Skip site navigation (1)Skip section navigation (2)
Date:      Mon, 30 Aug 2004 17:17:35 +0200
From:      "Daniel Eriksson" <daniel_k_eriksson@telia.com>
To:        <freebsd-current@FreeBSD.org>
Cc:        =?iso-8859-1?Q?'S=F8ren_Schmidt'?= <sos@DeepCore.dk>
Subject:   ataraid + geom_stripe problems
Message-ID:  <!~!UENERkVCMDkAAQACAAAAAAAAAAAAAAAAABgAAAAAAAAA0VcX9IoJqUaXPS8MjT1PdsKAAAAQAAAAKptuZr9dAUWKvmgdFpGa0wEAAAAA@telia.com>

Next in thread | Raw E-Mail | Index | Archive | Help
This is a multi-part message in MIME format.

------=_NextPart_000_0000_01C48EB5.3E33BF60
Content-Type: text/plain;
	charset="iso-8859-1"
Content-Transfer-Encoding: 7bit


A few days ago I decided to try to switch from gvinum in RAID-0 mode to
geom_stripe on one of my arrays (4 x 36GB SCSI). Unfortunately I never
managed to get it to work since the machine protested loudly and crashed all
of my ataraid arrays whenever geom_stripe tried to start up its array. This
was on a 6-CURRENT system compiled from sources dated
2004.08.26.(something).

Has anyone tried to use both ataraid and geom_stripe on the same machine?

I also use gvinum on this machine, but it is not loaded during boot so it
should not affect this.

Attached is a dmesg from the machine (but with a slightly newer kernel, no
other changes were made though other than to remove geom_stripe). It should
provide info on what hardware is used.

Here's how it looked on the console when I tried it 3 days ago. The ataraid
discs all hang off of two HighPoint RocketRAID 454 cards. Once all the
atariad arrays had been crashed I could delete and re-create them without
any problems. I didn't dare to try to access them however (live data on the
filesystems).

ar0: 476950MB <ATA RAID0 array> [60802/255/63] status: READY subdisks:
 disk0 READY on ad4 at ata2-master
 disk1 READY on ad5 at ata2-slave
ar1: 478744MB <ATA RAID0 array> [61031/255/63] status: READY subdisks:
 disk0 READY on ad6 at ata3-master
 disk1 READY on ad7 at ata3-slave
ar2: 388962MB <ATA RAID0 array> [49585/255/63] status: READY subdisks:
 disk0 READY on ad9 at ata4-slave
 disk1 READY on ad8 at ata4-master
ar3: 228946MB <ATA RAID0 array> [29186/255/63] status: READY subdisks:
 disk0 READY on ad23 at ata11-slave
 disk1 READY on ad24 at ata12-master
Waiting 5 seconds for SCSI devices to settle
sa0 at ahc0 bus 0 target 5 lun 0
sa0: <Seagate STT20000N 6A51> Removable Sequential Access SCSI-2 device 
sa0: 10.000MB/s transfers (10.000MHz, offset 15)
da0 at ahc0 bus 0 target 10 lun 0
da0: <IBM DDYS-T36950N S93E> Fixed Direct Access SCSI-3 device 
da0: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing
Enabled
da0: 35003MB (71687340 512 byte sectors: 255H 63S/T 4462C)
da1 at ahc0 bus 0 target 11 lun 0
da1: <IBM IC35L036UWD210-0 S5CQ> Fixed Direct Access SCSI-3 device 
da1: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing
Enabled
da1: 35003MB (71687340 512 byte sectors: 255H 63S/T 4462C)
da2 at ahc0 bus 0 target 12 lun 0
da2: <IBM DDYS-T36950N S93E> Fixed Direct Access SCSI-3 device 
da2: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing
Enabled
da2: 35003MB (71687340 512 byte sectors: 255H 63S/T 4462C)
da3 at ahc0 bus 0 target 13 lun 0
da3: <IBM DDYS-T36950N S93E> Fixed Direct Access SCSI-3 device 
da3: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing
Enabled
da3: 35003MB (71687340 512 byte sectors: 255H 63S/T 4462C)
Mounting root from ufs:/dev/ad0s1a
Enter full pathname of shell or RETURN for /bin/sh: 
# kldload geom_stripe
# GEOM_STRIPE: Device testraid created (id=3167252550).
GEOM_STRIPE: Disk da3 attached to racingraid.
GEOM_STRIPE: Disk da2 attached to racingraid.
GEOM_STRIPE: Disk da1 attached to racingraid.
GEOM_STRIPE: Disk da0 attached to racingraid.
GEOM_STRIPE: Device testraid activated.
Interrupt storm detected on "irq16: atapci0+++"; throttling interrupt source

