Date: Wed, 4 Mar 1998 06:39:08 -0500 (EST) From: Gang-Ryung Uh <uh@nu.cs.fsu.edu> To: eroper@wanfear.com (Edward Roper) Subject: Re: 2.2.5 Installation Message-ID: <199803051221.HAA13590@xi.cs.fsu.edu> In-Reply-To: <19980303085715.53963@ns1.wanfear.com> from "Edward Roper" at Mar 3, 98 08:57:15 am
next in thread | previous in thread | raw e-mail | index | archive | help
Hello, after disconnecting the ZIP, I still stucked at the same point of installation with the same message (as shown before) Do you think any other device(s) for disconnection to make installation process to proceed. Thanks in advance. Regards, Gang-Ryung Uh > > If that ZIP drive is IDE you have to remove it, install FreeBSD and re- > attach the IDE zip drive. It's a known bug in FreeBSD. > > On Tue, Mar 03, 1998 at 08:04:39AM -0500, Gang-Ryung Uh wrote: > > Hello, > > > > Recently, I got a PC, MICRON millennia XKU. The following is the more > > detailed information about the PC: > > > > Processor Type: Pentium II > > Processor Speed: 266 MHz > > Total Memory 64 MB > > DISK 6449 MB > > > > CDROM -- SONY CD-ROM CDU771 > > Disk Drives > > -- Generic IDE DISK TYPE 40 > > -- Generic NEC FLOPPY DISK > > -- IOMEGA ZIP 100 > > DISPLAY Adapters > > -- Diamond Viper V330 > > Floppy Disk Controller > > -- Standard Floppy Disk Controller > > Hard Disk Controllers > > -- Interl 82371AB PCI Bus Master IDE Controller > > -- Primary IDE controller (dual fifo) > > -- Secondary IDE controller (dual info) > > Keyboard > > -- PC/AT Enhanced Keyboard (101/102 Key) > > Modem > > -- Sportster 56000 Fax Internal PNP > > Mouse > > -- Microsoft PS2 Mouse with Wheel > > Network Adapters > > -- 3Com Fast EtherLink XL 10/100Mb TX Ethernet Adapter > > Ports > > -- Communications Port (COM1) > > -- Printer Port (LPT1) > > Sound, video and game controllers > > -- YAMAHA OPL3-SAx GamePort > > -- YAMAHA OPL3-SAx Sound System > > ... > > USB > > -- Interl 82371AB PCI to USB Universal Host Controller > > -- USB Root Hub > > > > When I boot the system with FreeBSD 2.2.5 boot floppy, the installation > > process hang after displaying messages as shown before. Even though I > > resolved (?) the conflicts during the installation, I could not make > > BSD installed on the PC that I can access. Any help or advise will > > be appreciated. Thanks in advance. > > > > Regards, > > Gang-Ryung Uh > > > > > > ------------------- installation messages --------- > > > > avail memory = 61071350 (59640K bytes) > > Probing for devices on PCI bus 0: > > chip0 <generic PCI bridge (vendor=8086 device=7180 subclass=0)> rev 3 on pci0:0 > > chip1 <generic PCI bridge (vendor=8086 device=7181 subclass=4)> rev 3 on pci0:1 > > chip2 <generic PCI bridge (vendor=8086 device=7110 subclass=1)> rev 1 on pci0:7: > > 0 > > pci0:7:1: Intel Corporation, device=0x7111, class=storage (ide) [no driver assig > > ned] > > pci0:7:2: Intel Corporation, device=0x7112, class=0x0c, subclass=0x03 int d irq > > 11 [no driver assigned] > > chip3 <generic PCI bridge (vendor=8086 device=7113 subclass=128)> rev 1 on pci0: > > 7:3 > > vx0 <3COM 3C905 Fast Etherlink XL PCI> rev 0 int a irq 10 on pci0:13 > > > > HANG!!!!! > > > > To Unsubscribe: send mail to majordomo@FreeBSD.org > > with "unsubscribe freebsd-questions" in the body of the message > -- > Edward Roper <eroper@wanfear.com> > > WANfear > http://www.wanfear.com/ > To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?199803051221.HAA13590>