Skip site navigation (1)Skip section navigation (2)
Date:      Thu, 31 Oct 2002 13:15:20 -0800 (PST)
From:      Pete Carah <pete@ns.altadena.net>
To:        current@freebsd.org
Subject:   Boot-time hang after init, still (VAIO R505ES again)
Message-ID:  <200210312115.g9VLFKkK038452@ns.altadena.net>

next in thread | raw e-mail | index | archive | help
CVSUP as of last night about 10PM PST:

Well, phk's stuff now appears to work right (even finds the memory stick
most of the time) and the bad malloc in acpi is fixed.  This seems to
leave irq issues (still!!)

PSM0 still can't allocate irq even though 12 isn't used anywhere else.
on the init hang, 3 processes are normally in RUNQ (one more on this boot,
but I've never seen this before); irq9, pagezero (I presume this is the
idle loop so should be in run) and init.

If I can get some pointers on what further to do with kdb, I'd be glad
to do so.  It somehow looks like irq9 process is never finishing; with
4 or 5 devices hung off one irq does the dispatch software work right?

(and why do irq 10 and 11 not get used?; I thought routed interrupts
weren't stuck with the 16-irq 2x8259 limitation either (I know apic ones
aren't).)
 
-- Pete
----------------------------------------------------------------------------
SMAP type=01 base=00000000 00000000 len=00000000 0009e000
SMAP type=02 base=00000000 0009e000 len=00000000 00002000
SMAP type=02 base=00000000 000d8000 len=00000000 00008000
SMAP type=02 base=00000000 000e4000 len=00000000 0001c000
SMAP type=01 base=00000000 00100000 len=00000000 1fbf0000
SMAP type=03 base=00000000 1fcf0000 len=00000000 0000c000
SMAP type=04 base=00000000 1fcfc000 len=00000000 00004000
SMAP type=01 base=00000000 1fd00000 len=00000000 00180000
SMAP type=02 base=00000000 1fe80000 len=00000000 00100000
SMAP type=02 base=00000000 1ff80000 len=00000000 00080000
SMAP type=02 base=00000000 ff800000 len=00000000 00400000
SMAP type=02 base=00000000 fffffc00 len=00000000 00000400
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD 5.0-CURRENT #19: Thu Oct 31 08:08:53 PST 2002
    pete@port2.altadena.net:/d/obj-s/current/usr/src/sys/PORT2
Preloaded elf kernel "/boot/kernel/kernel" at 0xc04e7000.
Preloaded elf module "/boot/kernel/firewire.ko" at 0xc04e70a8.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc04e7158.
Calibrating clock(s) ... TSC clock: 795410300 Hz, i8254 clock: 1193194 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254"  frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
Timecounter "TSC"  frequency 795407830 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (795.41-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x6b1  Stepping = 1
  Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory  = 535298048 (522752K bytes)
Physical memory chunk(s):
0x00001000 - 0x0009dfff, 643072 bytes (157 pages)
0x0050e000 - 0x1fceffff, 528359424 bytes (128994 pages)
0x1fd00000 - 0x1fe77fff, 1540096 bytes (376 pages)
avail memory = 513654784 (501616K bytes)
bios32: Found BIOS32 Service Directory header at 0xc00f6ba0
bios32: Entry = 0xfd871 (c00fd871)  Rev = 0  Len = 1
pcibios: PCI BIOS entry at 0xfd870+0x13a
pnpbios: Found PnP BIOS data at 0xc00f6bd0
