Skip site navigation (1)Skip section navigation (2)
Date:      Fri, 08 Jul 2005 11:47:22 -0400
From:      Mike Tancsa <mike@sentex.net>
To:        John Baldwin <jhb@FreeBSD.org>
Cc:        freebsd-current@FreeBSD.org
Subject:   Re: 6.0-CURRENT SNAP004 hangs on amr
Message-ID:  <6.2.1.2.0.20050708110446.07de5768@64.7.153.2>
In-Reply-To: <200507081006.43609.jhb@FreeBSD.org>
References:  <70e8236f05070208212e36c375@mail.gmail.com> <200507071658.27361.jhb@FreeBSD.org> <6.2.1.2.0.20050707220038.08329918@64.7.153.2> <200507081006.43609.jhb@FreeBSD.org>

next in thread | previous in thread | raw e-mail | index | archive | help
--=====================_1996631594==_
Content-Type: text/plain; charset="us-ascii"; format=flowed

At 10:06 AM 08/07/2005, John Baldwin wrote:
>On Thursday 07 July 2005 10:09 pm, Mike Tancsa wrote:
> > At 04:58 PM 07/07/2005, John Baldwin wrote:
> > >Crud, it's off in the weeds. :(  Can you do a boot -v and get the lines
> > > after 'pcib3:'?
> >
> > Here you go
>
>Ok, I see why it is badly confused in the non-APIC and non-ACPI case though I
>don't know why it is panicing.  (FWIW, it is trying to route all interrupts
>to IRQ 14 because your $PIR is all busted *sigh*).  BIOS writers suck.

Unfortunately, this is the latest version of the BIOS from Dell.


>Anyway, I still need a simple matrix of what works and what doesn't work
>first (if I got one earlier I lost it):
>
>ACPI/APIC - amr0 gets no interrupts, hangs after boot

yes, it hangs either with amr or perhaps ata.  yesterday I was trying just 
a netboot and it seemed to work if I pulled the card and did not have the 
ata code in the driver, although I had not setup the fstab to properly 
work, but the fact that I was complaining about mounting root implies it 
got farther along.  If you feel this is worth checking out, I could pull 
the amr card again, and try and properly netboot a kernel and mount root 
via nfs on 6.x.

On RELENG_5 it sometimes works if I disable ata in the kernel.   I attached 
the boot-v from releng5.  6.x hangs (also attached)



>ACPI/no-APIC - amr0 gets no interrupts, hangs after boot?

Panic.  This case should be in the last email I sent.
OK set hint.apic.0.disabled=1
OK load acpi.ko

kernel trap 12 with interrupts disabled


Fatal trap 12: page fault while in kernel mode
cpuid = 0; apic id = 00
fault virtual address   = 0xba9f
fault code              = supervisor read, page not present
instruction pointer     = 0x8:0xc00fd141
stack pointer           = 0x10:0xc0c2094c
frame pointer           = 0x10:0xc0c209b8
code segment            = base 0x0, limit 0xfffff, type 0x1b
                         = DPL 0, pres 1, def32 1, gran 1
processor eflags        = resume, IOPL = 0
current process         = 0 (swapper)
[thread pid 0 tid 0 ]
Stopped at      0xc00fd141:     cmpb    %cs:0xba9f,%bh
db> trace
Tracing pid 0 tid 0 td 0xc07d1c60
kernbase(e0b,c07029d1,c00fc860,c00fc86b,c0c209f8) at 0xc00fd141
db>


>no-ACPI/APIC - ???

RELENG_5, all is happy. 6.x hang.


>no-ACPI/no-APIC - busted $PIR causes the code to go off into the weeds
>
>Is that summary more or less correct?  Can you test the missing case?  Also,
>is there any difference between 5.4 and 6.0 in this table?

I have yet to find a combo that allows me to boot 6.x with the amr card in.

         ---Mike




>--
>John Baldwin <jhb@FreeBSD.org>  <><  http://www.FreeBSD.org/~jhb/
>"Power Users Use the Power to Serve"  =  http://www.FreeBSD.org

--=====================_1996631594==_
Content-Type: text/plain; charset="us-ascii"
Content-Disposition: attachment; filename="releng5-acpi-apic.txt"