ad24: TIMEOUT - READ_DMA retrying (2 retries left) LBA=234441657
ad24: TIMEOUT - READ_DMA retrying (1 retry left) LBA=234441657
ad24: FAILURE - READ_DMA timed out
ar3: ERROR - array broken
ad8: TIMEOUT - READ_DMA retrying (2 retries left) LBA=398297097
ad8: TIMEOUT - READ_DMA retrying (1 retry left) LBA=398297097
ad8: FAILURE - READ_DMA timed out
ar2: ERROR - array broken
ad7: TIMEOUT - READ_DMA retrying (2 retries left) LBA=490234761
ad7: TIMEOUT - READ_DMA retrying (1 retry left) LBA=490234761
ad7: FAILURE - READ_DMA timed out
ar1: ERROR - array broken
ad5: TIMEOUT - READ_DMA retrying (2 retries left) LBA=488397177
ad5: TIMEOUT - READ_DMA retrying (1 retry left) LBA=488397177
ad5: FAILURE - READ_DMA timed out
ar0: ERROR - array broken


/Daniel Eriksson

------=_NextPart_000_0000_01C48EB5.3E33BF60
Content-Type: application/octet-stream;
	name="dmesg.boot"
Content-Transfer-Encoding: quoted-printable
Content-Disposition: attachment;
	filename="dmesg.boot"

