Skip site navigation (1)Skip section navigation (2)
Date:      Fri, 22 Jul 2005 22:06:27 -0400
From:      "Ray Rogers" <ilbthere@comcast.net>
To:        <freebsd-stable@freebsd.org>
Subject:   ATA issue on 5.4
Message-ID:  <000001c58f2b$2438e000$1900a8c0@pepe>

Next in thread | Raw E-Mail | Index | Archive | Help
Greetings all.   I would appreciate any incite that you can give me with
this problem.

=20

I am sure that you have visited this issue in the past, but I have been
unable to find a resolution.  The symptoms are

            ad1: TIMEOUT - READ_DMA retrying (2 retries left) =
LBA=3D10027551

            ad0: WARNING - removed from configuration

            ad1: WARNING - removed from configuration

            ata0-slave: FAILURE - READ_DMA timed out

=20

After these messages the machine is unusable until it is power cycled.

=20

=20

The machine can is described by dmesg below, but here is some history.  =
The
machine has been running FreeBSD 4.8 - 4.10 for the last several years =
with
two disks on the ATA0 controller. (ad0=3D Maxtor 51024H2 10GB, =
ad1=3DWD400BB
40GB) =20

=20

I finally decided it was time to move to 5.x release.  I also decided it =
was
time to upgrade the disks I used a Maxtor 20GB for ad0 and WD2500JB for =
ad1.
The Maxtor disk has been used before but the WD is brand new. =20

=20

The machine is a 733 MHz Compaq Deskpro EN (Intel 815e chipset with an =
ICH 2
ata controller).  I have turned off all power management functions in =
the
CMOS. I am currently running the GENERIC Kernel as taken from the 5.4 =
ISO
install.  I upgraded to p4 but it did not help my situation so I backed =
off.
I have searched high and low and have found a suggestion of adding a =
command
to the /boot/loader.conf to no avail.   I do not believe that the issue =
is
the ata controller, however, it could have to do with compatibility with =
the
250GB WD drive with FreeBSD.  I have not used the WD before but I have
tested it with Western Digital's Data Lifeguard Diagnostics as it was
installed in the box for both communication and media errors with no =
errors
found.

=20

The issue seems to occur when the system has been idle for some time (an
hour or so).

=20

Below is my dmesg output.  I do not want to reload 4.10 to have a =
working
system.=20

=20

 Thanks for the help.

=20

Ray

=20

=20

Copyright (c) 1992-2005 The FreeBSD Project.

Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994

      The Regents of the University of California. All rights reserved.

FreeBSD 5.4-RELEASE #0: Sun May  8 10:21:06 UTC 2005

    root@harlow.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC

Timecounter "i8254" frequency 1193182 Hz quality 0

CPU: Intel Pentium III (730.90-MHz 686-class CPU)

  Origin =3D "GenuineIntel"  Id =3D 0x683  Stepping =3D 3

=20
Features=3D0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE=
,MCA,
CMOV,PAT,PSE36,MMX,FXSR,SSE>

real memory  =3D 535822336 (511 MB)

avail memory =3D 514658304 (490 MB)

MPTable: <COMPAQ   Deskpro     >

ioapic0: Changing APIC ID to 8

ioapic0: Assuming intbase of 0

ioapic0 <Version 2.0> irqs 0-23 on motherboard

npx0: <math processor> on motherboard

npx0: INT 16 interface

cpu0 on motherboard

pcib0: <MPTable Host-PCI bridge> pcibus 0 on motherboard

pci0: <PCI bus> on pcib0

agp0: <Intel 82815 (i815 GMCH) SVGA controller> mem
0x40500000-0x4057ffff,0x44000000-0x47ffffff irq 16 at device 2.0 on pci0

pcib1: <MPTable PCI-PCI bridge> at device 30.0 on pci0

pci2: <PCI bus> on pcib1

fxp0: <Intel 82801BA/CAM (ICH2/3) Pro/100 Ethernet> port 0x1000-0x103f =
mem
0x40100000-0x40100fff irq 20 at device 8.0 on pci2