OK load acpi.ko
/boot/kernel/acpi.ko text=0x414dc data=0x1dc4+0x112c syms=[0x4+0x7670+0x4+0x9d05]
OK boot -v
KDB: debugger backends: ddb
KDB: current backend: ddb
SMAP type=01 base=0000000000000000 len=00000000000a0000
SMAP type=01 base=0000000000100000 len=000000007fefe000
SMAP type=02 base=000000007fffe000 len=0000000000002000
SMAP type=02 base=00000000fec00000 len=0000000000010000
SMAP type=02 base=00000000fee00000 len=0000000000010000
SMAP type=02 base=00000000fff80000 len=0000000000080000
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 5.4-STABLE #1: Thu Jul  7 18:55:23 EDT 2005
    mdtancsa@hippo.sentex.ca:/usr/obj/usr/src/sys/hippo
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0904000.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc09041d8.
Calibrating clock(s) ... i8254 clock: 1193227 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 500019728 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (500.02-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x672  Stepping = 2
  Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory  = 2147475456 (2047 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000000c28000 - 0x000000007dbcdfff, 2096783360 bytes (511910 pages)
avail memory = 2096021504 (1998 MB)
MP Configuration Table version 1.4 found at 0xc00f0000
APIC: Using the MPTable enumerator.
SMP: Added CPU 3 (BSP)
SMP: Added CPU 0 (AP)
SMP: Added CPU 1 (AP)
SMP: Added CPU 2 (AP)
MPTable: <DELL     PowerEdge 83>
APIC ID: physical 0, logical 0:0
APIC ID: physical 1, logical 0:1
APIC ID: physical 2, logical 0:2
APIC ID: physical 3, logical 0:3
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
 cpu0 (BSP): APIC ID:  3
 cpu1 (AP): APIC ID:  0
 cpu2 (AP): APIC ID:  1
 cpu3 (AP): APIC ID:  2
bios32: Found BIOS32 Service Directory header at 0xc00ffe80
bios32: Entry = 0xffe90 (c00ffe90)  Rev = 0  Len = 1
pcibios: PCI BIOS entry at 0xf0000+0xcc4e
pnpbios: Found PnP BIOS data at 0xc00fe2d0
pnpbios: Entry = f0000:e2f4  Rev = 1.0
Other BIOS signatures found:
ioapic0: Changing APIC ID to 4
ioapic0: Assuming intbase of 0
ioapic0: Routing external 8259A's -> intpin 0
ioapic0: intpin 0 -> ExtINT (edge, high)
ioapic0: intpin 1 -> ISA IRQ 1 (edge, high)
ioapic0: intpin 2 -> ISA IRQ 2 (edge, high)
ioapic0: intpin 3 -> ISA IRQ 3 (edge, high)
ioapic0: intpin 4 -> ISA IRQ 4 (edge, high)
ioapic0: intpin 5 -> ISA IRQ 5 (edge, high)
ioapic0: intpin 6 -> ISA IRQ 6 (edge, high)
ioapic0: intpin 7 -> ISA IRQ 7 (edge, high)
ioapic0: intpin 8 -> ISA IRQ 8 (edge, high)
ioapic0: intpin 9 -> ISA IRQ 9 (edge, high)
ioapic0: intpin 10 -> ISA IRQ 10 (edge, high)
ioapic0: intpin 11 -> ISA IRQ 11 (edge, high)
ioapic0: intpin 12 -> ISA IRQ 12 (edge, high)
ioapic0: intpin 13 -> ISA IRQ 13 (edge, high)
ioapic0: intpin 14 -> ISA IRQ 14 (edge, high)
ioapic0: intpin 15 -> ISA IRQ 15 (edge, high)
ioapic0: intpin 16 -> PCI IRQ 16 (level, low)
ioapic0: intpin 17 -> PCI IRQ 17 (level, low)
ioapic0: intpin 18 -> PCI IRQ 18 (level, low)
ioapic0: intpin 19 -> PCI IRQ 19 (level, low)
ioapic0: intpin 20 -> PCI IRQ 20 (level, low)
ioapic0: intpin 21 -> PCI IRQ 21 (level, low)
ioapic0: intpin 22 -> PCI IRQ 22 (level, low)
ioapic0: intpin 23 -> PCI IRQ 23 (level, low)
ioapic0: intpin 1 bus ISA
ioapic0: intpin 1 trigger: edge
ioapic0: intpin 1 polarity: high
ioapic0: intpin 2 bus ISA
ioapic0: Routing IRQ 0 -> intpin 2
ioapic0: intpin 2 trigger: edge
ioapic0: intpin 2 polarity: high
ioapic0: intpin 3 bus ISA
ioapic0: intpin 3 trigger: edge
ioapic0: intpin 3 polarity: high
ioapic0: intpin 4 bus ISA
ioapic0: intpin 4 trigger: edge
ioapic0: intpin 4 polarity: high
ioapic0: intpin 5 bus ISA
ioapic0: intpin 5 trigger: edge
ioapic0: intpin 5 polarity: high
ioapic0: intpin 6 bus ISA
ioapic0: intpin 6 trigger: edge
ioapic0: intpin 6 polarity: high
ioapic0: intpin 7 bus ISA
ioapic0: intpin 7 trigger: edge
ioapic0: intpin 7 polarity: high
ioapic0: intpin 8 bus ISA
ioapic0: intpin 8 trigger: edge
ioapic0: intpin 8 polarity: high
ioapic0: intpin 9 bus ISA
ioapic0: intpin 9 trigger: edge
ioapic0: intpin 9 polarity: high
ioapic0: intpin 12 bus ISA
ioapic0: intpin 12 trigger: edge
ioapic0: intpin 12 polarity: high
ioapic0: intpin 15 bus ISA
ioapic0: intpin 15 trigger: edge
ioapic0: intpin 15 polarity: high
ioapic0: intpin 16 bus PCI
ioapic0: intpin 16 trigger: level
ioapic0: intpin 16 polarity: low
ioapic0: intpin 16 bus PCI
ioapic0: intpin 16 trigger: level
ioapic0: intpin 16 polarity: low
ioapic0: intpin 16 bus PCI
ioapic0: intpin 16 trigger: level
ioapic0: intpin 16 polarity: low
ioapic0: intpin 16 bus PCI
ioapic0: intpin 16 trigger: level
ioapic0: intpin 16 polarity: low
ioapic0: intpin 16 bus PCI
ioapic0: intpin 16 trigger: level
ioapic0: intpin 16 polarity: low
ioapic0: intpin 17 bus PCI
ioapic0: intpin 17 trigger: level
ioapic0: intpin 17 polarity: low
ioapic0: intpin 17 bus PCI
ioapic0: intpin 17 trigger: level
ioapic0: intpin 17 polarity: low
ioapic0: intpin 17 bus PCI
ioapic0: intpin 17 trigger: level
ioapic0: intpin 17 polarity: low
ioapic0: intpin 17 bus PCI
ioapic0: intpin 17 trigger: level
ioapic0: intpin 17 polarity: low
ioapic0: intpin 17 bus PCI
ioapic0: intpin 17 trigger: level
ioapic0: intpin 17 polarity: low
ioapic0: intpin 18 bus PCI
ioapic0: intpin 18 trigger: level
ioapic0: intpin 18 polarity: low
ioapic0: intpin 18 bus PCI
ioapic0: intpin 18 trigger: level
ioapic0: intpin 18 polarity: low
ioapic0: intpin 18 bus PCI
ioapic0: intpin 18 trigger: level
ioapic0: intpin 18 polarity: low
ioapic0: intpin 18 bus PCI
ioapic0: intpin 18 trigger: level
ioapic0: intpin 18 polarity: low
ioapic0: intpin 19 bus PCI
ioapic0: intpin 19 trigger: level
