x00, mfdev=1 >> cmdreg=0x0142, statreg=0x02b0, cachelnsz=0 (dwords) >> lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> found-> vendor=0x1166, dev=0x0101, revid=0x05 >> domain=0, bus=0, slot=17, func=0 >> class=06-00-00, hdrtype=0x00, mfdev=1 >> cmdreg=0x0142, statreg=0x2230, cachelnsz=0 (dwords) >> lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> found-> vendor=0x1166, dev=0x0101, revid=0x05 >> domain=0, bus=0, slot=17, func=2 >> class=06-00-00, hdrtype=0x00, mfdev=1 >> cmdreg=0x0142, statreg=0x0230, cachelnsz=0 (dwords) >> lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> vgapci0: <VGA-compatible display> port 0x2400-0x24ff mem >> 0xf1000000-0xf1ffffff,0xf0ff0000-0xf0ff0fff at device 3.0 on pci0 >> pci0: <base peripheral> at device 4.0 (no driver attached) >> pci0: <base peripheral> at device 4.2 (no driver attached) >> isab0: <PCI-ISA bridge> at device 15.0 on pci0 >> isa0: <ISA bus> on isab0 >> atapci0: <ServerWorks CSB5 UDMA100 controller> port >> 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x2000-0x200f at device 15.1 on pci0 >> atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0x2000 >> ata0: <ATA channel 0> on atapci0 >> atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0 >> atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6 >> ata0: reset tp1 mask=03 ostat0=50 ostat1=01 >> ata0: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb >> ata0: stat1=0x00 err=0x24 lsb=0xff msb=0x00 >> ata0: reset tp2 stat0=00 stat1=00 devices=0x10000 >> ioapic0: routing intpin 14 (ISA IRQ 14) to vector 48 >> ata0: [MPSAFE] >> ata0: [ITHREAD] >> ata1: <ATA channel 1> on atapci0 >> atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170 >> atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376 >> ata1: reset tp1 mask=00 ostat0=ff ostat1=ff >> ioapic0: routing intpin 15 (ISA IRQ 15) to vector 49 >> ata1: [MPSAFE] >> ata1: [ITHREAD] >> ohci0: <OHCI (generic) USB controller> mem 0xf0ef0000-0xf0ef0fff irq 7 at >> device 15.2 on pci0 >> ohci0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xf0ef0000 >> ohci0: (New OHCI DeviceId=0x02201166) >> ioapic0: routing intpin 7 (PCI IRQ 7) to vector 50 >> ohci0: [GIANT-LOCKED] >> ohci0: [ITHREAD] >> usb0: OHCI version 1.0, legacy support >> usb0: SMM does not respond, resetting >> usb0: <OHCI (generic) USB controller> on ohci0 >> usb0: USB revision 1.0 >> uhub0: <(0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0 >> uhub0: 4 ports with 4 removable, self powered >> pcib1: <MPTable Host-PCI bridge> pcibus 1 on motherboard >> pci1: <PCI bus> on pcib1 >> pci1: domain=0, physical bus=1 >> found-> vendor=0x0e11, dev=0xb178, revid=0x01 >> domain=0, bus=1, slot=3, func=0 >> class=01-04-00, hdrtype=0x00, mfdev=0 >> cmdreg=0x0157, statreg=0x02b0, cachelnsz=16 (dwords) >> lattimer=0x47 (2130 