Date: Wed, 10 Feb 1999 10:32:34 -0800 From: "RTI- Alexey Katz" <alexeyk@retailpro.com> To: freebsd-questions@FreeBSD.ORG Subject: kernel compiling Message-ID: <36C1D0C2.A33A7116@retailpro.com>
next in thread | raw e-mail | index | archive | help
Hi there, I just installed FreeBSD 3.0-RELEASE and tried to recompile kernel. First of all I installed all sources from CDROM (CD number 1 from 4-disks pack). Then I created custom configuration file naed GREENWITCH where I turned on ncr0 driver. Then I tried to start "config GREENWITCH" - it worked. Then I switched to compile/GREENWITCH directory and issued "make depend". After some time it reported that file scsi/scsiconf.h referenced in pci/tek390.c can't be found. After examination I've found that files scsi/scsi*.h referenced in the following files alpha/tc/esp.c:#include <scsi/scsi_all.h> alpha/tc/esp.c:#include <scsi/scsiconf.h> ^^^^^^^^ (this one is referenced if compiling for NetBSD, but not for FreeBSD) alpha/tc/esp.c:#include <scsi/scsi_message.h> alpha/tc/tcds_dma.c:#include <scsi/scsi_all.h> alpha/tc/tcds_dma.c:#include <scsi/scsiconf.h> dev/dpt/dpt_control.c:#include <scsi/scsiconf.h> dev/isp/isp_freebsd.h:#include <scsi/scsiconf.h> i386/isa/aic6360.c:#include <scsi/scsiconf.h> i386/isa/aic6360.c:#include <scsi/scsi_debug.h> i386/isa/bs/bsif.h:#include <scsi/scsi_all.h> i386/isa/bs/bsif.h:#include <scsi/scsiconf.h> i386/isa/bs/bsif.h:#include <scsi/scsi_disk.h> i386/isa/bs/bsif.h:#include <scsi/scsi_all.h> i386/isa/bs/bsif.h:#include <scsi/scsiconf.h> i386/isa/bs/bsif.h:#include <scsi/scsi_disk.h> i386/isa/ncr5380.c:#include <scsi/scsiconf.h> i386/isa/seagate.c:#include <scsi/scsiconf.h> i386/isa/ultra14f.c:#include <scsi/scsiconf.h> i386/isa/ultra14f.c:#include <scsi/scsi_debug.h> i386/isa/wd7000.c:#include <scsi/scsiconf.h> pci/tek390.c:#include <scsi/scsiconf.h> ^^^^^^^^^^ (this one uses .h file in all configuration) can't be found simply because directory /usr/src/sys/scsi/ is missing. I've copied them from my old 2.2.7 system and finally was able to finish "make depend". But I can't compile - there're some undefined symbols in pci/tek390.c. I know that ncr driver is not supported by CAM and should use old SCSI subsystem but I can't find it. I've looked to ftp://ftp.freebsd.org to /pub/FreeBSD/3.0-STABLE/src/sys/ but there is no scsi/*.h files. There are cam/scsi/*.h files but the file scsiconf.h is not there, so I assume that it's not what I'm looking for. Can you give me any advise where to look? -- Bye Alexey Kats alexeyk@retailpro.com To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?36C1D0C2.A33A7116>