Date: Thu, 28 Oct 2021 16:53:29 -0700 From: Mark Millard via freebsd-arm <freebsd-arm@freebsd.org> To: bob prohaska <fbsd@www.zefox.net> Cc: Free BSD <freebsd-arm@freebsd.org>, freebsd-ports@freebsd.org Subject: Re: Troubles booting Pi2 from USB using bootcode.bin method Message-ID: <D8DC329F-DFE4-4542-AA4D-87C41A50C8A4@yahoo.com> In-Reply-To: <7AC0733A-3FC9-4FA6-A6D7-0689A8ACB4CA@yahoo.com> References: <20211025034332.GA8398@www.zefox.net> <20211027162852.GA16010@www.zefox.net> <F54AB76B-83AE-40BD-B035-F35C7B898357@yahoo.com> <41C0A656-D898-4381-BB81-034D54CA04A0@yahoo.com> <02806205-6685-41FD-B2D1-415C82FBCF92@yahoo.com> <C99139A0-09A9-4A5E-AB53-719E07C16A22@yahoo.com> <20211028191635.GA19540@www.zefox.net> <7AC0733A-3FC9-4FA6-A6D7-0689A8ACB4CA@yahoo.com>
next in thread | previous in thread | raw e-mail | index | archive | help
On 2021-Oct-28, at 15:21, Mark Millard <marklmi at yahoo.com> wrote: > On 2021-Oct-28, at 12:16, bob prohaska <fbsd@www.zefox.net> wrote: > >> To make a clean start on this thread I've turned on the UART >> for bootcode.bin per Mark's instructions and done a few boot >> attempts with the USB2 and USB3 mechanical disks, singly and >> in unison. >> >> The bootlogs are in >> http://www.zefox.net/~fbsd/rpi2/bootproblems/ >> >> An immediate curiosity is that on the first try, booting >> with the USB3 device alone worked. I didn't record that >> output, unfortunately. > > Hmm. Too bad. > >> The second attempt failed, as expected, >> and is recorded in bootlog-fail. The third attempt booted both >> USB2 and USB3 disks together, recorded in bootlog.success. > > The two logs do not have the same set of dtdebug messages > for loading bcm2709-rpi-2-b.dtb . This is long before > u-boot.bin is loaded and so is during the RPi* firmware > time frame not u_Boot or FreeBSD;s loader or FreeBSD's kernel > or FreeBSD's world. > > From this I infer that there are two different msdosfs's > wtith differing content on the 2 drives and when both > drives are in place . > > You have not reported on the following for either drive's > msdosfs : > > # strings ???/start.elf | grep "VC_BUILD_" > > Another thing of interest would be something like (both > msdosfs mounts): > > # diff -rq ... ... > > in order to see what files have distinctions on the > two media. A diff of the two config.txt files would be > relevant (no -q involvement). > > >> I'm trying to build u-boot-rpi2 and will try to update the USB3 >> disk with it once complete. >> >> The actual boot sequence using bootcode.bin is still a bit hazy: >> Is it microSD/dos -> USB/dos ->USB/freebsd ? >> > > Based on the log file for success the ordering is > > bootcode.bin from the microsd card > config.txt (also re-read multiple times later, not listed) > start.elf > fixup.dat > bcm2709-rpi-2-b.dtb > overlays/mmc.dtbo > cmdline.txt (if it exists) > u-boot.bin > efi/boot/bootarm.efi > efi/freebsd/loader.env > /boot/defaults/loader.conf > /boot/device.hints > /boot/loader.conf > /boot/loader.conf.local > /boot/boot/kernel > /boot/kernel/fi.lemon.ko > /boot/kernel/umodem.ko > FreeBSD world > > > However the failing one has the following involved > (I omit various lines): > > . . . > Loading 'bcm2709-rpi-2-b.dtb' to 0x100 size 0x6879 > Unknown dtparam 'pwr_led_gpio' - ignored > dterror: no symbols found > dtdebug: /__overrides__ node not found > Unknown dtparam 'uart0_clkrate' - ignored > dtdebug: Opened overlay file 'overlays/mmc.dtbo' > brfs: File read: /mfs/sd/overlays/mmc.dtbo > dterror: not a valid FDT - err -9 > . . . > > That seqeunce makes no mention of: "using platform 'bcm2835'" > and the like. An example is: "found override pwr_led_gpio". > > Again, all this looks like tehre are two msdosfs involved and > the two are not the same by content. > Another possibility is that you have more in the microsd card's msdosfs than just bootcode.bin so that that microsd card might be the source of alternative files. (That makes up to 3 media that might be sources of files.) === Mark Millard marklmi at yahoo.com ( dsl-only.net went away in early 2018-Mar)
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?D8DC329F-DFE4-4542-AA4D-87C41A50C8A4>