Date: Fri, 29 Mar 2002 18:22:59 -0500 (EST) From: "Adam D. Gorski" <agorski@engin.umich.edu> To: <bdodson@scms.utmb.edu> Cc: <freebsd-multimedia@FreeBSD.ORG> Subject: Re: SB problem (was: Cat'ing /dev/audio) Message-ID: <Pine.SOL.4.33.0203291821030.10192-100000@and.engin.umich.edu> In-Reply-To: <200203292315.g2TNFmA97325@scms.utmb.edu>
next in thread | previous in thread | raw e-mail | index | archive | help
No, I still have the problem. I moved the card around, but that didn't help anything. I even took out the (possibly offending) RTL card, but that had no effect either. I'm at a loss really... I guess I don't _need_ mp3's, but this is one of those problems that just nags at the back of your brain... - Adam On Fri, 29 Mar 2002 bdodson@scms.utmb.edu wrote: ::Or moving the card to a different slot? :: ::But, from your posting to the list, it seems you don't have a problem ::any more, is that right? :: ::You guys have saturated my knowledge base :( ::Sorry :: ::Bud :: ::On 29 Mar, John Utz wrote: ::> that's an interesting result ::> ::> have you tried hardwiring the irq's in the bios? ::> ::> ::> On Fri, 29 Mar 2002, Adam D. Gorski wrote: ::> ::>> Ok.. I compared dmesg versus pciconf -l, and I found this.. I dunno if this ::>> means anything, but I figured I'd mention it... the first matching works, ::>> which is for my 3Com card: ::>> ::>> * dmesg: ::>> xl0: <3Com 3c900B-TPO Etherlink XL> port 0xd000-0xd07f mem ::>> 0xe1000000-0xe100007f irq 9 at device 9.0 on pci0 ::>> ::>> * pciconf -l ::>> xl0@pci0:9:0: class=0x020000 card=0x900410b7 chip=0x900410b7 rev=0x04 ::>> hdr=0x00 ::>> ::>> So both show IRQ 9 (if I'm reading the output right) which seems fine.. ::>> but.. check out my RTL and SB outputs: ::>> ::>> * dmesg ::>> rl0: <RealTek 8139 10/100BaseTX> port 0x9800-0x98ff mem ::>> 0xe0000000-0xe00000ff irq 11 at device 12.0 on pci0 ::>> ::>> pcm0: <Creative CT5880-C> port 0xa000-0xa03f irq 10 at device 11.0 on pci0 ::>> ::>> * pciconf -l ::>> rl0@pci0:12:0: class=0x020000 card=0x813910ec chip=0x813910ec rev=0x10 ::>> hdr=0x00 ::>> ::>> pcm0@pci0:11:0: class=0x040100 card=0x20001274 chip=0x58801274 rev=0x02 ::>> hdr=0x00 ::>> ::>> ::>> Ok, notice how one lists the SB @ IRQ 10, while the other shows it @ IRQ 11? ::>> I dunno, just something that caught my eye based on the suggestions below. ::>> ::>> Maybe this helps, ::>> ::>> - Adam ::>> ::>> ::>> On Fri, 29 Mar 2002 bdodson@scms.utmb.edu wrote: ::>> ::>> ::On 29 Mar, Adam D. Gorski wrote: ::>> ::> Hey, ::>> ::> ::>> ::> Thanks for the response. I went into my BIOS and told it that I don't have a ::>> ::> PnP OS, but the modules still did not detect the card. So I re-compiled the ::>> ::> kernel with 'device pcm', and the card is detected once again, but the ::>> ::> problems persist. I'm going to try some things that were suggested still, ::>> ::> and hopefully I'll get at least a step closer to the solution. Thanks once ::>> ::> again! ::>> ::> ::>> ::> - Adam ::>> ::> ::>> :: ::>> ::Hmm... I'm out of ideas. The bare 'device pcm' is right for devices ::>> ::being configured by pnp (as all pci devices are). 'device pcm0 ......' ::>> ::is right for devices which need to be hand configured (only isa or ::>> ::pccard devices). It sounds to me like you may have pci irq (or other ::>> ::resource) conflicts. You might try to do ::>> :: ::>> ::pciconf -vl (as root) ::>> :: ::>> ::and see if anything shows up that looks obviously bogus. I'm sorry I ::>> ::can't help you with the interpretation, but if you post the result to ::>> ::the multimedia list, this may allow them to give you better help. ::>> :: ::>> ::Good luck, ::>> ::Bud ::>> :: ::>> ::> On Fri, 29 Mar 2002 bdodson@scms.utmb.edu wrote: ::>> ::> ::>> ::> ::(reading your post via the archives, not subscribed to multimedia) ::>> ::> :: ::>> ::> ::I'm sure that someone will point out that FreeBSD is NOT a "PnP OS", so ::>> ::> ::you need to set your BIOS to "PnP OS = NO". I have no idea whether that ::>> ::> ::will fix your problem, but I know for sure setting it to YES is wrong. ::>> ::> ::That is probably why the modules did not work right: nothing is ::>> ::> ::configuring PNP. ::>> ::> :: ::>> ::> ::Good luck, ::>> ::> ::Bud Dodson ::>> ::> :: ::>> :: ::>> :: :: ::-- ::M. L. Dodson bdodson@scms.utmb.edu ::409-772-2178 FAX: 409-772-1790 :: :: ::To Unsubscribe: send mail to majordomo@FreeBSD.org ::with "unsubscribe freebsd-multimedia" in the body of the message :: To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-multimedia" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.SOL.4.33.0203291821030.10192-100000>