ioapic0: intpin 19 polarity: low
ioapic0: intpin 19 bus PCI
ioapic0: intpin 19 trigger: level
ioapic0: intpin 19 polarity: low
ioapic0: intpin 19 bus PCI
ioapic0: intpin 19 trigger: level
ioapic0: intpin 19 polarity: low
ioapic0: intpin 19 bus PCI
ioapic0: intpin 19 trigger: level
ioapic0: intpin 19 polarity: low
ioapic0: intpin 20 bus PCI
ioapic0: intpin 20 trigger: level
ioapic0: intpin 20 polarity: low
ioapic0: intpin 20 bus PCI
ioapic0: intpin 20 trigger: level
ioapic0: intpin 20 polarity: low
ioapic0: intpin 20 bus PCI
ioapic0: intpin 20 trigger: level
ioapic0: intpin 20 polarity: low
ioapic0: intpin 20 bus PCI
ioapic0: intpin 20 trigger: level
ioapic0: intpin 20 polarity: low
ioapic0: intpin 21 bus PCI
ioapic0: intpin 21 trigger: level
ioapic0: intpin 21 polarity: low
ioapic0: intpin 22 bus PCI
ioapic0: intpin 22 trigger: level
ioapic0: intpin 22 polarity: low
lapic: Routing ExtINT -> LINT0
lapic: LINT0 trigger: edge
lapic: LINT0 polarity: active-high
lapic: Routing NMI -> LINT1
lapic: LINT1 trigger: edge
lapic: LINT1 polarity: active-high
ioapic0 <Version 1.1> irqs 0-23 on motherboard
cpu0 BSP:
     ID: 0x03000000   VER: 0x00040011 LDR: 0x08000000 DFR: 0x0fffffff
  lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
mem: <memory>
Pentium Pro MTRR support enabled
io: <I/O>
null: <null device, zero device>
random: <entropy source, Software, Yarrow>
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
cpu0 on motherboard
cpu1 on motherboard
cpu2 on motherboard
cpu3 on motherboard
pci_open(1):    mode 1 addr port (0x0cf8) is 0x80008070
pci_open(1a):   mode1res=0x80000000 (0x80000000)
pci_cfgcheck:   device 0 1 2 [class=060100] [hdr=80] is there (id=71108086)
pcibios: BIOS version 2.10
Found $PIR table, 11 entries at 0xc00fc7a0
PCI-Only Interrupts: none
Location  Bus Device Pin  Link  IRQs
embedded    0    2    A   0x64  14
embedded    0    2    B   0x65  15
embedded    0    2    D   0x63  3 4 5 6 7 10 11 12 14
embedded    1    4    A   0x65  3 4 5 6 7 10 11 12 14
embedded    1    6    A   0x66  3 4 5 6 7 10 11 12 14
embedded    1    8    A   0x64  3 4 5 6 7 10 11 12 14
slot 1      0    6    A   0x69  3 4 5 6 7 10 11 12 14
slot 1      0    6    B   0x64  3 4 5 6 7 10 11 12 14
slot 1      0    6    C   0x67  3 4 5 6 7 10 11 12 14
slot 1      0    6    D   0x68  3 4 5 6 7 10 11 12 14
slot 2      0    8    A   0x68  3 4 5 6 7 10 11 12 14
slot 2      0    8    B   0x69  3 4 5 6 7 10 11 12 14
slot 2      0    8    C   0x64  3 4 5 6 7 10 11 12 14
slot 2      0    8    D   0x67  3 4 5 6 7 10 11 12 14
slot 3      0   10    A   0x67  3 4 5 6 7 10 11 12 14
slot 3      0   10    B   0x68  3 4 5 6 7 10 11 12 14
slot 3      0   10    C   0x69  3 4 5 6 7 10 11 12 14
slot 3      0   10    D   0x64  3 4 5 6 7 10 11 12 14
slot 4      2    1    A   0x63  3 4 5 6 7 10 11 12 14
slot 4      2    1    B   0x60  3 4 5 6 7 10 11 12 14
slot 4      2    1    C   0x61  3 4 5 6 7 10 11 12 14
slot 4      2    1    D   0x62  3 4 5 6 7 10 11 12 14
slot 5      2    3    A   0x62  3 4 5 6 7 10 11 12 14
slot 5      2    3    B   0x63  3 4 5 6 7 10 11 12 14
slot 5      2    3    C   0x60  3 4 5 6 7 10 11 12 14
slot 5      2    3    D   0x61  3 4 5 6 7 10 11 12 14
slot 6      2    5    A   0x61  3 4 5 6 7 10 11 12 14
slot 6      2    5    B   0x62  3 4 5 6 7 10 11 12 14
slot 6      2    5    C   0x63  3 4 5 6 7 10 11 12 14
slot 6      2    5    D   0x60  3 4 5 6 7 10 11 12 14
slot 7      2    7    A   0x60  3 4 5 6 7 10 11 12 14
slot 7      2    7    B   0x61  3 4 5 6 7 10 11 12 14
slot 7      2    7    C   0x62  3 4 5 6 7 10 11 12 14
slot 7      2    7    D   0x63  3 4 5 6 7 10 11 12 14
pcib0: <MPTable Host-PCI bridge> pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
pci0: physical bus=0
found-> vendor=0x8086, dev=0x7110, revid=0x02
        bus=0, slot=2, func=0
        class=06-01-00, hdrtype=0x00, mfdev=1
        cmdreg=0x000f, statreg=0x0280, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        map[20]: type 4, range 32, base 00000000, size  4, port disabled
found-> vendor=0x8086, dev=0x7111, revid=0x01
        bus=0, slot=2, func=1
        class=01-01-80, hdrtype=0x00, mfdev=0
        cmdreg=0x0000, statreg=0x0280, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        map[20]: type 4, range 32, base 00000000, size  5, port disabled
found-> vendor=0x8086, dev=0x7112, revid=0x01
        bus=0, slot=2, func=2
        class=0c-03-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0000, statreg=0x0280, cachelnsz=0 (dwords)
        lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=d, irq=255
        map[90]: type 4, range 32, base 00000850, size  4, enabled
found-> vendor=0x8086, dev=0x7113, revid=0x02
        bus=0, slot=2, func=3
        class=06-80-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        map[10]: type 3, range 32, base ee000000, size 24, enabled
        map[14]: type 4, range 32, base 0000dc00, size  8, enabled
        map[18]: type 1, range 32, base eff00000, size 12, enabled
found-> vendor=0x1002, dev=0x4749, revid=0x5c
        bus=0, slot=4, func=0
        class=03-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x00a7, statreg=0x0280, cachelnsz=8 (dwords)
        lattimer=0x20 (960 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x84ca, revid=0x03
        bus=0, slot=16, func=0
        class=06-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x84cb, revid=0x02
        bus=0, slot=18, func=0
        class=06-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0116, statreg=0x2280, cachelnsz=8 (dwords)
        lattimer=0x48 (2160 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x84cb, revid=0x02
