Date: Fri, 9 Apr 2004 13:13:51 +0200 From: Johan Pettersson <manlix@demonized.net> To: Jeff Doolittle <jdoolittle@kingsquarry.net> Cc: freebsd-current@freebsd.org Subject: Re: ASUS P4C800-E Deluxe and ICH5R support Message-ID: <20040409131351.3760f3b5.manlix@demonized.net> In-Reply-To: <4075E63C.3060709@kingsquarry.net> References: <4075E63C.3060709@kingsquarry.net>
next in thread | previous in thread | raw e-mail | index | archive | help
Try disabling APIC at the boot prompt. set hint.apic.0.disabled=1 On Thu, 08 Apr 2004 19:54:36 -0400 Jeff Doolittle <jdoolittle@kingsquarry.net> wrote: > I've seen eMails regarding ICH5R support on other motherboards being > added, is there plans to add support for the ASUS P4C800-E Deluxe? > > I tried both FreeBSD v5.2.1 & am now updating to current on a daily > basis hoping the following error will be address: > > ad12: TIMEOUT - WRITE_DMA retrying (2 retries left) LBA = xxxx > or > ad10: TIMEOUT - WRITE_DMA retrying (2 retries left) LBA = xxxx > and > the machine is hung, requiring a hard reset. > > The following are from dmesg: > > FreeBSD 5.2-CURRENT #0: Thu Apr 8 13:27:36 EDT 2004 > root@saturn.kingsquarry.net:/usr/obj/usr/src/sys/GENERIC > ..... > Timecounter "i8254" frequency 1193182 Hz quality 0 > CPU: Intel(R) Pentium(R) 4 CPU 2.40GHz (2398.85-MHz 686-class CPU) > Origin = "GenuineIntel" Id = 0xf25 Stepping = 5 > > Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR, > PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,P > BE> > Hyperthreading: 2 logical CPUs > real memory = 536018944 (511 MB) > avail memory = 514789376 (490 MB) > ..... > atapci0: <Promise PDC20378 SATA150 controller> port > 0xd880-0xd8ff,0xdfa0-0xdfaf,0xdf00-0xdf3f mem > 0xfeac0000-0xfeadffff,0xfeafe000-0xfeafefff irq 23 at device 4.0 on > pci3 ata2: at 0xfeafe000 on atapci0 > ata3: at 0xfeafe000 on atapci0 > ata4: at 0xfeafe000 on atapci0 > isab0: <PCI-ISA bridge> at device 31.0 on pci0 > isa0: <ISA bus> on isab0 > atapci1: <Intel ICH5 UDMA100 controller> port > 0xfc00-0xfc0f,0-0x3,0-0x7,0-0x3,0-0x7 at device 31.1 on pci0 > ata0: at 0x1f0 irq 14 on atapci1 > ata1: at 0x170 irq 15 on atapci1 > atapci2: <Intel ICH5 SATA150 controller> port > 0xef90-0xef9f,0xefa8-0xefab,0xefa0-0xefa7,0xefac-0xefaf,0xefe0-0xefe7 > irq 18 at device 31.2 on pci0 > ata5: at 0xefe0 on atapci2 > ata6: at 0xefa0 on atapci2 > ..... > ad0: 19092MB <ST320413A> [38792/16/63] at ata0-master UDMA100 > acd0: CDRW <48X12X50 CD-RW 1.04 20021101> at ata1-master PIO4 > ad4: 190782MB <WDC WD2000JD-00FYB0> [387621/16/63] at ata2-master > UDMA100 ad6: 190782MB <WDC WD2000JD-00FYB0> [387621/16/63] at > ata3-master UDMA100 em0: Link is up 100 Mbps Full Duplex > ad10: 190782MB <WDC WD2000JD-00FYB0> [387621/16/63] at ata5-master > UDMA100 ad12: 190782MB <WDC WD2000JD-00FYB0> [387621/16/63] at > ata6-master UDMA100 ar0: 381564MB <ATA RAID0 array> [48642/255/63] > status: READY subdisks: > disk0 READY on ad4 at ata2-master > disk1 READY on ad6 at ata3-master > ar1: 381564MB <ATA RAID0 array> [48642/255/63] status: READY subdisks: > disk0 READY on ad10 at ata5-master > disk1 READY on ad12 at ata6-master > > NOTE #1: ar0 is a Promise created RAID array. > NOTE #2: at1 is a atacontrol created RAID array, because the BIOS > created is not recognized. > > Basically the machine crashed when I run rsync from the Promise raid > drives to the Intel raid drives. In the past I could copy between 1 - > > 2gig and it would hang with the above error messages, except > yesterday's build dumped me in debug mode, today's build is the first > I have seen it acknowlegde the Intel ICH5 SATA150 controller and it > errors out almost immediately after starting rsync. > > Is there more information I can/should provide to help resolve this > problem? I apologize, this is the first time I've ever had a > "problem" with FreeBSD since I started using it at v2.2.7.... > > Thanks. > > - Jeff > > > > Thanks... > _______________________________________________ > freebsd-current@freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-current > To unsubscribe, send any mail to > "freebsd-current-unsubscribe@freebsd.org"
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20040409131351.3760f3b5.manlix>