pnpbios: Entry = f0000:880c  Rev = 1.0
Other BIOS signatures found:
Initializing GEOMetry subsystem
null: <null device, zero device>
mem: <memory & I/O>
Pentium Pro MTRR support enabled
random: <entropy source>
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <SONY   C1      > on motherboard
pci_open(1):	mode 1 addr port (0x0cf8) is 0x8000f904
pci_open(1a):	mode1res=0x80000000 (0x80000000)
pci_cfgcheck:	device 0 [class=060000] [hdr=00] is there (id=35758086)
Using $PIR table, 9 entries at 0xc00fdf30
PCI-Only Interrupts: none
Location  Bus Device Pin  Link  IRQs
embedded    2    5    A   0x69  3
embedded    2    8    A   0x68  9
embedded    0   29    A   0x60  9
embedded    0   29    B   0x63  9
embedded    0    2    A   0x60  9
embedded    0    1    A   0x60  9
ACPI timer looks GOOD min = 2, max = 3, width = 2
ACPI timer looks GOOD min = 2, max = 3, width = 2
ACPI timer looks GOOD min = 2, max = 3, width = 2
ACPI timer looks GOOD min = 2, max = 3, width = 2
ACPI timer looks GOOD min = 2, max = 3, width = 2
ACPI timer looks GOOD min = 2, max = 3, width = 2
ACPI timer looks GOOD min = 2, max = 3, width = 2
ACPI timer looks GOOD min = 2, max = 3, width = 2
ACPI timer looks GOOD min = 2, max = 3, width = 2
ACPI timer looks GOOD min = 2, max = 3, width = 2
Timecounter "ACPI-fast"  frequency 3579545 Hz
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_tz0: <thermal zone> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
---- initial configuration ------------------------
\_SB_.LNKA irq   9: [  9] low,level,sharable 0.1.0
\_SB_.LNKD irq   9: [  9] low,level,sharable 0.1.3
\_SB_.LNKA irq   9: [  9] low,level,sharable 0.2.0
\_SB_.LNKA irq   9: [  9] low,level,sharable 0.29.0
\_SB_.LNKD irq   9: [  9] low,level,sharable 0.29.1
---- before setting priority for links ------------
---- before fixup boot-disabled links -------------
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
\_SB_.LNKA irq   9: [  9] low,level,sharable 0.1.0
\_SB_.LNKD irq   9: [  9] low,level,sharable 0.1.3
\_SB_.LNKA irq   9: [  9] low,level,sharable 0.2.0
\_SB_.LNKA irq   9: [  9] low,level,sharable 0.29.0
\_SB_.LNKD irq   9: [  9] low,level,sharable 0.29.1
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
	map[10]: type 3, range 32, base 00000000, size  0, enabled
found->	vendor=0x8086, dev=0x3575, revid=0x04
	bus=0, slot=0, func=0
	class=06-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0106, statreg=0x2010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	map[10]: type 3, range 32, base e8000000, size 27, enabled
	map[14]: type 1, range 32, base e0000000, size 19, enabled
found->	vendor=0x8086, dev=0x3577, revid=0x04
	bus=0, slot=2, func=0
	class=03-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0007, statreg=0x0090, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=9
	powerspec 1  supports D0 D1 D3  current D0
	map[10]: type 3, range 32, base f0000000, size 27, enabled
	map[14]: type 1, range 32, base e0080000, size 19, enabled
found->	vendor=0x8086, dev=0x3577, revid=0x00
	bus=0, slot=2, func=1
	class=03-80-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0007, statreg=0x0090, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x09 (2250 ns)
