Date: Thu, 20 Oct 2005 12:31:59 +0000 From: Marcin Jessa <lists@yazzy.org> To: Marcin Jessa <lists@yazzy.org> Cc: glebius@FreeBSD.org, current@FreeBSD.org, net@FreeBSD.org Subject: Re: PPPoE and Radius on 6.0RC1 Message-ID: <20051020123159.33f6fa33.lists@yazzy.org> In-Reply-To: <20051020131549.5e432073.lists@yazzy.org> References: <20051019235111.2225345e.lists@yazzy.org> <20051020070145.GA59364@cell.sick.ru> <20051020131549.5e432073.lists@yazzy.org>
next in thread | previous in thread | raw e-mail | index | archive | help
On Thu, 20 Oct 2005 13:15:49 +0200 Marcin Jessa <lists@yazzy.org> wrote: > On Thu, 20 Oct 2005 11:01:45 +0400 > Gleb Smirnoff <glebius@FreeBSD.org> wrote: > > > On Wed, Oct 19, 2005 at 11:51:11PM +0200, Marcin Jessa wrote: > > M> It seems like PPPoE stoped working with support for radius on 6.0 > > M> The log of pppoe and freeradius does not show pppoe attempting to > > M> even talk to the radius server. Additionally this message pops up > > M> when enabling pppoed: WARNING: attempt to net_add_domain > > M> (netgraph) after domainfinalize() My setup worked fine before on > > M> FreeBSD 5.x Is that a known issue and is it being worked on? > > > > Please show your PPPoE server configuration. Do you use pppoed or > > mpd? > > I use pppoed. > Adding > netgraph_load="YES" > ng_socket_load="YES" > to /boot/loader.conf fixed it on my 6.0RC1 ( thanks Julian Elischer ) > Frankly I don't understand why this is needed since pppoed loads those > modules when it starts up. Just tested the same setup on 7.0 built tonight and it did not work. The pppoed daemon never sends any requests to freeradius... I tried to additionaly with those modules listed in loader.conf with no luck: ng_ether_load="YES" ng_pppoe_load="YES" > This is my ppp.conf, just for the record: > > default: > #set log Chat Command Phase #turn on some logging. See man > ppp.conf for info set log Chat Command Phase hdlc lqm ipcp > enable mschapv2 mschap chap mppe #turn on chap and pap > accounting > #enable pap mschapv2 mschap chap mppe #turn on chap and pap > #accounting enable pap #turn on chap and pap > #accounting > allow mode direct #turn on ppp bridging > enable proxy #turn on ppp proxyarping (redundant of > above???) disable ipv6cp #we don't use ipv6, don't > want the errors set mru 1472 #set mru below 1500 > (PPPoE MTU issue) set mtu 1472 #set mtu below 1500 > (PPPoE MTU issue) set timeout 0 #no mins time > restriction on users #set timeout never > set mppe 128 * > set ifaddr 192.168.2.8 192.168.2.100-192.168.1.120 255.255.255.255 > set log phase ipcp lcp debug #additional debugging > nat enable yes > set dns 192.168.2.45 192.168.2.8 > #set speed sync > set cd 3 # checks for the existence of carrier > once per second for 5 seconds #set cd 5! > #enable echo > enable lqr > set reconnect 1 5 # Should the line drop unexpectedly , > a connection will be re-established after the given timeout. > > #Specify my wifi gateway IP as well as DHCP pool range > set radius /etc/ppp/radius.conf #turn on radius auth and use > this file accept dns #turn on dns > cacheing/forwarding > > #enable pap mschapv2 mschap chap mppe #turn on chap and pap > #accounting > disable pap pred1 deflate #disable pred1 and deflate > compression along with pap deny pap pred1 deflate > #refuse when ask for it > _______________________________________________ > freebsd-current@freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-current > To unsubscribe, send any mail to > "freebsd-current-unsubscribe@freebsd.org"
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20051020123159.33f6fa33.lists>