Date: Tue, 8 Oct 2013 09:33:59 +0900 From: Yonghyeon PYUN <pyunyh@gmail.com> To: Kurt Buff <kurt.buff@gmail.com> Cc: freebsd-net@freebsd.org Subject: Re: Problem with Lenovo SL500 Message-ID: <20131008003359.GA3162@michelle.cdnetworks.com> In-Reply-To: <CADy1Ce73mrmTiA6sX34HAsa0ihdOYXAEtsyEYXWYBKfS1D_XpQ@mail.gmail.com> References: <CADy1Ce73mrmTiA6sX34HAsa0ihdOYXAEtsyEYXWYBKfS1D_XpQ@mail.gmail.com>
next in thread | previous in thread | raw e-mail | index | archive | help
On Mon, Oct 07, 2013 at 03:14:58PM -0700, Kurt Buff wrote: > All, > > This machine has for its wired port a RealTek unit: > > re0: <RealTek 8168/8111 B/C/CP/D/DP/E/F PCIe Gigabit Ethernet> port > 0xe800-0xe8ff mem 0xfcfff000-0xfcffffff,0xfcfe0000-0xfcfeffff irq 19 > at device 0.0 on pci12 > re0: Using 1 MSI-X message > re0: ASPM disabled > re0: Chip rev. 0x3c000000 > re0: MAC rev. 0x00400000 > miibus0: <MII bus> on re0 > rgephy0: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on miibus0 > rgephy0: none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, > 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master, > 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, > 1000baseT-FDX-flow-master, auto, auto-flow > re0: Ethernet address: 00:26:18:45:77:51 > > > I've got wireless working for iwn (thanks Adrian!), and I'm trying to > use the wired NIC (re0) as an unnumbered port to monitor a mirror port > on an HP switch. However, when I connect it, it shows up as only > 10mbit, half-duplex on the switch, and it refuses to send packets. > > I've tried 'ifconfig re0 media 1000baseT -mediaopt full-duplex' > > with no particular luck, as it shows the following > > re0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 > options=8209b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAGIC,LINKSTATE> > ether 00:26:18:45:77:51 > nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> > media: Ethernet 1000baseT (10baseT/UTP <half-duplex>) > status: active > > I get no output from 'tcpdump -npi re0'. I get link light, and it > worked great on re0 when I did the install for FreeBSD, but no joy for > capturing packets from the switch. It seems you didn't UP the interface. And you may have to put the interface into promiscuous mode to capture all packets(i.e. remove -p option). > > Anyone have some thoughts to share on this? Yes, I tried using a new > cable, too... > > Kurt
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20131008003359.GA3162>