Date: Sat, 27 Apr 1996 23:39:36 -0400 (EDT) From: Robert Nicholson <robert@elastica.com> To: flexfax@celestial.com Cc: questions@freebsd.org Subject: Anybody using a Zyxel Elite 2864? (Can not deduce modem type) Message-ID: <199604280339.XAA00449@justine.elastica.com>
next in thread | raw e-mail | index | archive | help
My elite is using the latest ROM revision... (dated March 96 I think). My log is showing the following when I attempt to send a fax justine% faxstat Server on localhost:FIFO for all modems: Running. Job Modem Destination Time-To-Send Sender Status 1 any +17039180498 23:22 1996/04/27 Robert Nichols Queued and waiting justine% Apr 27 23:22:29 justine FaxQueuer[191]: SUBMIT JOB "sendq/q1" Apr 27 23:22:37 justine FaxSend[353]: /dev/cuaa1: Can not deduce modem type. My modem config file is as follows # $Header: /usr/people/sam/fax/./config/RCS/zyxel-1496e-2.0,v 1.14 1995/04/08 21:25:03 sam Rel $ # # HylaFAX Facsimile Software # # Copyright (c) 1990-1995 Sam Leffler # Copyright (c) 1991-1995 Silicon Graphics, Inc. # HylaFAX is a trademark of Silicon Graphics, Inc. # # Permission to use, copy, modify, distribute, and sell this software and # its documentation for any purpose is hereby granted without fee, provided # that (i) the above copyright notices and this permission notice appear in # all copies of the software and related documentation, and (ii) the names of # Sam Leffler and Silicon Graphics may not be used in any advertising or # publicity relating to the software without the specific, prior written # permission of Sam Leffler and Silicon Graphics. # # THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND, # EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY # WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. # # IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR # ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND, # OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, # WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF # LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE # OF THIS SOFTWARE. # # # Configuration for a ZyXEL-1496E w/ Class 2.0 firmware. # Firmware revisions from 6.12 on should work. # # This configuration file sets up the ZyXEL to run at 38.4 for # both sending and receiving. RTS/CTS flow control is used on # the tty port--you probably shouldn't use XON/XOFF. Note that # on an SGI system the getty speed is the following non-standard # gettydefs entry: # # dx_38400# B38400 # B38400 SANE TAB3 HUPCL #\r\n\n$HOSTNAME login: #dx_38400 # # CountryCode: 1 AreaCode: 703 FAXNumber: +1.703.560.4121 LongDistancePrefix: 1 InternationalPrefix: 011 DialStringRules: etc/dialrules ServerTracing: 1 SessionTracing: 11 RecvFileMode: 00600 LogFileMode: 00600 DeviceMode: 00600 RingsBeforeAnswer: 1 SpeakerVolume: off GettyArgs: "-h %l dx_%s" LocalIdentifier: +17035604121 TagLineFont: etc/lutRS18.pcf TagLineFormat: "From %%l|%c|Page %%p of %%t" NoCarrierRetrys: 3 MaxRecvPages: 25 # # # Modem-related stuff: should reflect modem command interface # and hardware connection/cabling (e.g. flow control). # ModemType: Class2.0 # use class 2.0 interface ModemRate: 38400 # 38.4 works fine ModemFlowControl: rtscts # default # ModemNoFlowCmd: AT&H0 # disable flow control ModemHardFlowCmd: AT&H3 # hardware flow control ModemSoftFlowCmd: AT&H4 # software flow control ModemSetupDTRCmd: AT&D2 # DTR off causes modem to hang up ModemSetupDCDCmd: AT&C1 # DCD tracks carrier # ModemSetupAACmd: AT+FAA=1 # enable in current class # # Additional reset commands: # # &B1 DTE-DCE rate is fixed at DTE setting # &N0 Auto-negotiate highest possible DCE-DCE link rate # &S0 DSR always on # *F0 Deny remote configuration # S18=2 Receive at 38400 # S38.3=1 DCD on/off sequence follows UNIX standard; also # fix receiving baud rate at S18 value # S39=0 (avoid Class 2 compatibility hacks) # ModemResetCmds: AT&B1&N0&S0*F0S18=2S38.3=1S39=0 # ModemDialCmd: ATDT%s # no '@' 'cuz then busy not recognized NoCarrierRetrys: 3 # retry 3 times on no carrier # ModemSetVolumeCmd: "ATM0 ATM1L1 ATM1L3 ATM1L5 ATM1L7" # # Caller ID configuration setup. # #QualifyCID: etc/cid # CID access control list file #CIDNumber: "CALLER NUMBER: " # pattern string for phone number info #CIDName: "CALLER NAME: " # pattern string for identity info # PagerSetupCmds: AT&K0&N15 # use V.22 at 1200 bps (PageNet) ------------------------------------------------------------------------------- Here's my general config file.. LogFacility: daemon CountryCode: 1 AreaCode: 703 LongDistancePrefix: 1 InternationalPrefix: 011 DialStringRules: etc/dialrules ServerTracing: 1 ------------------------------------------------------------------------------- Anybody know why it's complaining? Also, when I faxrm the job I get back a message but it says that "No transcript is available" How can I log the session to the modem so I can diagnose the problem?
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?199604280339.XAA00449>