        bus=0, slot=19, func=0
        class=06-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0116, statreg=0x0280, cachelnsz=8 (dwords)
        lattimer=0x48 (2160 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x84cb, revid=0x02
        bus=0, slot=20, func=0
        class=06-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0116, statreg=0x2280, cachelnsz=8 (dwords)
        lattimer=0x48 (2160 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
isab0: <PCI-ISA bridge> at device 2.0 on pci0
isa0: <ISA bus> on isab0
pci0: <mass storage, ATA> at device 2.1 (no driver attached)
pci0: <serial bus, USB> at device 2.2 (no driver attached)
piix0: <PIIX Timecounter> port 0x850-0x85f at device 2.3 on pci0
Timecounter "PIIX" frequency 3579545 Hz quality 0
pci0: <display, VGA> at device 4.0 (no driver attached)
pcib1: <MPTable Host-PCI bridge> pcibus 1 on motherboard
pci1: <PCI bus> on pcib1
pci1: physical bus=1
pcib2: <MPTable Host-PCI bridge> pcibus 2 on motherboard
pci2: <PCI bus> on pcib2
pci2: physical bus=2
        map[10]: type 1, range 32, base feb20000, size 17, enabled
        map[14]: type 1, range 32, base feb00000, size 17, enabled
        map[18]: type 4, range 32, base 0000ecc0, size  6, enabled
pcib2: slot 3 INTA routed to irq 18
found-> vendor=0x8086, dev=0x1076, revid=0x00
        bus=2, slot=3, func=0
        class=02-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0117, statreg=0x0230, cachelnsz=8 (dwords)
        lattimer=0x20 (960 ns), mingnt=0xff (63750 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=18
        powerspec 2  supports D0 D3  current D0
        MSI supports 1 message, 64 bit
found-> vendor=0x8086, dev=0xb154, revid=0x00
        bus=2, slot=7, func=0
        class=06-04-00, hdrtype=0x01, mfdev=0
        cmdreg=0x0107, statreg=0x02b0, cachelnsz=0 (dwords)
        lattimer=0x20 (960 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns)
em0: <Intel(R) PRO/1000 Network Connection, Version - 1.7.35> port 0xecc0-0xecff mem 0xfeb00000-0xfeb1ffff,0xfeb20000-0xfeb3ffff ir2
em0: Reserved 0x20000 bytes for rid 0x10 type 3 at 0xfeb20000
em0: Reserved 0x40 bytes for rid 0x18 type 4 at 0xecc0
em0: [MPSAFE]
em0: bpf attached
em0: Ethernet address: 00:0e:0c:5d:f8:ca
em0:  Speed:N/A  Duplex:N/A
pcib3: <MPTable PCI-PCI bridge> at device 7.0 on pci2
pcib3:   secondary bus     3
pcib3:   subordinate bus   4
pcib3:   I/O decode        0xf000-0xffff
pcib3:   memory decode     0xfe800000-0xfeafffff
pcib3:   prefetched decode 0xf0000000-0xf7ffffff
pci3: <PCI bus> on pcib3
pci3: physical bus=3
found-> vendor=0x8086, dev=0xb154, revid=0x00
        bus=3, slot=0, func=0
        class=06-04-00, hdrtype=0x01, mfdev=0
        cmdreg=0x0107, statreg=0x0290, cachelnsz=0 (dwords)
        lattimer=0x20 (960 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns)
        map[10]: type 4, range 32, base 0000fc00, size  8, enabled
pcib3: device (null) requested decoded I/O range 0xfc00-0xfcff
        map[14]: type 1, range 32, base fe8ff000, size 12, enabled
pcib3: device (null) requested decoded memory range 0xfe8ff000-0xfe8fffff
pcib3: slot 1 INTA routed to irq 17
found-> vendor=0x1077, dev=0x1216, revid=0x06
        bus=3, slot=1, func=0
        class=01-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0117, statreg=0x02b0, cachelnsz=8 (dwords)
        lattimer=0x20 (960 ns), mingnt=0x40 (16000 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=17
        powerspec 1  supports D0 D3  current D0
pcib4: <MPTable PCI-PCI bridge> at device 0.0 on pci3
pcib4:   secondary bus     4
pcib4:   subordinate bus   4
pcib4:   I/O decode        0xf000-0xfff
pcib4:   memory decode     0xfea00000-0xfeafffff
pcib4:   prefetched decode 0xf0000000-0xf7ffffff
pci4: <PCI bus> on pcib4
pci4: physical bus=4
        map[10]: type 3, range 32, base f0000000, size 27, enabled
pcib4: device (null) requested decoded memory range 0xf0000000-0xf7ffffff
pcib3: device (null) requested decoded memory range 0xf0000000-0xf7ffffff
pcib4: slot 0 INTA routed to irq 16
found-> vendor=0x101e, dev=0x1960, revid=0x20
        bus=4, slot=0, func=0
        class=01-04-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0116, statreg=0x0290, cachelnsz=8 (dwords)
        lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=16
        powerspec 2  supports D0 D3  current D0
amr0: <LSILogic MegaRAID 1.51> mem 0xf0000000-0xf7ffffff irq 16 at device 0.0 on pci4
amr0: Reserved 0x8000000 bytes for rid 0x10 type 3 at 0xf0000000
amr0: [MPSAFE]
amr0: <LSILogic PERC 3/DC> Firmware 161J, BIOS 3.17, 128MB RAM
pci3: <mass storage, SCSI> at device 1.0 (no driver attached)
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
ahc_isa_probe 13: ioport 0xdc00 alloc failed
ahc_isa_probe 14: ioport 0xec00 alloc failed
pnpbios: 16 devices, largest 179 bytes
PNP0c02: adding fixed memory32 range 0-0x9ffff, size=0xa0000
PNP0c02: adding fixed memory32 range 0x100000-0x7fffffff, size=0x7ff00000
PNP0c02: adding fixed memory32 range 0xff000000-0xffffffff, size=0x1000000
PNP0c02: adding fixed memory32 range 0xf0000-0xfffff, size=0x10000
PNP0c02: adding io range 0x800-0x83f, size=0x40, align=0x1
PNP0c02: adding io range 0x850-0x85f, size=0x10, align=0x1
PNP0c02: adding io range 0xe0-0xef, size=0x10, align=0x1
PNP0c02: adding io range 0x2c00-0x2c7f, size=0x80, align=0x1
PNP0c02: adding irq mask 0x8000
pnpbios: handle 0 device ID PNP0c02 (020cd041)
PNP0501: adding irq mask 0x10
PNP0501: adding io range 0x3f8-0x3ff, size=0x8, align=0x8
pnpbios: handle 1 device ID PNP0501 (0105d041)
PNP0501: adding irq mask 0x8