Copyright (c) 1992-2004 The FreeBSD Project.=0A=
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994=0A=
	The Regents of the University of California. All rights reserved.=0A=
FreeBSD 6.0-CURRENT #0: Sat Aug 28 16:54:46 CEST 2004=0A=
    daniel@xxx.xxx.xxx:/usr/obj/usr/src/sys/FORTIFY=0A=
Timecounter "i8254" frequency 1193182 Hz quality 0=0A=
CPU: AMD Athlon(TM) XP 2500+ (1999.78-MHz 686-class CPU)=0A=
  Origin =3D "AuthenticAMD"  Id =3D 0x6a0  Stepping =3D 0=0A=
  =
Features=3D0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE=
,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>=0A=
  AMD Features=3D0xc0400000<AMIE,DSP,3DNow!>=0A=
real memory  =3D 1342156800 (1279 MB)=0A=
avail memory =3D 1304903680 (1244 MB)=0A=
ACPI APIC Table: <ASUS   A7V600-X>=0A=
ioapic0: Changing APIC ID to 2=0A=
ioapic0 <Version 0.3> irqs 0-23 on motherboard=0A=
npx0: [FAST]=0A=
npx0: <math processor> on motherboard=0A=
npx0: INT 16 interface=0A=
acpi0: <ASUS A7V600-X> on motherboard=0A=
acpi0: Power Button (fixed)=0A=
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000=0A=
acpi_timer0: <32-bit timer at 3.579545MHz> port 0xe408-0xe40b on acpi0=0A=
cpu0: <ACPI CPU> on acpi0=0A=
acpi_button0: <Power Button> on acpi0=0A=
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0=0A=
pci0: <ACPI PCI bus> on pcib0=0A=
agp0: <VIA 8377 (Apollo KT400/KT400A/KT600) host to PCI bridge> mem =
0xf8000000-0xfbffffff at device 0.0 on pci0=0A=
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0=0A=
pci1: <ACPI PCI bus> on pcib1=0A=
pci1: <display, VGA> at device 0.0 (no driver attached)=0A=
atapci0: <HighPoint HPT374 (channel 0+1) UDMA133 controller> port =
0xb400-0xb4ff,0xb800-0xb803,0xd000-0xd007,0xd400-0xd403,0xd800-0xd807 =
irq 16 at device 10.0 on pci0=0A=
ata2: channel #0 on atapci0=0A=
ata3: channel #1 on atapci0=0A=
atapci1: <HighPoint HPT374 (channel 2+3) UDMA133 controller> port =
0x9800-0x98ff,0xa000-0xa003,0xa400-0xa407,0xa800-0xa803,0xb000-0xb007 =
irq 16 at device 10.1 on pci0=0A=
ata4: channel #0 on atapci1=0A=
ata5: channel #1 on atapci1=0A=
atapci2: <Promise PDC20318 SATA150 controller> port =
0x8800-0x887f,0x9000-0x900f,0x9400-0x943f mem =
0xed000000-0xed01ffff,0xed800000-0xed800fff irq 19 at device 11.0 on pci0=0A=
atapci2: failed: rid 0x20 is memory, requested 4=0A=
ata6: channel #0 on atapci2=0A=
ata7: channel #1 on atapci2=0A=
ata8: channel #2 on atapci2=0A=
ata9: channel #3 on atapci2=0A=
ahc0: <Adaptec 29160 Ultra160 SCSI adapter> port 0x8400-0x84ff mem =
0xec800000-0xec800fff irq 19 at device 12.0 on pci0=0A=
ahc0: [GIANT-LOCKED]=0A=
aic7892: Ultra160 Wide Channel A, SCSI Id=3D7, 32/253 SCBs=0A=
atapci3: <HighPoint HPT374 (channel 0+1) UDMA133 controller> port =
0x6800-0x68ff,0x7000-0x7003,0x7400-0x7407,0x7800-0x7803,0x8000-0x8007 =
irq 16 at device 13.0 on pci0=0A=
ata10: channel #0 on atapci3=0A=
ata11: channel #1 on atapci3=0A=
atapci4: <HighPoint HPT374 (channel 2+3) UDMA133 controller> port =
0x5000-0x50ff,0x5400-0x5403,0x5800-0x5807,0x6000-0x6003,0x6400-0x6407 =
irq 16 at device 13.1 on pci0=0A=
ata12: channel #0 on atapci4=0A=
