Date: Wed, 9 Aug 2000 10:19:12 -0400 (EDT) From: Paul LaFollette <lafollet@andante.cis.temple.edu> To: freebsd-questions@FreeBSD.ORG Subject: /dev/card0 not configured Message-ID: <200008091419.KAA19993@andante.cis.temple.edu>
next in thread | raw e-mail | index | archive | help
Good and helpful people,
I am running 4.0 (from the CD-rom distribution) on an IBM i1400
series thinkpad type 2611-451. I have a Viking pcmcia Modem card
(WHY do thay have to use stupid winmodems as the built-in's. spit!)
Anyway, I am having problems with getting the system to see the
pccard system. On bootup, when it tries to run pccardc, I get a
message that says that /dev/card0 is not configured.
I have searched both the FreeBSD archive and deja.com and found several
folks with similar problems, but no answers that are helpful. I
apologize if I have missed the very one that I need. Any help I can
get would be most appreciatively received. To the details...
Windoze 98 boots fine without conflict, and the Viking card works there.
BIOS setup shows the serial port to be at 0x3F8 with irq 4, and the
parallel to be at 0x378 with irq 7.
dmesg output and my config file follow.
Is the line that reads "PnP device failed to report resource
data" significant? how?
dmesg output:
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
FreeBSD 4.0-RELEASE #0: Wed Aug 2 23:29:13 EDT 2000
lafollet@:/usr/src/sys/compile/SCHERZO
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium/P55C (quarter-micron) (299.94-MHz 586-class CPU)
Origin = "GenuineIntel" Id = 0x582 Stepping = 2
Features=0x8001bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,MMX>
real memory = 67043328 (65472K bytes)
config> di sn0
No such device: sn0
Invalid command or syntax. Type `?' for help.
config> di lnc0
No such device: lnc0
Invalid command or syntax. Type `?' for help.
config> di le0
No such device: le0
Invalid command or syntax. Type `?' for help.
config> di ie0
No such device: ie0
Invalid command or syntax. Type `?' for help.
config> di fe0
No such device: fe0
Invalid command or syntax. Type `?' for help.
config> di ed0
No such device: ed0
Invalid command or syntax. Type `?' for help.
config> di cs0
No such device: cs0
Invalid command or syntax. Type `?' for help.
config> di bt0
No such device: bt0
Invalid command or syntax. Type `?' for help.
config> di aic0
No such device: aic0
Invalid command or syntax. Type `?' for help.
config> di aha0
No such device: aha0
Invalid command or syntax. Type `?' for help.
config> di adv0
No such device: adv0
Invalid command or syntax. Type `?' for help.
config> en ata0
config> po ata0 0x1f0
config> ir ata0 14
config> f ata0 0
config> q
avail memory = 61820928 (60372K bytes)
Preloaded elf kernel "kernel" at 0xc030f000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc030f09c.
Intel Pentium detected, installing workaround for F00F bug
md0: Malloc disk
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
isab0: <AcerLabs M1533 portable PCI-ISA bridge> at device 2.0 on pci0
isa0: <ISA bus> on isab0
chip1: <PCI to CardBus bridge (vendor=1217 device=6832)> irq 9 at device 5.0 on pci0
chip2: <PCI to CardBus bridge (vendor=1217 device=6832)> irq 9 at device 5.1 on pci0
pci0: <NeoMagic MagicGraph 128XD SVGA controller> at 6.0 irq 9
atapci0: <AcerLabs Aladdin ATA33 controller> port 0x6090-0x609f irq 15 at device 11.0 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
chip3: <AcerLabs M15x3 Power Management Unit> port 0xf140-0xf15f,0xf100-0xf13f at device 12.0 on pci0
ohci0: <AcerLabs M5237 (Aladdin-V) USB controller> mem 0x6300000-0x6300fff irq 10 at device 15.0 on pci0
usb0: OHCI version 1.0, legacy support
usb0: <AcerLabs M5237 (Aladdin-V) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: AcerLabs OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
PnP device failed to report resource data
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <keyboard controller (i8042)> at port 0x60-0x6f on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x200>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: configured irq 3 not in bitmap of probed irqs 0
ppc0: cannot reserve I/O port range
unknown0: <YAMAHA OPL3-SAx Audio System> at port 0x220-0x22f,0x530-0x537,0x388-0x38f,0x330-0x331,0x370-0x371 irq 5 drq 0,7 on isa0
ad0: 4126MB <IBM-DKLA-24320> [8944/15/63] at ata0-master using UDMA33
acd0: CDROM <CRN-8241B> at ata1-master using PIO4
Mounting root from ufs:/dev/ad0s2a
Config file:
#
# GENERIC -- Generic kernel configuration file for FreeBSD/i386
#
# For more information on this file, please read the handbook section on
# Kernel Configuration Files:
#
# http://www.freebsd.org/handbook/kernelconfig-config.html
#
# The handbook is also available locally in /usr/share/doc/handbook
# if you've installed the doc distribution, otherwise always see the
# FreeBSD World Wide Web server (http://www.FreeBSD.ORG/) for the
# latest information.
#
# An exhaustive list of options and more detailed explanations of the
# device lines is also present in the ./LINT configuration file. If you are
# in doubt as to the purpose or necessity of a line, check first in LINT.
#
# $FreeBSD: src/sys/i386/conf/SCHERZO,v 1.246 2000/03/09 16:32:55 jlemon Exp $
machine i386
cpu I586_CPU
cpu I686_CPU
ident SCHERZO
maxusers 32
#makeoptions DEBUG=-g #Build kernel with gdb(1) debug symbols
options MATH_EMULATE #Support for x87 emulation
options INET #InterNETworking
options INET6 #IPv6 communications protocols
options FFS #Berkeley Fast Filesystem
options FFS_ROOT #FFS usable as root device [keep this!]
options MFS #Memory Filesystem
options MD_ROOT #MD is a potential root device
options NFS #Network Filesystem
options NFS_ROOT #NFS usable as root device, NFS required
options MSDOSFS #MSDOS Filesystem
options CD9660 #ISO 9660 Filesystem
options CD9660_ROOT #CD-ROM usable as root, CD9660 required
options PROCFS #Process filesystem
options COMPAT_43 #Compatible with BSD 4.3 [KEEP THIS!]
options SCSI_DELAY=15000 #Delay (in ms) before probing SCSI
options UCONSOLE #Allow users to grab the console
options USERCONFIG #boot -c editor
options VISUAL_USERCONFIG #visual boot -c editor
options KTRACE #ktrace(1) support
options SYSVSHM #SYSV-style shared memory
options SYSVMSG #SYSV-style message queues
options SYSVSEM #SYSV-style semaphores
options P1003_1B #Posix P1003_1B real-time extentions
options _KPOSIX_PRIORITY_SCHEDULING
options ICMP_BANDLIM #Rate limit bad replies
# To make an SMP kernel, the next two are needed
#options SMP # Symmetric MultiProcessor Kernel
#options APIC_IO # Symmetric (APIC) I/O
# Optionally these may need tweaked, (defaults shown):
#options NCPU=2 # number of CPUs
#options NBUS=4 # number of busses
#options NAPIC=1 # number of IO APICs
#options NINTR=24 # number of INTs
device isa
device eisa
device pci
# Floppy drives
device fdc0 at isa? port IO_FD1 irq 6 drq 2
device fd0 at fdc0 drive 0
#device fd1 at fdc0 drive 1
# ATA and ATAPI devices
device ata0 at isa? port IO_WD1 irq 14
device ata1 at isa? port IO_WD2 irq 15
device ata
device atadisk # ATA disk drives
device atapicd # ATAPI CDROM drives
#device atapifd # ATAPI floppy drives
#device atapist # ATAPI tape drives
options ATA_STATIC_ID #Static device numbering
#options ATA_ENABLE_ATAPI_DMA #Enable DMA on ATAPI devices
# SCSI Controllers
#device ahb # EISA AHA1742 family
#device ahc # AHA2940 and onboard AIC7xxx devices
#device amd # AMD 53C974 (Teckram DC-390(T))
#device dpt # DPT Smartcache - See LINT for options!
#device isp # Qlogic family
#device ncr # NCR/Symbios Logic
#device sym # NCR/Symbios Logic (newer chipsets)
#device adv0 at isa?
#device adw
#device bt0 at isa?
#device aha0 at isa?
#device aic0 at isa?
# SCSI peripherals
device scbus # SCSI bus (required)
#device da # Direct Access (disks)
#device sa # Sequential Access (tape etc)
#device cd # CD
device pass # Passthrough device (direct SCSI access)
# RAID controllers
#device ida # Compaq Smart RAID
#device amr # AMI MegaRAID
#device mlx # Mylex DAC960 family
# atkbdc0 controls both the keyboard and the PS/2 mouse
device atkbdc0 at isa? port IO_KBD
device atkbd0 at atkbdc? irq 1
device psm0 at atkbdc? irq 12
device vga0 at isa?
# splash screen/screen saver
pseudo-device splash
# syscons is the default console driver, resembling an SCO console
device sc0 at isa?
# Enable this and PCVT_FREEBSD for pcvt vt220 compatible console driver
#device vt0 at isa?