miibus0: <MII bus> on fxp0

inphy0: <i82562EM 10/100 media interface> on miibus0

inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto

fxp0: Ethernet address: 00:50:8b:d8:70:af

fxp1: <Intel 82559 Pro/100 Ethernet> port 0x1040-0x107f mem
0x40000000-0x400fffff,0x40200000-0x40200fff irq 18 at device 9.0 on pci2

miibus1: <MII bus> on fxp1

inphy1: <i82555 10/100 media interface> on miibus1

inphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto

fxp1: Ethernet address: 00:d0:b7:0f:a7:f4

isab0: <PCI-ISA bridge> at device 31.0 on pci0

isa0: <ISA bus> on isab0

atapci0: <Intel ICH2 UDMA100 controller> port
0x2460-0x246f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 31.1 on pci0

ata0: channel #0 on atapci0

ata1: channel #1 on atapci0

uhci0: <Intel 82801BA/BAM (ICH2) USB controller USB-B> port =
0x2440-0x245f
irq 23 at device 31.4 on pci0

usb0: <Intel 82801BA/BAM (ICH2) USB controller USB-B> on uhci0

usb0: USB revision 1.0

uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1

uhub0: 2 ports with 2 removable, self powered

pcm0: <Intel ICH2 (82801BA)> port 0x2400-0x243f,0x2000-0x20ff irq 17 at
device 31.5 on pci0

pcm0: <Analog Devices AD1885 AC97 Codec>

orm0: <ISA Option ROMs> at iomem
0xe0000-0xeffff,0xcb000-0xd87ff,0xca000-0xcafff,0xc0000-0xc9fff on isa0

pmtimer0 on isa0

atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0

atkbd0: <AT Keyboard> irq 1 on atkbdc0

kbd0 at atkbd0

psm0: <PS/2 Mouse> irq 12 on atkbdc0

psm0: model IntelliMouse, device ID 3

fdc0: <Enhanced floppy controller> at port 0x3f0-0x3f5 irq 6 drq 2 on =
isa0

fd0: <1440-KB 3.5" drive> on fdc0 drive 0

ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0

ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode

ppc0: FIFO with 16/16/13 bytes threshold

ppbus0: <Parallel port bus> on ppc0

plip0: <PLIP network interface> on ppbus0

lpt0: <Printer> on ppbus0

lpt0: Interrupt-driven port

ppi0: <Parallel I/O> on ppbus0

sc0: <System console> at flags 0x100 on isa0

sc0: VGA <16 virtual consoles, flags=3D0x300>

sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0

sio0: type 16550A

sio1 at port 0x2f8-0x2ff irq 3 on isa0

sio1: type 16550A

vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on =
isa0

unknown: <PNP0401> can't assign resources (port)

unknown: <PNP0501> can't assign resources (port)

unknown: <PNP0501> can't assign resources (port)

unknown: <PNP0700> can't assign resources (port)

unknown: <PNP0303> can't assign resources (port)

unknown: <PNP0f13> can't assign resources (irq)

Timecounter "TSC" frequency 730899496 Hz quality 800

Timecounters tick every 10.000 msec

ad0: 19092MB <MAXTOR 6L020J1/A93.0500> [38792/16/63] at ata0-master =
UDMA100

ad1: 238475MB <WDC WD2500JB-00GVA0/08.02D08> [484521/16/63] at =
ata0-slave
UDMA100

acd0: CDROM <LTN323/DQ19> at ata1-master PIO4

pcm0: measured ac97 link rate at 55931 Hz

Mounting root from ufs:/dev/ad0s1a

WARNING: / was not properly dismounted

WARNING: /home was not properly dismounted

WARNING: /usr was not properly dismounted

WARNING: /usr/local was not properly dismounted

WARNING: /var was not properly dismounted

=20

I=20

=20




Want to link to this message? Use this URL: <http://docs.FreeBSD.org/cgi/mid.cgi?000001c58f2b$2438e000$1900a8c0>