From owner-freebsd-hardware Fri Jul 20 20: 7:54 2001 Delivered-To: freebsd-hardware@freebsd.org Received: from mtiwmhc23.worldnet.att.net (mtiwmhc23.worldnet.att.net [204.127.131.48]) by hub.freebsd.org (Postfix) with ESMTP id 9522937B403 for ; Fri, 20 Jul 2001 20:07:51 -0700 (PDT) (envelope-from achornback@worldnet.att.net) Received: from tomcat ([12.93.210.161]) by mtiwmhc23.worldnet.att.net (InterMail vM.4.01.03.16 201-229-121-116-20010115) with SMTP id <20010721030750.UTAL1777.mtiwmhc23.worldnet.att.net@tomcat>; Sat, 21 Jul 2001 03:07:50 +0000 From: "Andrew C. Hornback" To: "Jamie Hermans" , Subject: RE: Compaq Smart 2/E Controller Support... Date: Fri, 20 Jul 2001 23:00:20 -0400 Message-ID: <002901c11191$47432f40$0e00000a@tomcat> MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit X-Priority: 3 (Normal) X-MSMail-Priority: Normal X-Mailer: Microsoft Outlook 8.5, Build 4.71.2173.0 In-Reply-To: <5.1.0.14.2.20010720204350.00a78460@imap> X-MimeOLE: Produced By Microsoft MimeOLE V5.00.2919.6600 Importance: Normal Sender: owner-freebsd-hardware@FreeBSD.ORG Precedence: bulk List-ID: List-Archive: (Web Archive) List-Help: (List Instructions) List-Subscribe: List-Unsubscribe: X-Loop: FreeBSD.org > -----Original Message----- > From: owner-freebsd-hardware@FreeBSD.ORG > [mailto:owner-freebsd-hardware@FreeBSD.ORG]On Behalf Of Jamie Hermans > Sent: Friday, July 20, 2001 10:49 PM > To: stable@freebsd.org; hardware@freebsd.org > Subject: Compaq Smart 2/E Controller Support... > > Hi.... > > Reading through > http://seeberg.dk/freebsd/idaraid/smart-2_controllers.html, > I noticed the line: "The EISA controllers are not supported yet." > > Has the ida driver been "fixed" yet, in regards to EISA controllers (the > Compaq Smart 2/E in particular)? It doesn't appear so as of > 4.3-RELEASE, which identifies the controller on boot up, and then > promptly panics :( > > An alternative I guess, is to use the old 3.x (non-newbus) driver > ... but how? Not sure if this applies to your EISA card, but I do have a PCI version of that card in a ProLiant 1500. It takes a little "jockeying" around to make the ida driver work, but it does work fine. Have you tried installing FreeBSD similarly to the way you would with the PCI controller? With my controller before I learned the tricks to make it work, it would panic at that point as well, because Compaq's ultimate wisdom, they use the same vector addresses for the SMART 2/x controllers as the rest of the world uses for a standard IDE controller. Try doing an install treating it like the PCI version, and see if that works. It's worth a shot, right? That's my best guess... --- Andy To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-hardware" in the body of the message