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> intpin=a, irq=10 >> powerspec 2 supports D0 D1 D3 current D0 >> MSI supports 2 messages, 64 bit >> map[10]: type Memory, range 64, base 0xf2dc0000, size 18, enabled >> map[18]: type I/O Port, range 32, base 0x3000, size 8, enabled >> map[1c]: type Prefetchable Memory, range 64, base 0xf2cf0000, size >> 14, enabled >> pcib1: slot 3 INTA routed to irq 30 >> ciss0: <Compaq Smart Array 5i> port 0x3000-0x30ff mem >> 0xf2dc0000-0xf2dfffff,0xf2cf0000-0xf2cf3fff irq 30 at device 3.0 on pci1 >> ciss0: Reserved 0x40000 bytes for rid 0x10 type 3 at 0xf2dc0000 >> ioapic1: routing intpin 14 (PCI IRQ 30) to vector 51 >> ciss0: [MPSAFE] >> ciss0: [ITHREAD] >> ciss0: using 256 of 1024 available commands >> ciss0: firmware 2.36 >> ciss0: 2 SCSI channels >> ciss0: signature 'CISS' >> ciss0: valence 1 >> ciss0: supported I/O methods 0xe<simple,performant,MEMQ> >> ciss0: active I/O method 0x3<simple> >> ciss0: 4G page base 0x00000000 >> ciss0: interrupt coalesce delay 1000us >> ciss0: interrupt coalesce count 16 >> ciss0: max outstanding commands 1024 >> ciss0: bus types 0x2<ultra3> >> ciss0: server name '' >> ciss0: heartbeat 0x3000006e >> ciss0: 2 physical devices >> ciss0: 1 logical drive >> ciss0: logical drive (b0t0): RAID 0, 34304MB online >> pcib3: <MPTable Host-PCI bridge> pcibus 3 on motherboard >> pci3: <PCI bus> on pcib3 >> pci3: domain=0, physical bus=3 >> pcib6: <MPTable Host-PCI bridge> pcibus 6 on motherboard >> pci6: <PCI bus> on pcib6 >> pci6: domain=0, physical bus=6 >> found-> vendor=0x14e4, dev=0x5820, revid=0x10 >> domain=0, bus=6, slot=2, func=0 >> class=0b-40-00, hdrtype=0x00, mfdev=0 >> cmdreg=0x0156, statreg=0x02b0, cachelnsz=16 (dwords) >> lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> intpin=a, irq=15 >> powerspec 2 supports D0 D3 current D0 >> map[10]: type Memory, range 32, base 0xf7ff0000, size 16, enabled >> pcib6: slot 2 INTA routed to irq 26 >> found-> vendor=0x0e11, dev=0xa0f7, revid=0x14 >> domain=0, bus=6, slot=30, func=0 >> class=08-04-00, hdrtype=0x00, mfdev=0 >> cmdreg=0x0142, statreg=0x0430, cachelnsz=0 (dwords) >> lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) >> intpin=a, irq=11 >> powerspec 2 supports D0 D3 current D0 >> MSI supports 1 message, 64 bit >> map[10]: type Memory, range 32, base 0xf7fe0000, size 12, enabled >> pcib6: slot 30 INTA routed to irq 18 >> pci6: <processor> at device 2.0 (no driver attached) >> pci6: <base peripheral, PCI hot-plug controller> at device 30.0 (no >> driver attached) >> pcib2: <MPTable Host-PCI bridge> pcibus 2 on motherboard >> pci2: <PCI bus> on pcib2 >> pci2: domain=0, physical bus=2 >> found-> vendor=0x14e4, dev=0x16a7, revid=0x02 >> domain=0, bus=2, slot=1, func=0 >> class=02-00-00, hdrtype=0x00, mfdev=0 >> cmdreg=0x0156, statreg=0x02b0, cachelnsz=16 (dwords) >> lattimer=0x40 (1920 ns), mingnt=0x40 (16000 ns), maxlat=0x00 (0 >> ns) intpin=a, irq=11 >> powerspec 2 supports D0 D3 current D0 >> MSI supports 8 messages, 64 bit >> map[10]: type Memory, range 64, base 0xf2ef0000, size 16, enabled >> pcib2: slot 1 INTA routed to irq 29 >> found-> vendor=0x14e4, dev=0x16a7, revid=0x02 >> domain=0, bus=2, slot=2, func=0 >> class=02-00-00, hdrtype=0x00, mfdev=0 >> cmdreg=0x0156, statreg=0x02b0, cachelnsz=16 (dwords) >> lattimer=0x40 (1920 ns), mingnt=0x40 (16000 ns), maxlat=0x00 (0 >> ns) intpin=a, irq=15 >> powerspec 2 supports D0 D3 current D0 >> MSI supports 8 messages, 64 bit >> map[10]: type Memory, range 64, base 0xf2ee0000, size 16, enabled >> pcib2: slot 2 INTA routed to irq 31 >> pci0:2:1:0: bad VPD cksum, remain 223 >> bge0: <Compaq NC7781 Gigabit Server Adapter, ASIC rev. 0x1002> mem >> 0xf2ef0000-0xf2efffff irq 29 at device 1.0 on pci2 >> bge0: Reserved 0x10000 bytes for rid 0x10 type 3 at 0xf2ef0000 >> miibus0: <MII bus> on bge0 >> brgphy0: <BCM5703 10/100/1000baseTX PHY> PHY 1 on miibus0 >> brgphy0: OUI 0x000818, model 0x0016, rev. 2 >> brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, >> 1000baseT-FDX, auto >> bge0: bpf attached >> bge0: Ethernet address: 00:0d:9d:93:cf:f9 >> ioapic1: routing intpin 13 (PCI IRQ 29) to vector 52 >> bge0: [MPSAFE] >> bge0: [ITHREAD] >> pci0:2:2:0: bad VPD cksum, remain 223 >> bge1: <Compaq NC7781 Gigabit Server Adapter, ASIC rev. 0x1002> mem >> 0xf2ee0000-0xf2eeffff irq 31 at device 2.0 on pci2 >> bge1: Reserved 0x10000 bytes for rid 0x10 type 3 at 0xf2ee0000 >> miibus1: <MII bus> on bge1 >> brgphy1: <BCM5703 10/100/1000baseTX PHY> PHY 1 on miibus1 >> brgphy1: OUI 0x000818, model 0x0016, rev. 2 >> brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, >> 1000baseT-FDX, auto >> bge1: bpf attached >> bge1: Ethernet address: 00:0d:9d:93:cf:f8 >> ioapic1: routing intpin 15 (PCI IRQ 31) to vector 53 >> bge1: [MPSAFE] >> bge1: [ITHREAD] >> cpu0 on motherboard >> p4tcc0: <CPU Frequency Thermal Control> on cpu0 >> eisa0: <EISA bus> on motherboard >> mainboard0: <CPQ0727 (System Board)> at slot 0 on eisa0 >> unknown: status reg test failed ff >> unknown: status reg test failed ff >> unknown: status reg test failed 0 >> unknown: status reg test failed ff >> unknown: status reg test failed ff >> unknown: status reg test failed ff >> ex_isa_identify() >> ata: ata0 already exists; skipping it >> ata: ata1 already exists; skipping it >> pnp_identify: Trying Read_Port at 203 >> pnp_identify: Trying Read_Port at 243 >> pnp_identify: Trying Read_Port at 283 >> pnp_identify: Trying Read_Port at 2c3 >> pnp_identify: Trying Read_Port at 303 >> pnp_identify: Trying Read_Port at 343 >> pnp_identify: Trying Read_Port at 383 >> pnp_identify: Trying Read_Port at 3c3 >> PNP Identify complete >> sc: sc0 already exists; skipping it >> vga: vga0 already exists; skipping it >> isa_probe_children: disabling PnP devices >> isa_probe_children: probing non-PnP devices >> pmtimer0 on isa0 >> orm0: <ISA Option ROMs> at iomem >> 0xc0000-0xc7fff,0xc8000-0xcbfff,0xcc000-0xcd7ff,0xee000-0xeffff pnpid >> ORM0000 on isa0 >> adv0: not probed (disabled) >> aha0: not probed (disabled) >> aic0: not probed (disabled) >> atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 >> atkbd0: <AT Keyboard> irq 1 on atkbdc0 >> atkbd: the current kbd controller command byte 0065 >> atkbd: keyboard ID 0x41ab (2) >> kbdc: RESET_KBD return code:00fa >> kbdc: RESET_KBD status:00aa >> kbd0 at atkbd0 >> kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000 >> ioapic0: routing intpin 1 (ISA IRQ 1) to vector 54 >> atkbd0: [GIANT-LOCKED] >> atkbd0: [ITHREAD] >> psm0: current command byte:0065 >> kbdc: TEST_AUX_PORT status:0000 >> kbdc: RESET_AUX return code:00fa >> kbdc: RESET_AUX status:ffffffff >> kbdc: DIAGNOSE status:0055 >> kbdc: TEST_KBD_PORT status:0000 >> psm0: failed to reset the aux device. >> atrtc0: <AT Real Time Clock> at port 0x70 irq 8 on isa0 >> atrtc0: registered as a time-of-day clock (resolution 1000000us) >> bt0: not probed (disabled) >> cs0: not probed (disabled) >> ed0: not probed (disabled) >> fdc0: ic_type 90 part_id 73 >> fdc0: <Enhanced floppy controller> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 >> on isa0 >> fdc0: ic_type 90 part_id 73 >> ioapic0: routing intpin 6 (ISA IRQ 6) to vector 55 >> fdc0: [FILTER] >> fd0: <1440-KB 3.5" drive> on fdc0 drive 0 >> fe0: not probed (disabled) >> ie0: not probed (disabled) >> le0: not probed (disabled) >> ppc0: parallel port not found. >> ppc0: <Parallel port> failed to probe at irq 7 on isa0 >> sc0: <System console> at flags 0x100 on isa0 >> sc0: VGA <16 virtual consoles, flags=0x300> >> sc0: fb0, kbd1, terminal emulator: sc (syscons terminal) >> sio0: irq maps: 0x1 0x11 0x1 0x1 >> sio0: irq maps: 0x1 0x11 0x1 0x1 >> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 >> sio0: type 16550A, console >> ioapic0: routing intpin 4 (ISA IRQ 4) to vector 56 >> sio0: [FILTER] >> sn0: not probed (disabled) >> uart0: <ns8250> failed to probe at port 0x3f8 irq 4 on isa0 >> uart1: <ns8250> failed to probe at port 0x2f8-0x2ff irq 3 on isa0 >> uart2: not probed (disabled) >> uart3: not probed (disabled) >> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 >> isa_probe_children: probing PnP devices >> Device configuration finished. >> procfs registered >> lapic: Divisor 2, Frequency 66367465 hz >> Timecounter "TSC" frequency 3185638132 Hz quality 800 >> Timecounters tick every 1.000 msec >> lo0: bpf attached >> hptrr: no controller detected. >> ata0: identify ch->devices=00010000 >> ata0-master: pio=PIO4 wdma=UNSUPPORTED udma=UNSUPPORTED cable=40 wire >> acd0: setting PIO4 on CSB5 chip >> acd0: <COMPAQ CD-ROM SN-124/N104> CDROM drive at ata0 as master >> acd0: read 4134KB/s (4134KB/s), 128KB buffer, PIO4 >> acd0: Reads: CDR, CDRW, CDDA stream, packet >> acd0: Writes: >> acd0: Audio: play, 255 volume levels >> acd0: Mechanism: ejectable tray, unlocked >> acd0: Medium: no/blank disc >> ata1: identify ch->devices=00000000 >> da0 at ciss0 bus 0 target 0 lun 0 >> da0: <COMPAQ RAID 0 VOLUME OK> Fixed Direct Access SCSI-0 device >> da0: 135.168MB/s transfers >> da0: 34727MB (71122560 512 byte sectors: 255H 32S/T 8716C) >> GEOM: new disk da0 >> pass0 at ciss0 bus 0 target 0 lun 0 >> pass0: <COMPAQ RAID 0 VOLUME OK> Fixed Direct Access SCSI-0 device >> pass0: 135.168MB/s transfers >> ATA PseudoRAID loaded >> WARNING: WITNESS option enabled, expect reduced performance. >> lock order reversal: (sleepable after non-sleepable) >> 1st 0xc43d601c struct mount mtx (struct mount mtx) >> @ /usr/src/sys/kern/vfs_subr.c:343 >> 2nd 0xc43d6000 vfslock (vfslock) @ /usr/src/sys/kern/vfs_subr.c:370 >> KDB: stack backtrace: >> db_trace_self_wrapper(c0b46739,c3d9cb68,c07cf01e,c0b48fa6,c43d6000,...) >> at db_trace_self_wrapper+0x26 >> kdb_backtrace(c0b48fa6,c43d6000,c0b4ed2d,c0b4ed2d,c0b4f2d2,...) at >> kdb_backtrace+0x29 >> witness_checkorder(c43d6000,1,c0b4f2d2,172,4,...) at >> witness_checkorder+0x6ee >> __lockmgr_args(c43d6000,200100,c43d601c,0,0,...) at __lockmgr_args+0x221 >> vfs_busy(c43d6000,200,0,c409ed20,1,...) at vfs_busy+0x1d4 >> vfs_mount_alloc(0,c0bf9bc0,c0b4f078,c409ed20,c080cf40,...) at >> vfs_mount_alloc+0x78 >> vfs_mountroot(c0c6a5d0,4,c0b3e263,264,0,...) at vfs_mountroot+0x26f >> start_init(0,c3d9cd38,c0b3fbac,324,c409cd0c,...) at start_init+0x65 >> fork_exit(c0756550,0,c3d9cd38) at fork_exit+0xc5 >> fork_trampoline() at fork_trampoline+0x8 >> --- trap 0, eip = 0, esp = 0xc3d9cd70, ebp = 0 --- >> lock order reversal: (sleepable after non-sleepable) >> 1st 0xc4225e10 vnode interlock (vnode interlock) >> @ /usr/src/sys/fs/devfs/devfs_vnops.c:288 >> 2nd 0xc4225df4 devfs (devfs) @ /usr/src/sys/kern/vfs_subr.c:2044 >> KDB: stack backtrace: >> db_trace_self_wrapper(c0b46739,c3d9ca90,c07cf01e,c0b48fa6,c4225df4,...) >> at db_trace_self_wrapper+0x26 >> kdb_backtrace(c0b48fa6,c4225df4,c0b39bed,c0b39bed,c0b4f2d2,...) at >> kdb_backtrace+0x29 >> witness_checkorder(c4225df4,9,c0b4f2d2,7fc,c4225df4,...) at >> witness_checkorder+0x6ee >> __lockmgr_args(c4225df4,80100,c4225e10,0,0,...) at __lockmgr_args+0x7a8 >> vop_stdlock(c3d9cb8c,c0b39da3,c0b3cf7a,80100,c4225d9c,...) at >> vop_stdlock+0x62 >> VOP_LOCK1_APV(c0bf9ca0,c3d9cb8c,c0c39140,c4225d9c,80100,...) at >> VOP_LOCK1_APV+0xa5 >> _vn_lock(c4225d9c,80100,c0b4f2d2,7fc,c0b39da3,...) at _vn_lock+0x5e >> vget(c4225d9c,80100,c409ed20,121,c0b39d40,...) at