	powerspec 1  supports D0 D1 D3  current D0
	map[20]: type 4, range 32, base 00001800, size  5, enabled
found->	vendor=0x8086, dev=0x2482, revid=0x02
	bus=0, slot=29, func=0
	class=0c-03-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=9
	map[20]: type 4, range 32, base 00001820, size  5, enabled
found->	vendor=0x8086, dev=0x2484, revid=0x02
	bus=0, slot=29, func=1
	class=0c-03-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=9
	map[20]: type 4, range 32, base 00001840, size  5, enabled
found->	vendor=0x8086, dev=0x2487, revid=0x02
	bus=0, slot=29, func=2
	class=0c-03-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=c, irq=255
found->	vendor=0x8086, dev=0x2448, revid=0x42
	bus=0, slot=30, func=0
	class=06-04-00, hdrtype=0x01, mfdev=0
	cmdreg=0x0007, statreg=0x0080, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns)
found->	vendor=0x8086, dev=0x248c, revid=0x02
	bus=0, slot=31, func=0
	class=06-01-00, hdrtype=0x00, mfdev=1
	cmdreg=0x000f, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	map[10]: type 4, range 32, base 000001f0, size  3, enabled
	map[14]: type 4, range 32, base 000003f4, size  2, enabled
	map[18]: type 4, range 32, base 00000170, size  3, enabled
	map[1c]: type 4, range 32, base 00000374, size  2, enabled
	map[20]: type 4, range 32, base 00001860, size  4, enabled
	map[24]: type 1, range 32, base e0100000, size 10, memory disabled
found->	vendor=0x8086, dev=0x248a, revid=0x02
	bus=0, slot=31, func=1
	class=01-01-8a, hdrtype=0x00, mfdev=0
	cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=255
	map[20]: type 4, range 32, base 00001880, size  5, enabled
found->	vendor=0x8086, dev=0x2483, revid=0x02
	bus=0, slot=31, func=3
	class=0c-05-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=255
	map[10]: type 4, range 32, base 00001c00, size  8, port disabled
	map[14]: type 4, range 32, base 000018c0, size  6, enabled
found->	vendor=0x8086, dev=0x2485, revid=0x02
	bus=0, slot=31, func=5
	class=04-01-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0000, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=9
	map[10]: type 4, range 32, base 00002400, size  8, port disabled
	map[14]: type 4, range 32, base 00002000, size  7, enabled
found->	vendor=0x8086, dev=0x2486, revid=0x02
	bus=0, slot=31, func=6
	class=07-03-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0000, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=255
agp0: <Intel 82830 (i830M GMCH) SVGA controller> mem 0xe0000000-0xe007ffff,0xe8000000-0xefffffff irq 9 at device 2.0 on pci0
agp0: detected 892k stolen memory
agp0: aperture size is 128M
pci0: <display> at device 2.1 (no driver attached)
uhci0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> port 0x1800-0x181f irq 9 at device 29.0 on pci0
usb0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> port 0x1820-0x183f irq 9 at device 29.1 on pci0
usb1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801CA/CAM (ICH3) USB controller USB-C> port 0x1840-0x185f at device 29.2 on pci0
pcib0: matched entry for 0.29.INTC (source \_SB_.LNKC)
pcib0: possible interrupts:  9
pcib0: slot 29 INTC routed to irq 9 via \_SB_.LNKC
usb2: <Intel 82801CA/CAM (ICH3) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