ata13: channel #1 on atapci4=0A=
atapci5: <VIA 6420 SATA150 controller> port =
0x3000-0x30ff,0x3400-0x340f,0x3800-0x3803,0x4000-0x4007,0x4400-0x4403,0x4=
800-0x4807 irq 20 at device 15.0 on pci0=0A=
ata14: channel #0 on atapci5=0A=
ata15: channel #1 on atapci5=0A=
atapci6: <VIA 8237 UDMA133 controller> port =
0x2800-0x280f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 irq 20 at device 15.1 =
on pci0=0A=
ata0: channel #0 on atapci6=0A=
ata1: channel #1 on atapci6=0A=
isab0: <PCI-ISA bridge> at device 17.0 on pci0=0A=
isa0: <ISA bus> on isab0=0A=
vr0: <VIA VT6102 Rhine II 10/100BaseTX> port 0x1000-0x10ff mem =
0xeb800000-0xeb8000ff irq 23 at device 18.0 on pci0=0A=
miibus0: <MII bus> on vr0=0A=
rlphy0: <RTL8201L 10/100 media interface> on miibus0=0A=
rlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto=0A=
vr0: Ethernet address: 00:0e:a6:1f:29:1e=0A=
vr0: [GIANT-LOCKED]=0A=
re0: <RealTek 8110S Single-chip Gigabit Ethernet> port 0x800-0x8ff mem =
0xeb000000-0xeb0000ff irq 18 at device 19.0 on pci0=0A=
miibus1: <MII bus> on re0=0A=
rgephy0: <RTL8169S/8110S media interface> on miibus1=0A=
rgephy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, =
1000baseTX-FDX, auto=0A=
re0: Ethernet address: 00:50:fc:f8:c6:81=0A=
re0: [GIANT-LOCKED]=0A=
speaker0 port 0x61 on acpi0=0A=
fdc0: <floppy drive controller> port 0x3f7,0x3f2-0x3f5 irq 6 drq 2 on =
acpi0=0A=
fd0: <1440-KB 3.5" drive> on fdc0 drive 0=0A=
sio0: configured irq 4 not in bitmap of probed irqs 0=0A=
sio0: port may not be enabled=0A=
sio0 port 0x3f8-0x3ff irq 4 on acpi0=0A=
sio0: type 16550A, console=0A=
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0=0A=
atkbd0: <AT Keyboard> irq 1 on atkbdc0=0A=
kbd0 at atkbd0=0A=
atkbd0: [GIANT-LOCKED]=0A=
orm0: <ISA Option ROM> at iomem 0xc0000-0xcafff on isa0=0A=
pmtimer0 on isa0=0A=
ppc0: parallel port not found.=0A=
sc0: <System console> at flags 0x100 on isa0=0A=
sc0: VGA <16 virtual consoles, flags=3D0x100>=0A=
sio1: configured irq 3 not in bitmap of probed irqs 0=0A=
sio1: port may not be enabled=0A=
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0=0A=
Timecounter "TSC" frequency 1999783189 Hz quality 800=0A=
Timecounters tick every 1.000 msec=0A=
ipfw2 initialized, divert enabled, rule-based forwarding disabled, =
default to accept, logging unlimited=0A=
ad0: 114473MB <ST3120022A/3.06> [232581/16/63] at ata0-master UDMA100=0A=
ad1: 114473MB <ST3120022A/3.06> [232581/16/63] at ata0-slave UDMA100=0A=
ad2: 117800MB <IC35L120AVV207-0/V24OA66A> [239340/16/63] at ata1-master =
UDMA100=0A=
ad3: 117800MB <IC35L120AVV207-0/V24OA66A> [239340/16/63] at ata1-slave =
UDMA100=0A=
ad4: 238475MB <WDC WD2500JB-00FUA0/15.05R15> [484521/16/63] at =
ata2-master UDMA100=0A=
ad5: 238475MB <WDC WD2500JB-00FUA0/15.05R15> [484521/16/63] at =
ata2-slave UDMA100=0A=
ad6: 239372MB <Maxtor 4A250J0/RAMB1TU0> [486344/16/63] at ata3-master =
UDMA133=0A=
ad7: 239372MB <Maxtor 5A250J0/RAMB1TV0> [486344/16/63] at ata3-slave =
UDMA133=0A=
ad8: 194481MB <Maxtor 6Y200P0/YAR41BW0> [395136/16/63] at ata4-master =
UDMA133=0A=
ad9: 194481MB <Maxtor 6Y200P0/YAR41VW0> [395136/16/63] at ata4-slave =