PNP0501: adding io range 0x2f8-0x2ff, size=0x8, align=0x8
pnpbios: handle 2 device ID PNP0501 (0105d041)
pnpbios: handle 3 device ID PNP0401 (0104d041)
PNP0700: adding irq mask 0x40
PNP0700: adding io range 0x3f0-0x3f5, size=0x6, align=0x8
PNP0700: adding dma mask 0x4
pnpbios: handle 4 device ID PNP0700 (0007d041)
PNP0f13: adding irq mask 0x1000
pnpbios: handle 5 device ID PNP0f13 (130fd041)
PNP0a03: adding io range 0xcf8-0xcff, size=0x8, align=0x1
pnpbios: handle 6 device ID PNP0a03 (030ad041)
PNP0c02: adding irq mask 0x200
pnpbios: handle 7 device ID PNP0c02 (020cd041)
PNP0100: adding irq mask 0x1
PNP0100: adding io range 0x40-0x5f, size=0x20, align=0x1
pnpbios: handle 10 device ID PNP0100 (0001d041)
PNP0200: adding io range 0x80-0x9f, size=0x20, align=0x1
PNP0200: adding io range 0-0x1f, size=0x20, align=0x1
PNP0200: adding io range 0xc0-0xdf, size=0x20, align=0x1
PNP0200: adding dma mask 0x10
pnpbios: handle 11 device ID PNP0200 (0002d041)
PNP0303: adding irq mask 0x2
PNP0303: adding io range 0x60-0x60, size=0x1, align=0x1
PNP0303: adding io range 0x64-0x64, size=0x1, align=0x1
pnpbios: handle 12 device ID PNP0303 (0303d041)
PNP0800: adding io range 0x61-0x61, size=0x1, align=0x1
pnpbios: handle 13 device ID PNP0800 (0008d041)
PNP0b00: adding irq mask 0x100
PNP0b00: adding io range 0x70-0x7f, size=0x10, align=0x1
pnpbios: handle 14 device ID PNP0b00 (000bd041)
PNP0c04: adding irq mask 0x2000
PNP0c04: adding io range 0xf0-0xff, size=0x10, align=0x1
pnpbios: handle 15 device ID PNP0c04 (040cd041)
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <ISA Option ROMs> at iomem 0xc8000-0xc8fff,0xc0000-0xc7fff on isa0
pmtimer0 on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
ata0 failed to probe at port 0x1f0 irq 14 on isa0
ata1 failed to probe at port 0x170 irq 15 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
atkbd0: [GIANT-LOCKED]
psm0: current command byte:0065
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:00fe
kbdc: RESET_AUX return code:00fe
kbdc: RESET_AUX return code:00fe
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
psm0: failed to reset the aux device.
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fdc0: ic_type 90 part_id 73
fdc0: <Enhanced floppy controller> at port 0x3f0-0x3f5 irq 6 drq 2 on isa0
fdc0: ic_type 90 part_id 73
fdc0: [MPSAFE]
fdc0: [FAST]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
fe0: not probed (disabled)
ie0: not probed (disabled)
lnc0: not probed (disabled)
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
ppc0: parallel port not found.
ppc0: <Parallel port> failed to probe at irq 7 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio0: irq maps: 0x2001 0x2011 0x2001 0x2001
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81 
bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96 
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff 
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff 
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff 
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
unknown: <PNP0c02> can't assign resources (port)
unknown: <PNP0c02> at port 0x850-0x85f,0x800-0x83f iomem 0xf0000-0xfffff,0xff000000-0xffffffff,0x100000-0x7fffffff,0-0x9ffff on isa0
unknown: <PNP0501> can't assign resources (port)
unknown: <PNP0501> at port 0x3f8-0x3ff on isa0
adv1: Invalid baseport of 0x2f8 specified. Nearest valid baseport is 0x330.  Failing probe.
sio1: irq maps: 0x2001 0x2009 0x2001 0x2001
sio1: <16550A-compatible COM port> at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc1: parallel port not found.
unknown: <ECP parallel printer port> failed to probe on isa0
unknown: <PNP0700> can't assign resources (port)
unknown: <PNP0700> at port 0x3f0-0x3f5 on isa0
psmcpnp0: <PS/2 mouse port> at irq 12 on isa0
psm0: current command byte:0065
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:00fe
kbdc: RESET_AUX return code:00fe
kbdc: RESET_AUX return code:00fe
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
psm0: failed to reset the aux device.
adv1: Invalid baseport of 0xcf8 specified. Nearest valid baseport is 0x330.  Failing probe.
adv1: Invalid baseport of 0x40 specified. Nearest valid baseport is 0x100.  Failing probe.
adv1: Invalid baseport of 0x80 specified. Nearest valid baseport is 0x100.  Failing probe.
unknown: <PNP0303> can't assign resources (port)
unknown: <PNP0303> at port 0x60 on isa0
adv1: Invalid baseport of 0x61 specified. Nearest valid baseport is 0x100.  Failing probe.
unknown: <PNP0800> failed to probe at port 0x61 on isa0
adv1: Invalid baseport of 0x70 specified. Nearest valid baseport is 0x100.  Failing probe.
adv1: Invalid baseport of 0xf0 specified. Nearest valid baseport is 0x100.  Failing probe.
Device configuration finished.
Reducing kern.maxvnodes 134373 -> 100000
procfs registered
Timecounter "TSC" frequency 500019728 Hz quality -100
Timecounters tick every 10.000 msec
lo0: bpf attached
amrd0: <LSILogic MegaRAID logical drive> on amr0
amrd0: 34556MB (70770688 sectors) RAID 5 (optimal)
GEOM: new disk amrd0
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:70766262
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure amrd0s1, start 32256 length 36232326144 end 36232358399
GEOM: Configure amrd0s1a, start 0 length 524288000 end 524287999
GEOM: Configure amrd0s1b, start 524288000 length 4294967296 end 4819255295
GEOM: Configure amrd0s1c, start 0 length 36232326144 end 36232326143
GEOM: Configure amrd0s1d, start 4819255296 length 5368709120 end 10187964415
GEOM: Configure amrd0s1e, start 10187964416 length 1073741824 end 11261706239