umass0: Sony USB Memory Stick Slot, rev 1.10/1.09, addr 2
umass0:0:0:-1: Attached to scbus0 as device 0
pcib1: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pcib1:   secondary bus     2
pcib1:   subordinate bus   2
pcib1:   I/O decode        0x3000-0x3fff
pcib1:   memory decode     0xe0200000-0xe02fffff
pcib1:   prefetched decode 0xfff00000-0xfffff
---- initial configuration ------------------------
\_SB_.LNKC irq   9: [  9] low,level,sharable 2.2.0
\_SB_.LNKE irq   9: [  9] low,level,sharable 2.8.0
\_SB_.LNKD irq   9: [  9] low,level,sharable 2.11.0
\_SB_.LNKA irq   9: [  9] low,level,sharable 2.11.1
---- before setting priority for links ------------
---- before fixup boot-disabled links -------------
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
\_SB_.LNKC irq   9: [  9] low,level,sharable 2.2.0
\_SB_.LNKE irq   9: [  9] low,level,sharable 2.8.0
\_SB_.LNKD irq   9: [  9] low,level,sharable 2.11.0
\_SB_.LNKA irq   9: [  9] low,level,sharable 2.11.1
pci2: <ACPI PCI bus> on pcib1
pci2: physical bus=2
	map[10]: type 1, range 32, base e0205000, size 11, enabled
	map[14]: type 1, range 32, base e0200000, size 14, enabled
found->	vendor=0x104c, dev=0x8023, revid=0x00
	bus=2, slot=2, func=0
	class=0c-00-10, hdrtype=0x00, mfdev=0
	cmdreg=0x0006, statreg=0x0210, cachelnsz=8 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x03 (750 ns), maxlat=0x04 (1000 ns)
	intpin=a, irq=255
	powerspec 2  supports D0 D1 D2 D3  current D0
found->	vendor=0x1180, dev=0x0475, revid=0x80
	bus=2, slot=5, func=0
	class=06-07-00, hdrtype=0x02, mfdev=0
	cmdreg=0x0007, statreg=0x0210, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=3
	powerspec 2  supports D0 D1 D2 D3  current D0
	map[10]: type 1, range 32, base e0204000, size 12, enabled
	map[14]: type 4, range 32, base 00003000, size  6, enabled
found->	vendor=0x8086, dev=0x1031, revid=0x42
	bus=2, slot=8, func=0
	class=02-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0007, statreg=0x0290, cachelnsz=8 (dwords)
	lattimer=0x42 (1980 ns), mingnt=0x08 (2000 ns), maxlat=0x38 (14000 ns)
	intpin=a, irq=9
	powerspec 2  supports D0 D1 D2 D3  current D0
found->	vendor=0x104c, dev=0xac50, revid=0x01
	bus=2, slot=11, func=0
	class=06-07-00, hdrtype=0x02, mfdev=0
	cmdreg=0x0000, statreg=0x0210, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x40 (16000 ns), maxlat=0x03 (750 ns)
	intpin=a, irq=255
	powerspec 1  supports D0 D1 D2 D3  current D0
XXXfw: vendid=104c, dev=8023
fwohci0: <1394 Open Host Controller Interface> mem 0xe0200000-0xe0203fff,0xe0205000-0xe02057ff at device 2.0 on pci2
fwohci0: Invalid irq 255
fwohci0: Please switch PNP-OS to 'No' in BIOS
device_probe_and_attach: fwohci0 attach returned 6
cbb0: <RF5C475 PCI-CardBus Bridge> irq 3 at device 5.0 on pci2
pcib1: device cbb0 requested decoded memory range 0xe0200000-0xe02fffff
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
fxp0: <Intel Pro/100 Ethernet> port 0x3000-0x303f mem 0xe0204000-0xe0204fff irq 9 at device 8.0 on pci2
pcib1: device fxp0 requested decoded memory range 0xe0204000-0xe0204fff
fxp0: using memory space register mapping
fxp0: Ethernet address 08:00:46:4e:96:17
fxp0: PCI IDs: 8086 1031 104d 8100 0042
