Date: Wed, 19 Aug 1998 09:46:29 +0200 (CEST) From: Dirk-Willem van Gulik <dirk.vangulik@jrc.it> To: John <freebsd-root@i-zone.demon.co.uk> Cc: freebsd-questions@FreeBSD.ORG, freebsd-mobile@FreeBSD.ORG Subject: Re: XFree fullscreen on laptop problems (CT65548 chipset) Message-ID: <Pine.BSF.3.96.980819094519.15617Y-100000@elpc36.jrc.it> In-Reply-To: <9XmjECAXbK21EwbF@i-zone.demon.co.uk>
next in thread | previous in thread | raw e-mail | index | archive | help
Check might want to check the manual, the 112CT model as an Fn+F key short cut to make the screen bigger/smaller. Once done, it stays that way, across reboots, until the battery goes really dry. DW On Mon, 17 Aug 1998, John wrote: > Hello Experts > > (also cc'd to freebsd-mobile) > > OK. This one has me doing the headless chicken dance. > > I have got X to work on my laptop OK, the final problem is getting it to > use the entire screen. The screen is an 11" TFT screen on a Toshiba > Satellite 110CT laptop. The video card is a chips & technologies CT65548 > (1 MB). I am using the SVGA server with Xfree 3.3.2.2 on FreeBSD > 2.2.7-RELEASE > > The problem is that though it loads into 800x600@8bpp there is a 1 inch > gap around the entire screen. I have played with the option settings > below with the help from the c&t section of the xfree86 website. The > lcd-center option is required otherwise the display is shifted to the > left corner. > > I calculate that I would have to have more than 1MB video ram to run at > better than 800x600@8bpp - am I correct? > > I hope the stuff below gives you enough information. I have exhausted my > expertise in this area. The first bit is the relevant section from > XF86Config, the second bit is standard error when startx is invoked. > > Any thoughts on this, or a XF86Config known to work with this chipset, > are appreciated. > > Thanks > > # Device configured by xf86config: > Section "Device" ] > Identifier "Chips & Technologies CT65548" > VendorName "chips & technologies" > BoardName "CT65548" > VideoRam 1024 > # Option "noaccel" > # Option "no_bitblt" > # Option "xaa_no_color_exp" > Option "xaa_benchmark" > # Option "sw_cursor" > # Option "mmio" > # Option "use_18bit_bus" > Option "hw_clocks" > # Textclockfreq 25.175 > # Option "nolinear" > # MemBase 0x03b00000 > # Device section for C&T cards. > Option "lcd_center" > Option "suspend_hack" > # Option "STN" > # Option "no_stretch" > # Option "no_center" > # Option "use_modeline" > # Option "fix_panel_size" > # videoram 512 > # Insert Clocks lines here if appropriate > EndSection > # ********************************************************************** > # Screen sections > # ********************************************************************** > # The Colour SVGA serverSection > "Screen" Driver "svga" > # Use Device "Generic VGA" for Standard VGA 320x200x256 > #Device "Generic VGA" > Device "Chips & Technologies CT65548" > Monitor "toshiba lcd panel" > Subsection "Display" > Depth 8 > # Omit the Modes line for the "Generic VGA" device > Modes "640x480" "800x600" "1024x768" > ViewPort 0 0 > # Use Virtual 320 200 for Generic VGA > EndSubsection > > Subsection "Display" > Depth 16 > Modes "640x480" "800x600" > ViewPort 0 0 > EndSubsection > > Subsection "Display" > Depth 24 > Modes "640x480" > ViewPort 0 0 > EndSubsection > EndSection > > # The 16-color VGA server > Section "Screen" > Driver "vga16" > Device "Generic VGA" > Monitor "toshiba lcd panel" > Subsection "Display" > Modes "640x480" "800x600" > ViewPort 0 0 > Virtual 800 600 > EndSubsection > EndSection > > # The Mono server > Section "Screen" > Driver "vga2" > Device "Generic VGA" > Monitor "toshiba lcd panel" > Subsection "Display" > Modes "640x480" "800x600" > ViewPort 0 0 > Virtual 800 600 > EndSubsection > EndSection > > # The accelerated servers (S3, Mach32, Mach8, 8514, P9000, AGX, W32, > #Mach64) > > Section "Screen" > Driver "accel" > Device "Chips & Technologies CT65548" > Monitor "toshiba lcd panel" > Subsection "Display" > Depth 8 > Modes "800x600" "1024x768" > ViewPort 0 0 > EndSubsection > > Subsection "Display" > Depth 16 > Modes "800x600" > ViewPort 0 0 > EndSubsection > EndSection > > > > XFree86 Version 3.3.2.3 / X Window System(protocol Version 11, revision > 0, vendor release 6300)Release Date: July 15 1998 If the server is > older than 6-12 months, or if your card is newer than the above > date, look for a newer version before reporting problems.(see http://www > .XFree86.Org/FAQ)Operating System: FreeBSD 2.2.5-STABLE i386 Configured > drivers: SVGA: server for SVGA graphics adaptors (Patchlevel 0): NV1, > STG2000, RIVA128, ET4000, ET4000W32, ET4000W32i,ET4000W32i_rev_b, > ET4000W32i_rev_c, ET4000W32p, ET4000W32p_rev_a, ET4000W32p_rev_b, > ET4000W32p_rev_c, ET4000W32p_rev_d, ET6000, ET6100, et3000, pvga1, > wd90c00, wd90c10, wd90c30, wd90c24, wd90c31, wd90c33, gvga, ati, > sis86c201, sis86c202, sis86c205, tvga8200lx, tvga8800cs, tvga8900b, > tvga8900c, tvga8900cl, tvga8900d, tvga9000, tvga9000i, tvga9100b, > tvga9200cxr, tgui9400cxi, tgui9420, tgui9420dgi, tgui9430dgi, > tgui9440agi, cyber9320, tgui9660, tgui9680, tgui9682, tgui9685, > cyber9382, cyber9385, cyber9388, cyber9397, cyber9520, 3dimage975, > 3dimage985, clgd5420, clgd5422, clgd5424, clgd5426, clgd5428, > clgd5429, clgd5430, clgd5434, clgd5436, clgd5446, clgd5480, > clgd5462, clgd5464, clgd5465, clgd6205, clgd6215, clgd6225, clgd6235, > clgd7541, clgd7542, clgd7543, clgd7548, clgd7555, ncr77c22, ncr77c22e, > cpq_avga, mga2064w, mga1064sg, mga2164w, mga2164w AGP, oti067, oti077, > oti087, oti037c, al2101, ali2228, ali2301, ali2302, ali2308, ali2401, > cl6410, cl6412, cl6420, cl6440, video7, ark1000vl, ark1000pv, > ark2000pv, ark2000mt, mx, realtek, AP6422, AT24, AT3D, s3_virge, > s3_svga, ct65520, ct65525, ct65530, ct65535, ct65540, ct65545, > ct65546, ct65548, ct65550, ct65554, ct65555, ct68554, ct64200, > ct64300, genericUsing syscons driver with X support (version 2.0)(using > VT number 4)XF86Config: /etc/XF86Config > > (**) stands for supplied, (--) stands for probed/default values > > (**) XKB: keycodes: "xfree86" > (**) XKB: types: "default" > (**) XKB: compat: "default" > (**) XKB: symbols: "en_US(pc102)+gb" > (**) XKB: geometry: "pc" > (**) Mouse: type: MouseSystems, device: /dev/sysmouse, baudrate: 1200 > (**) Mouse: buttons: 3, 3 button emulation (timeout: 50ms) > (**) SVGA: Graphics device ID: "Chips & Technologies CT65548" > (**) SVGA: Monitor ID: "toshiba lcd panel" > (--) SVGA: Mode "640x400" needs vert refresh rate of 69.93 Hz. Deleted. > (--) SVGA: Mode "800x600" needs hsync freq of 35.16 kHz. Deleted. > (--) SVGA: Mode "1024x768" needs hsync freq of 35.52 kHz. Deleted. > (--) SVGA: Mode "640x400" needs hsync freq of 37.86 kHz. Deleted. > (--) SVGA: Mode "640x480" needs hsync freq of 36.46 kHz. Deleted. > (--) SVGA: Mode "640x480" needs hsync freq of 37.50 kHz. Deleted. > (--) SVGA: Mode "800x600" needs hsync freq of 37.88 kHz. Deleted. > (--) SVGA: Mode "640x400" needs hsync freq of 43.27 kHz. Deleted. > (--) SVGA: Mode "1152x864" needs hsync freq of 43.92 kHz. Deleted. > (--) SVGA: Mode "800x600" needs hsync freq of 48.08 kHz. Deleted. > (--) SVGA: Mode "1024x768" needs hsync freq of 48.36 kHz. Deleted. > (--) SVGA: Mode "640x480" needs hsync freq of 53.01 kHz. Deleted. > (--) SVGA: Mode "1152x864" needs hsync freq of 53.51 kHz. Deleted. > (--) SVGA: Mode "800x600" needs hsync freq of 55.84 kHz. Deleted. > (--) SVGA: Mode "1024x768" needs hsync freq of 56.48 kHz. Deleted. > (--) SVGA: Mode "1280x1024" needs hsync freq of 51.02 kHz. Deleted. > (--) SVGA: Mode "800x600" needs hsync freq of 64.02 kHz. Deleted. > (--) SVGA: Mode "1024x768" needs hsync freq of 62.50 kHz. Deleted. > (--) SVGA: Mode "1152x864" needs hsync freq of 62.42 kHz. Deleted. > (--) SVGA: Mode "1280x1024" needs hsync freq of 64.25 kHz. Deleted. > (--) SVGA: Mode "1024x768" needs hsync freq of 70.24 kHz. Deleted. > (--) SVGA: Mode "1152x864" needs hsync freq of 70.88 kHz. Deleted. > (--) SVGA: Mode "1280x1024" needs hsync freq of 74.59 kHz. Deleted. > (--) SVGA: Mode "1600x1200" needs hsync freq of 75.00 kHz. Deleted. > (--) SVGA: Mode "1152x864" needs hsync freq of 76.01 kHz. Deleted. > (--) SVGA: Mode "1280x1024" needs hsync freq of 78.86 kHz. Deleted. > (--) SVGA: Mode "1024x768" needs hsync freq of 80.21 kHz. Deleted. > (--) SVGA: Mode "1280x1024" needs hsync freq of 81.13 kHz. Deleted. > (--) SVGA: Mode "1600x1200" needs hsync freq of 87.50 kHz. Deleted. > (--) SVGA: Mode "1152x864" needs hsync freq of 89.62 kHz. Deleted. > (--) SVGA: Mode "1280x1024" needs hsync freq of 91.15 kHz. Deleted. > (--) SVGA: Mode "1600x1200" needs hsync freq of 93.75 kHz. Deleted. > (--) SVGA: Mode "1600x1200" needs hsync freq of 105.77 kHz. Deleted. > (--) SVGA: Mode "1280x1024" needs hsync freq of 107.16 kHz. Deleted. > (--) SVGA: Mode "1800X1440" needs hsync freq of 96.15 kHz. Deleted. > (--) SVGA: Mode "1800X1440" needs hsync freq of 104.52 kHz. Deleted. > (--) SVGA: Mode "512x384" needs vert refresh rate of 77.97 Hz. Deleted. > (--) SVGA: Mode "512x384" needs vert refresh rate of 85.09 Hz. Deleted. > (--) SVGA: Mode "320x200" needs vert refresh rate of 69.93 Hz. Deleted. > (--) SVGA: Mode "320x240" needs hsync freq of 39.38 kHz. Deleted. > (--) SVGA: Mode "400x300" needs hsync freq of 35.16 kHz. Deleted. > (--) SVGA: Mode "400x300" needs hsync freq of 37.88 kHz. Deleted. > (--) SVGA: Mode "400x300" needs hsync freq of 48.08 kHz. Deleted. > (--) SVGA: Mode "480x300" needs hsync freq of 35.16 kHz. Deleted. > (--) SVGA: Mode "480x300" needs hsync freq of 37.80 kHz. Deleted. > (--) SVGA: Mode "480x300" needs hsync freq of 39.56 kHz. Deleted. > (--) SVGA: Mode "480x300" needs hsync freq of 48.00 kHz. Deleted. > (**) FontPath set to "/usr/X11R6/lib/X11/fonts/misc/,/usr/X11R6/lib/X11/ > fonts/75dpi/:unscaled,/usr/X11R6/lib/X11/fonts/100dpi/:unscaled,/usr/X11 > R6/lib/X11/fonts/75dpi/,/usr/X11R6/lib/X11/fonts/100dpi/" > > (--) SVGA: CHIPS: chip revision: 4 > (--) SVGA: Chipset: ct65548 > (--) SVGA: CHIPS: no monitor detected. > (**) SVGA: CHIPS: 1024 kB VRAM > (--) SVGA: CHIPS: TFT probed. > (--) SVGA: CHIPS: LCD > (--) SVGA: CHIPS: Display Size: x=800; y=600 > (--) SVGA: CHIPS: VL Bus > (--) SVGA: CHIPS: base address is set at 0x7800000. > (--) SVGA: CHIPS: Linear addressing is enabled at 0x7800000. > (--) SVGA: CHIPS: syncronous reset ignored. > (--) SVGA: CHIPS: Textmode Clock: 4. > (--) SVGA: chipset: ct65548 > (**) SVGA: videoram: 1024k > (--) SVGA: clocks: 25.17 28.32 31.50 35.49 40.09 > (**) SVGA: Option "hw_clocks" > (**) SVGA: Option "lcd_center" > (**) SVGA: Option "lcd_centre" > (**) SVGA: Option "xaa_benchmark" > (**) SVGA: Option "suspend_hack" > (**) SVGA: Using 8 bpp, Depth 8, Color weight: 666 > (--) SVGA: Maximum allowed dot-clock: 80.000 MHz > (**) SVGA: Mode "640x480": mode clock = 25.175, clock used = 25.170 > (--) SVGA: There is no mode definition named "800x600" > (--) SVGA: Removing mode "800x600" from list of valid modes. > (--) SVGA: There is no mode definition named "1024x768" > (--) SVGA: Removing mode "1024x768" from list of valid modes. > (--) SVGA: Virtual resolution set to 640x480 > (--) SVGA: SpeedUp code selection modified because virtualX != 1024 > (--) SVGA: CHIPS: 741376 bytes off-screen memory available > (--) SVGA: CHIPS: H/W cursor selected > (--) SVGA: CHIPS: SpeedUps selected (Flags=0xF) > (--) SVGA: Using XAA (XFree86 Acceleration Architecture) > (--) SVGA: XAA: Solid filled rectangles > (--) SVGA: XAA: Screen-to-screen copy > (--) SVGA: XAA: 8x8 pattern fill > (--) SVGA: XAA: 8x8 color expand pattern fill > (--) SVGA: XAA: CPU to screen color expansion (bitmap, TE/NonTE > imagetext, TE/NonTE polytext) > > (--) SVGA: XAA: Using 5 128x128 areas for pixmap caching > (--) SVGA: XAA: Caching tiles and stipples > (--) SVGA: XAA: Horizontal and vertical lines and segmentsCPU to > framebuffer > > 13.28 Mpix/sec (13.28 MB/s)10x1 solid rectangle fill > 4.36 Mpix/sec (4.36 MB/s)40x40 solid rectangle fill > 59.96 Mpix/sec (59.96 MB/s)400x400 solid rectangle fill > 93.36 Mpix/sec (93.36 MB/s)10x10 screen copy > 16.45 Mpix/sec (16.45 MB/s)40x40 screen copy > 37.59 Mpix/sec (37.59 MB/s)400x400 screen copy > 33.17 Mpix/sec (33.17 MB/s)400x400 aligned screen copy (scroll) > 40.78 Mpix/sec (40.78 MB/s)10x10 8x8 pattern fill > 13.00 Mpix/sec (13.00 MB/s)400x400 8x8 pattern fill > 87.34 Mpix/sec (87.34 MB/s)10x10 8x8 color expand pattern fill > 19.62 Mpix/sec (19.62 MB/s)400x400 8x8 color expand pattern fill > 93.97 Mpix/sec (93.97 MB/s)10x10 CPU-to-screen color expand > 2.02 Mpix/sec (2.02 MB/s)416x400 CPU-to-screen color expand > 93.78 Mpix/sec (93.78 MB/s) > > waiting for X server to shut down X connection to :0.0 broken (explicit > kill or server shutdown). > xterm: fatal IO error 32 (Broken pipe) or KillClient on X server ":0.0" > xterm: fatal IO error 32 (Broken pipe) or KillClient on X server ":0.0" > > -- > John > > To Unsubscribe: send mail to majordomo@FreeBSD.org > with "unsubscribe freebsd-mobile" in the body of the message > To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.BSF.3.96.980819094519.15617Y-100000>