GEOM: Configure amrd0s1f, start 11261706240 length 24970619904 end 36232326143
[0] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:80 typ:165 s(CHS):0/0/1 e(CHS):1023/254/63 s:0 l:50000
[0] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:80 typ:165 s(CHS):0/0/1 e(CHS):1023/254/63 s:0 l:50000
(probe5:amr0:0:5:0): error 22
(probe5:amr0:0:5:0): Unretryable Error
(probe0:amr0:0:0:0): error 22
(probe0:amr0:0:0:0): Unretryable Error
(probe15:amr0:1:0:0): error 22
(probe15:amr0:1:0:0): Unretryable Error
(probe16:amr0:1:1:0): error 22
(probe16:amr0:1:1:0): Unretryable Error
(probe7:amr0:0:8:0): error 22
(probe7:amr0:0:8:0): Unretryable Error
(probe17:amr0:1:2:0): error 22
(probe17:amr0:1:2:0): Unretryable Error
(probe8:amr0:0:9:0): error 22
(probe8:amr0:0:9:0): Unretryable Error
(probe23:amr0:1:9:0): error 22
(probe23:amr0:1:9:0): Unretryable Error
(probe9:amr0:0:10:0): error 22
(probe9:amr0:0:10:0): Unretryable Error
(probe24:amr0:1:10:0): error 22
(probe24:amr0:1:10:0): Unretryable Error
(probe10:amr0:0:11:0): error 22
(probe10:amr0:0:11:0): Unretryable Error
(probe25:amr0:1:11:0): error 22
(probe25:amr0:1:11:0): Unretryable Error
(probe11:amr0:0:12:0): error 22
(probe11:amr0:0:12:0): Unretryable Error
(probe18:amr0:1:3:0): error 22
(probe18:amr0:1:3:0): Unretryable Error
(probe12:amr0:0:13:0): error 22
(probe12:amr0:0:13:0): Unretryable Error
(probe19:amr0:1:4:0): error 22
(probe19:amr0:1:4:0): Unretryable Error
(probe13:amr0:0:14:0): error 22
(probe13:amr0:0:14:0): Unretryable Error
(probe20:amr0:1:5:0): error 22
(probe20:amr0:1:5:0): Unretryable Error
(probe14:amr0:0:15:0): error 22
(probe14:amr0:0:15:0): Unretryable Error
(probe21:amr0:1:6:0): error 22
(probe21:amr0:1:6:0): Unretryable Error
(probe3:amr0:0:3:0): error 22
(probe3:amr0:0:3:0): Unretryable Error
(probe2:amr0:0:2:0): error 22
(probe2:amr0:0:2:0): Unretryable Error
(probe1:amr0:0:1:0): error 22
(probe1:amr0:0:1:0): Unretryable Error
(probe22:amr0:1:8:0): error 22
(probe22:amr0:1:8:0): Unretryable Error
(probe4:amr0:0:4:0): error 22
(probe4:amr0:0:4:0): Unretryable Error
(probe26:amr0:1:12:0): error 22
(probe26:amr0:1:12:0): Unretryable Error
(probe6:amr0:0:6:0): error 22
(probe6:amr0:0:6:0): Unretryable Error
(probe27:amr0:1:13:0): error 22
(probe27:amr0:1:13:0): Unretryable Error
(probe28:amr0:1:14:0): error 22
(probe28:amr0:1:14:0): Unretryable Error
(probe29:amr0:1:15:0): error 22
(probe29:amr0:1:15:0): Unretryable Error
ses0 at amr0 bus 0 target 6 lun 0
ses0: <DELL 1x3 U2W SCSI BP 5.12> Fixed Processor SCSI-2 device 
ses0: SAF-TE Compliant Device
pass0 at amr0 bus 0 target 6 lun 0
pass0: <DELL 1x3 U2W SCSI BP 5.12> Fixed Processor SCSI-2 device 
SMP: AP CPU #1 Launched!
cpu1 AP:
     ID: 0x00000000   VER: 0x00040011 LDR: 0x01000000 DFR: 0x0fffffff
  lint0: 0x00010700 lint1: 0x00010400 TPR: 0x00000000 SVR: 0x000001ff
SMP: AP CPU #2 Launched!
cpu2 AP:
     ID: 0x01000000   VER: 0x00040011 LDR: 0x02000000 DFR: 0x0fffffff
  lint0: 0x00010700 lint1: 0x00010400 TPR: 0x00000000 SVR: 0x000001ff
SMP: AP CPU #3 Launched!
cpu3 AP:
     ID: 0x02000000   VER: 0x00040011 LDR: 0x04000000 DFR: 0x0fffffff
  lint0: 0x00010700 lint1: 0x00010400 TPR: 0x00000000 SVR: 0x000001ff
ioapic0: routing intpin 1 (ISA IRQ 1) to cluster 0
ioapic0: routing intpin 3 (ISA IRQ 3) to cluster 0
ioapic0: routing intpin 4 (ISA IRQ 4) to cluster 0
ioapic0: routing intpin 6 (ISA IRQ 6) to cluster 0
ioapic0: routing intpin 8 (ISA IRQ 8) to cluster 0
ioapic0: routing intpin 13 (ISA IRQ 13) to cluster 0
ioapic0: routing intpin 16 (PCI IRQ 16) to cluster 0
ioapic0: routing intpin 18 (PCI IRQ 18) to cluster 0
Mounting root from ufs:/dev/amrd0s1a
start_init: trying /sbin/init
Pre-seeding PRNG: kickstart.
Loading configuration files.
Entropy harvesting: interrupts ethernet point_to_point kickstart.
swapon: adding /dev/amrd0s1b as swap device
Starting file system checks:
/dev/amrd0s1a: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/amrd0s1a: clean, 218640 free (656 frags, 27248 blocks, 0.3% fragmentation)
/dev/amrd0s1e: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/amrd0s1e: clean, 506481 free (49 frags, 63304 blocks, 0.0% fragmentation)
/dev/amrd0s1f: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/amrd0s1f: clean, 11219339 free (36099 frags, 1397905 blocks, 0.3% fragmentation)
/dev/amrd0s1d: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/amrd0s1d: clean, 2528790 free (390 frags, 316050 blocks, 0.0% fragmentation)
Setting hostname: hippo.sentex.ca.
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
        inet 127.0.0.1 netmask 0xff000000 
        inet6 ::1 prefixlen 128 
        inet6 fe80::1%lo0 prefixlen 64 scopeid 0x2 
Starting dhclient.
em0: Link is up 1000 Mbps Full Duplex
em0: Link is up 1000 Mbps Full Duplex
em0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
        options=b<RXCSUM,TXCSUM,VLAN_MTU>
        inet6 fe80::20e:cff:fe5d:f8ca%em0 prefixlen 64 scopeid 0x1 
        inet 192.168.5.107 netmask 0xffffff00 broadcast 192.168.5.255
        ether 00:0e:0c:5d:f8:ca
        media: Ethernet autoselect
        status: no carrier
Additional routing options: IP gateway=YES.
Starting devd.
Mounting NFS file systems:.
Starting syslogd.
ELF ldconfig path: /lib /usr/lib /usr/lib/compat /usr/X11R6/lib /usr/local/lib
a.out ldconfig path: /usr/lib/aout /usr/lib/compat/aout /usr/X11R6/lib/aout
Recovering vi editor sessions:em0: Link is up 1000 Mbps Full Duplex
.
Starting local daemons:.
Updating motd.
Configuring syscons: blanktime.
Starting sshd.
Initial i386 initialization:.
Additional ABI support:.
Starting cron.
Local package initialization:.
Additional TCP options:.