fxp0: Dynamic Standby mode is disabled
inphy0: <i82562ET 10/100 media interface> on miibus0
inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bpf: fxp0 attached
cbb1: <TI1410 PCI-CardBus Bridge> at device 11.0 on pci2
pcib1: device cbb1 requested decoded memory range 0xe0200000-0xe02fffff
cardbus1: <CardBus bus> on cbb1
pccard1: <16-bit PCCard bus> on cbb1
pcib1: matched entry for 2.11.INTA (source \_SB_.LNKD)
pcib1: slot 11 INTA is routed to irq 9
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH3 ATA100 controller> port 0x1860-0x186f,0x374-0x377,0x170-0x177,0x3f4-0x3f7,0x1f0-0x1f7 mem 0xe0100000-0xe01003ff at device 31.1 on pci0
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0x1860
ata0: mask=03 ostat0=50 ostat2=00
ata0-master: ATAPI 00 00
ata0-slave: ATAPI 00 00
ata0: mask=03 stat0=50 stat1=00
ata0-master: ATA 01 a5
ata0: devices=01
ata0: at 0x1f0 irq 14 on atapci0
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0x1868
ata1: mask=03 ostat0=00 ostat2=00
ata1-master: ATAPI 00 00
ata1-slave: ATAPI 00 00
ata1: mask=03 stat0=00 stat1=00
ata1: devices=00
ata1: at 0x170 irq 15 on atapci0
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
pci0: <multimedia, audio> at device 31.5 (no driver attached)
pci0: <simple comms> at device 31.6 (no driver attached)
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x1d0000
psm0: unable to allocate IRQ
acpi_ec0: <embedded controller> port 0x66,0x62 on acpi0
sio0: irq maps: 0x201 0x211 0x201 0x201
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A, console
unknown: not probed (disabled)
unknown: not probed (disabled)
ppc0: using extended I/O port range
ppc0: ECP SPP ECP+EPP SPP
ppc0 port 0x778-0x77f,0x378-0x37f irq 7 drq 3 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/15 bytes threshold
plip0: <PLIP network interface> on ppbus0
bpf: lp0 attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
fdc0: <enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
acpi_cmbat0: <Control method Battery> on acpi0
acpi_acad0: <AC adapter> on acpi0
unknown: not probed (disabled)
unknown: not probed (disabled)
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
fdc: fdc0 already exists; skipping it
ppc: ppc0 already exists; skipping it
sio: sio0 already exists; skipping it
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROMs> at iomem 0xdc000-0xdffff,0xd8000-0xdbfff,0xc0000-0xcffff on isa0
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1 failed to probe at port 0x3e2 iomem 0xd4000 irq 11 on isa0
pmtimer0 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x100>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 02 55 81 
bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96 
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff 
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff 
EGA/VGA parameters to be used for mode 24
50 18 10 00 00 00 03 00 02 67 5f 4f 50 02 55 81 
bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96 
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff 
vt0 failed to probe on isa0
isa_probe_children: probing PnP devices
BIOS Geometries:
 0:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads, 1..63=63 sectors