#options XSERVER # support for X server on a vt console
#options FAT_CURSOR # start with block cursor
# If you have a ThinkPAD, uncomment this along with the rest of the PCVT lines
#options PCVT_SCANSET=2 # IBM keyboards are non-std
# Floating point support - do not disable.
device npx0 at nexus? port IO_NPX irq 13
# Power management support (see LINT for more options)
device apm0 at nexus? disable flags 0x20 # Advanced Power Management
# PCCARD (PCMCIA) support
device card
device pcic0 at isa? irq 10 port 0x3e0 iomem 0xd0000
device pcic1 at isa? irq 11 port 0x3e2 iomem 0xd4000 disable
# Serial (COM) ports
device sio0 at isa? port IO_COM1 flags 0x10 irq 4
device sio1 at isa? port IO_COM2 irq 3
#device sio2 at isa? disable port IO_COM3 irq 5
#device sio3 at isa? disable port IO_COM4 irq 9
# Parallel port
device ppc0 at isa? irq 7
device ppbus # Parallel port bus (required)
device lpt # Printer
device plip # TCP/IP over parallel
device ppi # Parallel port interface device
#device vpo # Requires scbus and da
# PCI Ethernet NICs.
#device de # DEC/Intel DC21x4x (``Tulip'')
#device fxp # Intel EtherExpress PRO/100B (82557, 82558)
#device tx # SMC 9432TX (83c170 ``EPIC'')
#device vx # 3Com 3c590, 3c595 (``Vortex'')
#device wx # Intel Gigabit Ethernet Card (``Wiseman'')
# PCI Ethernet NICs that use the common MII bus controller code.
#device miibus # MII bus support
#device dc # DEC/Intel 21143 and various workalikes
#device rl # RealTek 8129/8139
#device sf # Adaptec AIC-6915 (``Starfire'')
#device sis # Silicon Integrated Systems SiS 900/SiS 7016
#device ste # Sundance ST201 (D-Link DFE-550TX)
#device tl # Texas Instruments ThunderLAN
#device vr # VIA Rhine, Rhine II
#device wb # Winbond W89C840F
#device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'')
# ISA Ethernet NICs.
#device ed0 at isa? port 0x280 irq 10 iomem 0xd8000
#device ex
#device ep
# WaveLAN/IEEE 802.11 wireless NICs. Note: the WaveLAN/IEEE really
# exists only as a PCMCIA device, so there is no ISA attatement needed
# and resources will always be dynamically assigned by the pccard code.
#device wi
# Aironet 4500/4800 802.11 wireless NICs. Note: the declaration below will
# work for PCMCIA and PCI cards, as well as ISA cards set to ISA PnP
# mode (the factory default). If you set the switches on your ISA
# card for a manually chosen I/O address and IRQ, you must specify
# those paremeters here.
#device an
# The probe order of these is presently determined by i386/isa/isa_compat.c.
#device ie0 at isa? port 0x300 irq 10 iomem 0xd0000
#device fe0 at isa? port 0x300
#device le0 at isa? port 0x300 irq 5 iomem 0xd0000
#device lnc0 at isa? port 0x280 irq 10 drq 0
#device cs0 at isa? port 0x300
#device sn0 at isa? port 0x300 irq 10
# requires PCCARD (PCMCIA) support to be activated
#device xe0 at isa?
# Pseudo devices - the number indicates how many units to allocated.
pseudo-device loop # Network loopback
pseudo-device ether # Ethernet support
pseudo-device sl 1 # Kernel SLIP
pseudo-device ppp 1 # Kernel PPP
pseudo-device tun # Packet tunnel.
pseudo-device pty # Pseudo-ttys (telnet etc)
pseudo-device md # Memory "disks"
pseudo-device gif 4 # IPv6 and IPv4 tunneling
pseudo-device faith 1 # IPv6-to-IPv4 relaying (translation)
# The `bpf' pseudo-device enables the Berkeley Packet Filter.
# Be aware of the administrative consequences of enabling this!
pseudo-device bpf #Berkeley packet filter
# USB support
device uhci # UHCI PCI->USB interface
device ohci # OHCI PCI->USB interface
device usb # USB Bus (required)
device ugen # Generic
#device uhid # "Human Interface Devices"
#device ukbd # Keyboard
#device ulpt # Printer
#device umass # Disks/Mass storage - Requires scbus and da
#device ums # Mouse
# USB Ethernet, requires mii
#device aue # ADMtek USB ethernet
#device cue # CATC USB ethernet
#device kue # Kawasaki LSI USB ethernet
Again, thank you for any help you might be able to give.
Paul
Paul LaFollette
Assoc. Prof.
CIS Dept.
Temple University
Philadelphia, PA 19119 USA
+1 215 204 6822
lafollet@andante.cis.temple.edu
lafollet@netaxs.com
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200008091419.KAA19993>