Fri Jul  8 15:20:44 EDT 2005

FreeBSD/i386 (hippo.sentex.ca) (ttyd0)

login: root

--=====================_1996631594==_
Content-Type: text/plain; charset="us-ascii"
Content-Disposition: attachment; filename="6-acpi-apic.txt"

OK load /boot/mike/kernel
/boot/mike/kernel text=0x1fbfc0 data=0x2acd0+0x77394 syms=[0x4+0x320a0+0x4+0x3eb23]
OK set hint.ata.0="disabled"
OK set hint.ata.1="disabled"
OK boot -v
/boot/kernel/acpi.ko text=0x41e40 data=0x20e0+0x10b0 syms=[0x4+0x7740+0x4+0x9ead]
GDB: no debug ports present
KDB: debugger backends: ddb
KDB: current backend: ddb
SMAP type=01 base=0000000000000000 len=00000000000a0000
SMAP type=01 base=0000000000100000 len=000000007fefe000
SMAP type=02 base=000000007fffe000 len=0000000000002000
SMAP type=02 base=00000000fec00000 len=0000000000010000
SMAP type=02 base=00000000fee00000 len=0000000000010000
SMAP type=02 base=00000000fff80000 len=0000000000080000
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 6.0-CURRENT #1: Wed Jul  6 11:48:02 EDT 2005
    mdtancsa@freebsd-current.sentex.ca:/usr/src/sys/i386/compile/mike
WARNING: WITNESS option enabled, expect reduced performance.
Preloaded elf kernel "/boot/mike/kernel" at 0xc0769000.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc0769158.
MP Configuration Table version 1.4 found at 0xc00f0000
Table 'FACP' at 0xfdf20
Table 'APIC' at 0xfdf94
MADT: Found table at 0xfdf94
APIC: Using the MADT enumerator.
MADT: Found CPU APIC ID 3 ACPI ID 1: enabled
SMP: Added CPU 3 (AP)
MADT: Found CPU APIC ID 2 ACPI ID 2: enabled
SMP: Added CPU 2 (AP)
MADT: Found CPU APIC ID 1 ACPI ID 3: enabled
SMP: Added CPU 1 (AP)
MADT: Found CPU APIC ID 0 ACPI ID 4: enabled
SMP: Added CPU 0 (AP)
ACPI APIC Table: <DELL   PE6350  >
Calibrating clock(s) ... i8254 clock: 1193231 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 500019444 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (500.02-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x672  Stepping = 2
  Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory  = 2147475456 (2047 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000000828000 - 0x000000007dbc5fff, 2100944896 bytes (512926 pages)
avail memory = 2100953088 (2003 MB)
APIC ID: physical 0, logical 0:0
APIC ID: physical 1, logical 0:1
APIC ID: physical 2, logical 0:2
APIC ID: physical 3, logical 0:3
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
 cpu0 (BSP): APIC ID:  3
 cpu1 (AP): APIC ID:  0
 cpu2 (AP): APIC ID:  1
 cpu3 (AP): APIC ID:  2
bios32: Found BIOS32 Service Directory header at 0xc00ffe80
bios32: Entry = 0xffe90 (c00ffe90)  Rev = 0  Len = 1
pcibios: PCI BIOS entry at 0xf0000+0xcc4e
pnpbios: Found PnP BIOS data at 0xc00fe2d0
pnpbios: Entry = f0000:e2f4  Rev = 1.0
Other BIOS signatures found:
APIC: CPU 0 has ACPI ID 1
APIC: CPU 1 has ACPI ID 4
APIC: CPU 2 has ACPI ID 3
APIC: CPU 3 has ACPI ID 2
MADT: Found IO APIC ID 4, Interrupt 0 at 0xfec00000
ioapic0: Changing APIC ID to 4
ioapic0: Routing external 8259A's -> intpin 0
ioapic0: intpin 0 -> ExtINT (edge, high)
ioapic0: intpin 1 -> ISA IRQ 1 (edge, high)
ioapic0: intpin 2 -> ISA IRQ 2 (edge, high)
ioapic0: intpin 3 -> ISA IRQ 3 (edge, high)
ioapic0: intpin 4 -> ISA IRQ 4 (edge, high)
ioapic0: intpin 5 -> ISA IRQ 5 (edge, high)
ioapic0: intpin 6 -> ISA IRQ 6 (edge, high)
ioapic0: intpin 7 -> ISA IRQ 7 (edge, high)
ioapic0: intpin 8 -> ISA IRQ 8 (edge, high)
ioapic0: intpin 9 -> ISA IRQ 9 (edge, high)
ioapic0: intpin 10 -> ISA IRQ 10 (edge, high)
ioapic0: intpin 11 -> ISA IRQ 11 (edge, high)
ioapic0: intpin 12 -> ISA IRQ 12 (edge, high)
ioapic0: intpin 13 -> ISA IRQ 13 (edge, high)
ioapic0: intpin 14 -> ISA IRQ 14 (edge, high)
ioapic0: intpin 15 -> ISA IRQ 15 (edge, high)
ioapic0: intpin 16 -> PCI IRQ 16 (level, low)
ioapic0: intpin 17 -> PCI IRQ 17 (level, low)
ioapic0: intpin 18 -> PCI IRQ 18 (level, low)
ioapic0: intpin 19 -> PCI IRQ 19 (level, low)
ioapic0: intpin 20 -> PCI IRQ 20 (level, low)
ioapic0: intpin 21 -> PCI IRQ 21 (level, low)
ioapic0: intpin 22 -> PCI IRQ 22 (level, low)
ioapic0: intpin 23 -> PCI IRQ 23 (level, low)
MADT: Interrupt override: source 0, irq 2
ioapic0: Routing IRQ 0 -> intpin 2
ioapic0: intpin 2 trigger: edge
ioapic0: intpin 2 polarity: high
MADT: Interrupt override: source 9, irq 9
ioapic0: intpin 9 trigger: level
ioapic0: intpin 9 polarity: high
ioapic0 <Version 1.1> irqs 0-23 on motherboard
cpu0 BSP:
     ID: 0x03000000   VER: 0x00040011 LDR: 0x08000000 DFR: 0x0fffffff
  lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
  timer: 0x000100ef therm: 0x00000000 err: 0x00010000 pcm: 0x00010000
random: <entropy source, Software, Yarrow>
mem: <memory>
Pentium Pro MTRR support enabled
null: <null device, zero device>
io: <I/O>
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <DELL PE6350> on motherboard
acpi0: [MPSAFE]
pci_open(1):    mode 1 addr port (0x0cf8) is 0x80008070
pci_open(1a):   mode1res=0x80000000 (0x80000000)
pci_cfgcheck:   device 0 1 2 [class=060100] [hdr=80] is there (id=71108086)
pcibios: BIOS version 2.10
Found $PIR table, 11 entries at 0xc00fc7a0
PCI-Only Interrupts: none
Location  Bus Device Pin  Link  IRQs
embedded    0    2    A   0x64  14
embedded    0    2    B   0x65  15
embedded    0    2    D   0x63  3 4 5 6 7 10 11 12 14
embedded    1    4    A   0x65  3 4 5 6 7 10 11 12 14
embedded    1    6    A   0x66  3 4 5 6 7 10 11 12 14
embedded    1    8    A   0x64  3 4 5 6 7 10 11 12 14
slot 1      0    6    A   0x69  3 4 5 6 7 10 11 12 14
slot 1      0    6    B   0x64  3 4 5 6 7 10 11 12 14
slot 1      0    6    C   0x67  3 4 5 6 7 10 11 12 14
slot 1      0    6    D   0x68  3 4 5 6 7 10 11 12 14
slot 2      0    8    A   0x68  3 4 5 6 7 10 11 12 14
slot 2      0    8    B   0x69  3 4 5 6 7 10 11 12 14
slot 2      0    8    C   0x64  3 4 5 6 7 10 11 12 14
slot 2      0    8    D   0x67  3 4 5 6 7 10 11 12 14