 0 accounted for
Device configuration finished.
procfs registered
Timecounters tick every 10.000 msec
bpf: lo0 attached
acpi_cpu0: set speed to 100.0%
acpi_cpu: CPU throttling enabled, 8 steps from 100% to 12.5%
system power profile changed to 'economy'
acpi_cpu0: set speed to 50.0%
acpi_acad0: Off Line
cbb0: Unsupported card type detected
cbb1: Unsupported card type detected
ad0: success setting UDMA5 on Intel chip
GEOM: new disk ad0
ar: FreeBSD check1 failed
ad0: <TOSHIBA MK4018GAS/Q1.02 C> ATA-5 disk at ata0-master
ad0: 38154MB (78140160 sectors), 77520 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, UDMA100
ad0: piomode=4 dmamode=2 udmamode=5 cblid=1
Slice 1:
0000   00 01 01 00 07 fe ff ce 3f 00 00 00 d0 00 ef 00  |........?.......|
[0] f:00 typ:7 s(CHS):0/1/1 e(CHS):206/254/255 s:63 l:15663312
GEOM: Add ad0s1, start 32256 length 8019615744 end 8019647999
Slice 2:
0000   80 00 c1 cf a5 fe ff ff 0f 01 ef 00 8a f5 7f 00  |................|
[1] f:80 typ:165 s(CHS):207/0/193 e(CHS):255/254/255 s:15663375 l:8385930
GEOM: Add ad0s2, start 8019648000 length 4293596160 end 12313244159
Slice 3:
0000   00 ff ff ff a5 fe ff ff 99 f6 6e 01 8a f5 7f 00  |..........n.....|
[2] f:00 typ:165 s(CHS):255/255/255 e(CHS):255/254/255 s:24049305 l:8385930
GEOM: Add ad0s3, start 12313244160 length 4293596160 end 16606840319
Slice 4:
0000   00 ff ff ff a5 fe ff ff 23 ec ee 01 dd 66 b9 02  |........#....f..|
[3] f:00 typ:165 s(CHS):255/255/255 e(CHS):255/254/255 s:32435235 l:45704925
GEOM: Add ad0s4, start 16606840320 length 23400921600 end 40007761919
GEOM: Configure ad0s2a, start 0 length 268435456 end 268435455
GEOM: Configure ad0s2b, start 536870912 length 536870912 end 1073741823
GEOM: Configure ad0s2c, start 0 length 4293596160 end 4293596159
GEOM: Configure ad0s2e, start 268435456 length 268435456 end 536870911
GEOM: Configure ad0s2f, start 1073741824 length 3219854336 end 4293596159
GEOM: Configure ad0s3a, start 0 length 268435456 end 268435455
GEOM: Configure ad0s3b, start 536870912 length 536870912 end 1073741823
GEOM: Configure ad0s3c, start 0 length 4293596160 end 4293596159
GEOM: Configure ad0s3e, start 268435456 length 268435456 end 536870911
GEOM: Configure ad0s3f, start 1073741824 length 3219854336 end 4293596159
GEOM: Configure ad0s4a, start 0 length 23400921600 end 23400921599
GEOM: Configure ad0s4c, start 0 length 23400921600 end 23400921599
(probe0:umass-sim0:0:0:0): INQUIRY. CDB: 12 0 0 0 24 0 
(probe0:umass-sim0:0:0:0): CAM Status: SCSI Status Error
(probe0:umass-sim0:0:0:0): SCSI Status: Check Condition
(probe0:umass-sim0:0:0:0): UNIT ATTENTION asc:29,0
(probe0:umass-sim0:0:0:0): Power on, reset, or bus device reset occurred
(probe0:umass-sim0:0:0:0): (probe0:umass-sim0:0:0:0): INQUIRY. CDB: 12 0 0 0 24 0 (probe0:umass-sim0:0:0:0): UNIT ATTENTION asc:29,0
(probe0:umass-sim0:0:0:0): Power on, reset, or bus device reset occurred
Retrying Command (per Sense Data)
(probe0:umass-sim0:0:0:0): Retrying Command
pass0 at umass-sim0 bus 0 target 0 lun 0
pass0: <Sony MSC-U03 1.00> Removable Direct Access SCSI-0 device 
pass0: Serial Number 3
pass0: 1.000MB/s transfers
GEOM: new disk da0