vget+0xac >> devfs_allocv(c41da580,c43d6000,c3d9cc20,c409ed20,c409edc4,...) at >> devfs_allocv+0x118 >> devfs_root(c43d6000,80000,c0cbf234,c409ed20,4,...) at devfs_root+0x51 >> set_rootvnode(c0cbf220,0,c0b4ec2f,5f1,c080cf40,...) at set_rootvnode+0x2d >> vfs_mountroot(c0c6a5d0,4,c0b3e263,264,0,...) at vfs_mountroot+0x34d >> start_init(0,c3d9cd38,c0b3fbac,324,c409cd0c,...) at start_init+0x65 >> fork_exit(c0756550,0,c3d9cd38) at fork_exit+0xc5 >> fork_trampoline() at fork_trampoline+0x8 >> --- trap 0, eip = 0, esp = 0xc3d9cd70, ebp = 0 --- >> Trying to mount root from ufs:/dev/da0s1a >> ct_to_ts([2008-08-27 14:46:04]) = 1219848364.000000000 >> lock order reversal: (sleepable after non-sleepable) >> 1st 0xc4225b20 bufobj interlock (bufobj interlock) >> @ /usr/src/sys/kern/vfs_bio.c:2442 >> 2nd 0xd80e5c80 bufwait (bufwait) @ /usr/src/sys/kern/vfs_bio.c:2456 >> KDB: stack backtrace: >> db_trace_self_wrapper(c0b46739,c3d9c78c,c07cf01e,c0b48fa6,d80e5c80,...) >> at db_trace_self_wrapper+0x26 >> kdb_backtrace(c0b48fa6,d80e5c80,c0b4dbf8,c0b4dbf8,c0b4d1a7,...) at >> kdb_backtrace+0x29 >> witness_checkorder(d80e5c80,9,c0b4d1a7,998,4,...) at >> witness_checkorder+0x6ee >> __lockmgr_args(d80e5c80,81900,c4225b20,c0b4db54,50,...) at >> __lockmgr_args+0x7a8 >> getblk(c4225a78,0,0,800,0,...) at getblk+0x16e >> breadn(c4225a78,0,0,800,0,...) at breadn+0x44 >> bread(c4225a78,0,0,800,0,...) at bread+0x4c >> ffs_blkatoff(c4225a78,0,0,0,c3d9c9a8,...) at ffs_blkatoff+0xdf >> ufs_lookup(c3d9c9ec,c4225a78,0,c4225a78,c3d9ca0c,...) at ufs_lookup+0x2e5 >> VOP_CACHEDLOOKUP_APV(c0c20aa0,c3d9c9ec,c3d9cb50,c3d9cb3c,c40a3400,...) at >> VOP_CACHEDLOOKUP_APV+0xa5 >> vfs_cache_lookup(c3d9ca6c,c3d9ca6c,500000c,80000,c4225a78,...) at >> vfs_cache_lookup+0xd7 >> VOP_LOOKUP_APV(c0c20aa0,c3d9ca6c,c0b4e9dd,1b0,c3d9cb3c,...) at >> VOP_LOOKUP_APV+0xa5 >> lookup(c3d9cb24,c0b4e9dd,d8,c0,c40a352c,...) at lookup+0x59e >> namei(c3d9cb24,c3d9cb28,c07ce7ec,0,c0cbeaf0,...) at namei+0x47b >> kern_unlinkat(c409ed20,ffffff9c,c0b4f074,1,c3d9cc5c,...) at >> kern_unlinkat+0x46 >> kern_unlink(c409ed20,c0b4f074,1,62c,0,...) at kern_unlink+0x27 >> vfs_mountroot_try(c0b4f22e,c0b3cf7c,c0b359ed,1,c080cf40,...) at >> vfs_mountroot_try+0x472 >> vfs_mountroot(c0c6a5d0,4,c0b3e263,264,0,...) at vfs_mountroot+0x409 >> start_init(0,c3d9cd38,c0b3fbac,324,c409cd0c,...) at start_init+0x65 >> fork_exit(c0756550,0,c3d9cd38) at fork_exit+0xc5 >> fork_trampoline() at fork_trampoline+0x8 >> --- trap 0, eip = 0, esp = 0xc3d9cd70, ebp = 0 --- >> start_init: trying /sbin/init >> bge0: link state changed to DOWN >> bge0: link UP >> bge0: link state changed to UP >> bge1: link state changed to DOWN -- Mark Atkinson atkin901@yahoo.com (!wired)?(coffee++):(wired);
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?g94ko8$8v4$1>