UDMA133=0A=
ad10: 194481MB <Maxtor 6Y200P0/YAR41BW0> [395136/16/63] at ata5-master =
UDMA133=0A=
ad11: 239372MB <Maxtor 7Y250P0/YAR41BW0> [486344/16/63] at ata5-slave =
UDMA133=0A=
ad12: 239372MB <Maxtor 7Y250M0/YAR51EW0> [486344/16/63] at ata6-master =
SATA150=0A=
ad14: 238475MB <WDC WD2500JD-00FYB0/02.05D02> [484521/16/63] at =
ata7-master SATA150=0A=
ad20: 117800MB <IC35L120AVV207-0/V24OA66A> [239340/16/63] at =
ata10-master UDMA100=0A=
ad21: 117800MB <HDS722512VLAT20/V33OA60A> [239340/16/63] at ata10-slave =
UDMA100=0A=
ad22: 117246MB <Maxtor 6Y120L0/YAR41BW0> [238216/16/63] at ata11-master =
UDMA133=0A=
ad23: 117246MB <Maxtor 6Y120L0/YAR41BW0> [238216/16/63] at ata11-slave =
UDMA133=0A=
ad24: 114473MB <WDC WD1200JB-00DUA3/75.13B75> [232581/16/63] at =
ata12-master UDMA100=0A=
ad25: 117800MB <IC35L120AVV207-1/V24OA66A> [239340/16/63] at ata12-slave =
UDMA100=0A=
ad26: 26059MB <Maxtor 92732U8/RA530JN0> [52946/16/63] at ata13-master =
UDMA66=0A=
ar0: 476950MB <ATA RAID0 array> [60802/255/63] status: READY subdisks:=0A=
 disk0 READY on ad4 at ata2-master=0A=
 disk1 READY on ad5 at ata2-slave=0A=
ar1: 478744MB <ATA RAID0 array> [61031/255/63] status: READY subdisks:=0A=
 disk0 READY on ad6 at ata3-master=0A=
 disk1 READY on ad7 at ata3-slave=0A=
ar2: 388962MB <ATA RAID0 array> [49585/255/63] status: READY subdisks:=0A=
 disk0 READY on ad9 at ata4-slave=0A=
 disk1 READY on ad8 at ata4-master=0A=
ar3: 228946MB <ATA RAID0 array> [29186/255/63] status: READY subdisks:=0A=
 disk0 READY on ad23 at ata11-slave=0A=
 disk1 READY on ad24 at ata12-master=0A=
Waiting 5 seconds for SCSI devices to settle=0A=
sa0 at ahc0 bus 0 target 5 lun 0=0A=
sa0: <Seagate STT20000N 6A51> Removable Sequential Access SCSI-2 device =0A=
sa0: 10.000MB/s transfers (10.000MHz, offset 15)=0A=
da0 at ahc0 bus 0 target 10 lun 0=0A=
da0: <IBM DDYS-T36950N S93E> Fixed Direct Access SCSI-3 device =0A=
da0: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged =
Queueing Enabled=0A=
da0: 35003MB (71687340 512 byte sectors: 255H 63S/T 4462C)=0A=
da1 at ahc0 bus 0 target 11 lun 0=0A=
da1: <IBM IC35L036UWD210-0 S5CQ> Fixed Direct Access SCSI-3 device =0A=
da1: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged =
Queueing Enabled=0A=
da1: 35003MB (71687340 512 byte sectors: 255H 63S/T 4462C)=0A=
da2 at ahc0 bus 0 target 12 lun 0=0A=
da2: <IBM DDYS-T36950N S93E> Fixed Direct Access SCSI-3 device =0A=
da2: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged =
Queueing Enabled=0A=
da2: 35003MB (71687340 512 byte sectors: 255H 63S/T 4462C)=0A=
da3 at ahc0 bus 0 target 13 lun 0=0A=
da3: <IBM DDYS-T36950N S93E> Fixed Direct Access SCSI-3 device =0A=
da3: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged =
Queueing Enabled=0A=
da3: 35003MB (71687340 512 byte sectors: 255H 63S/T 4462C)=0A=
Mounting root from ufs:/dev/ad0s1a=0A=
=0A=

------=_NextPart_000_0000_01C48EB5.3E33BF60--




Want to link to this message? Use this URL: <http://docs.FreeBSD.org/cgi/mid.cgi?!~!UENERkVCMDkAAQACAAAAAAAAAAAAAAAAABgAAAAAAAAA0VcX9IoJqUaXPS8MjT1PdsKAAAAQAAAAKptuZr9dAUWKvmgdFpGa0wEAAAAA>