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <Sony MSC-U03 1.00> Removable Direct Access SCSI-0 device 
da0: Serial Number 3
da0: 1.000MB/s transfers
da0: 3MB (7904 512 byte sectors: 0H 0S/T 0C)
Slice 1:
0000   80 01 0c 00 01 01 10 f5 1b 00 00 00 a5 1e 00 00  |................|
[0] f:80 typ:1 s(CHS):0/1/12 e(CHS):245/1/16 s:27 l:7845
GEOM: Add da0s1, start 13824 length 4016640 end 4030463
Mounting root from ufs:/dev/ad0s2a
start_init: trying /sbin/init
Debugger("manual escape to debugger")
Stopped at      Debugger+0x54:  xchgl   %ebx,in_Debugger.0
db> tr
Debugger(c036bc82,4,1,0,1) at Debugger+0x54
scgetc(c4595000,2,80296,1d6,c45d3180) at scgetc+0x445
sckbdevent(c03ed380,0,c4595000,c0389d20,8) at sckbdevent+0x1d0
atkbd_intr(c03ed380,0,d71c9d0c,c01e6ba2,c03ed380) at atkbd_intr+0x2c
atkbd_isa_intr(c03ed380,0,c035261c,216,c45b7000) at atkbd_isa_intr+0x21
ithread_loop(c45b6300,d71c9d48,c035236e,354,0) at ithread_loop+0x182
fork_exit(c01e6a20,c45b6300,d71c9d48) at fork_exit+0xa5
fork_trampoline() at fork_trampoline+0x1a
--- trap 0x1, eip = 0, esp = 0xd71c9d7c, ebp = 0 ---
db> tr 1
mi_switch(c13098f0,ca,c0357b3d,f2,2800) at mi_switch+0x1e1
ast(d7187d48) at ast+0x3d0
doreti_ast() at doreti_ast+0x1a
db> ps
  pid   proc     addr    uid  ppid  pgrp  flag   stat  wmesg    wchan  cmd
   39 c46b0700 e0782000    0     0     0 0000204 norm[SLPQ  vlruwt c46b0700][SLP] vnlru
   38 c46b08c0 e0783000    0     0     0 0000204 norm[SLPQ  syncer c038af80][SLP] syncer
   37 c46b0a80 e07bd000    0     0     0 0000204 norm[SLPQ  psleep c03e9a24][SLP] bufdaemon
    9 c46b0c40 e07be000    0     0     0 000020c norm[RUNQ] pagezero
    8 c46b0e00 e07bf000    0     0     0 0000204 norm[SLPQ  psleep c03ecd4c][SLP] vmdaemon
    7 c46b3000 e07c0000    0     0     0 0000204 norm[SLPQ  psleep c039e1b8][SLP] pagedaemon
   36 c4549540 d86e4000    0     0     0 0000204 new [IWAIT] irq8: rtc
   35 c4549700 d86e5000    0     0     0 0000204 new [IWAIT] irq0: clk
   34 c45498c0 d86e6000    0     0     0 0000204 norm[IWAIT] irq6: fdc0
   33 c4549a80 d86e7000    0     0     0 0000204 norm[IWAIT] irq7: ppc0
   32 c4549c40 d86e8000    0     0     0 0000204 new [IWAIT] irq4: sio0
   31 c4549e00 d86e9000    0     0     0 0000204 new [IWAIT] swi0: tty:sio
   30 c45b7000 e0773000    0     0     0 0000204 norm[CPU 0] irq1: atkbd0
   29 c45b71c0 e0774000    0     0     0 0000204 new [IWAIT] irq15: ata1
   28 c45b7380 e0775000    0     0     0 0000204 norm[IWAIT] irq14: ata0
    6 c45b7540 e0776000    0     0     0 0000204 norm[CVQ  cbb cv c454db4c][SLP] cbb1
    5 c45b7700 e0777000    0     0     0 0000204 norm[CVQ  cbb cv c454d34c][SLP] cbb0
   27 c45b78c0 e0778000    0     0     0 0000204 new [IWAIT] irq3: cbb0
   26 c130f1c0 d71df000    0     0     0 0000204 norm[SLPQ  usbevt c45a5210][SLP] usb2
   25 c130f380 d71e0000    0     0     0 0000204 norm[SLPQ  usbevt c45ac210][SLP] usb1
--More--   24 c130f540 d71e1000    0     0     0 0000204 norm[SLPQ  usbtsk c0382e3c][SLP] usbtask
   23 c130f700 d71e2000    0     0     0 0000204 norm[SLPQ  usbevt c4538210][SLP] usb0
   22 c130f8c0 d71e3000    0     0     0 0000204 norm[SLPQ  nothing c04d7df4][SLP] acpi_thermal
   21 c130fa80 d71e4000    0     0     0 0000204 norm[RUNQ] irq9: cbb1 fxp0++++
   20 c130fc40 d71e5000    0     0     0 0000204 new [IWAIT] irq13:
   19 c130fe00 d71e6000    0     0     0 0000204 norm[IWAIT] swi5: acpitaskq
   18 c4549000 d86a8000    0     0     0 0000204 norm[IWAIT] swi3: cambio
   17 c45491c0 d86a9000    0     0     0 0000204 new [IWAIT] swi2: camnet
   16 c4549380 d86aa000    0     0     0 0000204 new [IWAIT] swi5: task queue
   15 c1308000 d7163000    0     0     0 0000204 norm[SLPQ   sleep c03b1d00][SLP] random
    4 c13081c0 d71d6000    0     0     0 0000204 norm[SLPQ  g_down c0384790][SLP] g_down
    3 c1308380 d71d7000    0     0     0 0000204 norm[SLPQ    g_up c038478c][SLP] g_up
    2 c1308540 d71d8000    0     0     0 0000204 norm[SLPQ  g_events c0384784][SLP] g_event
   14 c1308700 d71d9000    0     0     0 0000204 new [IWAIT] swi1: net
   13 c13088c0 d71da000    0     0     0 0000204 new [IWAIT] swi4: vm
   12 c1308a80 d71db000    0     0     0 000020c norm[RUNQ] swi6: tty:sio clock
   11 c1308c40 d71dc000    0     0     0 000020c norm[Can run] idle
    1 c1308e00 d71dd000    0     0     0 0004200 norm[RUNQ] init
   10 c130f000 d71de000    0     0     0 0000204 norm[CVQ  ktrace c03c0d64][SLP] ktrace
    0 c0385440 c0507000    0     0     0 0000200 norm[SLPQ   sched c0385440][SLP] swapper
db> tr 12
mi_switch(c0389cc0,0,c035261c,223,c1308a80) at mi_switch+0x1e1
ithread_loop(c12f9900,d718dd48,c035236e,354,20) at ithread_loop+0x23a
fork_exit(c01e6a20,c12f9900,d718dd48) at fork_exit+0xa5
fork_trampoline() at fork_trampoline+0x1a
--- trap 0x1, eip = 0, esp = 0xd718dd7c, ebp = 0 ---
db> tr 21
mi_switch(9,0,c035261c,223,c130fa80) at mi_switch+0x1e1
ithread_loop(c12fa500,d7172d48,c035236e,354,0) at ithread_loop+0x23a
fork_exit(c01e6a20,c12fa500,d7172d48) at fork_exit+0xa5
fork_trampoline() at fork_trampoline+0x1a
--- trap 0x1, eip = 0, esp = 0xd7172d7c, ebp = 0 ---
db> tr 9
mi_switch(c130a9c0,0,c035261c,184,198) at mi_switch+0x1e1
ithread_schedule(c4599a00,1,1,c46b2270,ff) at ithread_schedule+0x135
sched_ithd(e) at sched_ithd+0x43
Xintr14() at Xintr14+0x6c
--- interrupt, eip = 0xc031abc9, esp = 0xe078fca4, ebp = 0xe078fcb8 ---
i686_pagezero(c06bbbb8,0,c0369523,53,c46b2270) at i686_pagezero+0x35
vm_page_zero_idle(c0389cc0,0,c0369523,88,e078fd0c) at vm_page_zero_idle+0xa0
vm_pagezero(0,e078fd48,c035236e,354,0) at vm_pagezero+0xee
fork_exit(c02e5e20,0,e078fd48) at fork_exit+0xa5
fork_trampoline() at fork_trampoline+0x1a
--- trap 0x1, eip = 0, esp = 0xe078fd7c, ebp = 0 ---
db> tr 1
mi_switch(c13098f0,ca,c0357b3d,f2,2800) at mi_switch+0x1e1
ast(d7187d48) at ast+0x3d0
doreti_ast() at doreti_ast+0x1a
db> ?
Bad character
?
db> help
print       p           examine     x           search      set         write
w           delete      d           break       dwatch      watch       dhwatch
hwatch      step        s           continue    c           until       next
match       trace       call        show        ps          gdb         reset
kill        panic
db> reset
------------------------------------------------------

To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-current" in the body of the message




Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200210312115.g9VLFKkK038452>