slot 3      0   10    A   0x67  3 4 5 6 7 10 11 12 14
slot 3      0   10    B   0x68  3 4 5 6 7 10 11 12 14
slot 3      0   10    C   0x69  3 4 5 6 7 10 11 12 14
slot 3      0   10    D   0x64  3 4 5 6 7 10 11 12 14
slot 4      2    1    A   0x63  3 4 5 6 7 10 11 12 14
slot 4      2    1    B   0x60  3 4 5 6 7 10 11 12 14
slot 4      2    1    C   0x61  3 4 5 6 7 10 11 12 14
slot 4      2    1    D   0x62  3 4 5 6 7 10 11 12 14
slot 5      2    3    A   0x62  3 4 5 6 7 10 11 12 14
slot 5      2    3    B   0x63  3 4 5 6 7 10 11 12 14
slot 5      2    3    C   0x60  3 4 5 6 7 10 11 12 14
slot 5      2    3    D   0x61  3 4 5 6 7 10 11 12 14
slot 6      2    5    A   0x61  3 4 5 6 7 10 11 12 14
slot 6      2    5    B   0x62  3 4 5 6 7 10 11 12 14
slot 6      2    5    C   0x63  3 4 5 6 7 10 11 12 14
slot 6      2    5    D   0x60  3 4 5 6 7 10 11 12 14
slot 7      2    7    A   0x60  3 4 5 6 7 10 11 12 14
slot 7      2    7    B   0x61  3 4 5 6 7 10 11 12 14
slot 7      2    7    C   0x62  3 4 5 6 7 10 11 12 14
slot 7      2    7    D   0x63  3 4 5 6 7 10 11 12 14
AcpiOsDerivePciId: bus 0 dev 2 func 1
AcpiOsDerivePciId: bus 0 dev 2 func 2
AcpiOsDerivePciId: bus 0 dev 6 func 0
AcpiOsDerivePciId: bus 0 dev 6 func 1
AcpiOsDerivePciId: bus 0 dev 6 func 2
AcpiOsDerivePciId: bus 0 dev 6 func 3
AcpiOsDerivePciId: bus 0 dev 6 func 4
AcpiOsDerivePciId: bus 0 dev 6 func 5
AcpiOsDerivePciId: bus 0 dev 6 func 6
AcpiOsDerivePciId: bus 0 dev 6 func 7
AcpiOsDerivePciId: bus 0 dev 8 func 0
AcpiOsDerivePciId: bus 0 dev 8 func 1
AcpiOsDerivePciId: bus 0 dev 8 func 2
AcpiOsDerivePciId: bus 0 dev 8 func 3
AcpiOsDerivePciId: bus 0 dev 8 func 4
AcpiOsDerivePciId: bus 0 dev 8 func 5
AcpiOsDerivePciId: bus 0 dev 8 func 6
AcpiOsDerivePciId: bus 0 dev 8 func 7
AcpiOsDerivePciId: bus 0 dev 10 func 0
AcpiOsDerivePciId: bus 0 dev 10 func 1
AcpiOsDerivePciId: bus 0 dev 10 func 2
AcpiOsDerivePciId: bus 0 dev 10 func 3
AcpiOsDerivePciId: bus 0 dev 10 func 4
AcpiOsDerivePciId: bus 0 dev 10 func 5
AcpiOsDerivePciId: bus 0 dev 10 func 6
AcpiOsDerivePciId: bus 0 dev 10 func 7
AcpiOsDerivePciId: bus 2 dev 1 func 0
AcpiOsDerivePciId: bus 2 dev 1 func 1
AcpiOsDerivePciId: bus 2 dev 1 func 2
AcpiOsDerivePciId: bus 2 dev 1 func 3
AcpiOsDerivePciId: bus 2 dev 1 func 4
AcpiOsDerivePciId: bus 2 dev 1 func 5
AcpiOsDerivePciId: bus 2 dev 1 func 6
AcpiOsDerivePciId: bus 2 dev 1 func 7
AcpiOsDerivePciId: bus 2 dev 3 func 0
AcpiOsDerivePciId: bus 2 dev 3 func 1
AcpiOsDerivePciId: bus 2 dev 3 func 2
AcpiOsDerivePciId: bus 2 dev 3 func 3
AcpiOsDerivePciId: bus 2 dev 3 func 4
AcpiOsDerivePciId: bus 2 dev 3 func 5
AcpiOsDerivePciId: bus 2 dev 3 func 6
AcpiOsDerivePciId: bus 2 dev 3 func 7
AcpiOsDerivePciId: bus 2 dev 5 func 0
AcpiOsDerivePciId: bus 2 dev 5 func 1
AcpiOsDerivePciId: bus 2 dev 5 func 2
AcpiOsDerivePciId: bus 2 dev 5 func 3
AcpiOsDerivePciId: bus 2 dev 5 func 4
AcpiOsDerivePciId: bus 2 dev 5 func 5
AcpiOsDerivePciId: bus 2 dev 5 func 6
AcpiOsDerivePciId: bus 2 dev 5 func 7
AcpiOsDerivePciId: bus 2 dev 7 func 0
AcpiOsDerivePciId: bus 2 dev 7 func 1
AcpiOsDerivePciId: bus 2 dev 7 func 2
AcpiOsDerivePciId: bus 2 dev 7 func 3
AcpiOsDerivePciId: bus 2 dev 7 func 4
AcpiOsDerivePciId: bus 2 dev 7 func 5
AcpiOsDerivePciId: bus 2 dev 7 func 6
AcpiOsDerivePciId: bus 2 dev 7 func 7
AcpiOsDerivePciId: bus 0 dev 2 func 0
acpi0: Power Button (fixed)
pci_link0: <ACPI PCI Link LNK0> irq 10 on acpi0
pci_link0: Links after initial probe:
Index  IRQ  Rtd  Ref  IRQs
    0   10   N     0  3 4 5 6 7 9 10 11 12 14
pci_link0: Links after initial validation:
Index  IRQ  Rtd  Ref  IRQs
    0   10   N     0  3 4 5 6 7 9 10 11 12 14
pci_link0: Links after disable:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11 12 14
pci_link1: <ACPI PCI Link LNK1> irq 11 on acpi0
pci_link1: Links after initial probe:
Index  IRQ  Rtd  Ref  IRQs
    0   11   N     0  3 4 5 6 7 9 10 11 12 14
pci_link1: Links after initial validation:
Index  IRQ  Rtd  Ref  IRQs
    0   11   N     0  3 4 5 6 7 9 10 11 12 14
pci_link1: Links after disable:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11 12 14
pci_link2: <ACPI PCI Link LNK2> irq 14 on acpi0
pci_link2: Links after initial probe:
Index  IRQ  Rtd  Ref  IRQs
    0   14   N     0  3 4 5 6 7 9 10 11 12 14
pci_link2: Links after initial validation:
Index  IRQ  Rtd  Ref  IRQs
    0   14   N     0  3 4 5 6 7 9 10 11 12 14
pci_link2: Links after disable:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11 12 14
pci_link3: <ACPI PCI Link LNK3> on acpi0
pci_link3: Links after initial probe:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11 12 14
pci_link3: Links after initial validation:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11 12 14
pci_link3: Links after disable:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11 12 14
pci_link4: <ACPI PCI Link LNK4> on acpi0
pci_link4: Links after initial probe:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11 12 14
pci_link4: Links after initial validation:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11 12 14
pci_link4: Links after disable:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11 12 14
pci_link5: <ACPI PCI Link LNK5> on acpi0
pci_link5: Links after initial probe:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11 12 14
pci_link5: Links after initial validation:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11 12 14
pci_link5: Links after disable:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11 12 14
pci_link6: <ACPI PCI Link LNK6> on acpi0
pci_link6: Links after initial probe:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11 12 14
pci_link6: Links after initial validation:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11 12 14
pci_link6: Links after disable:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11 12 14
pci_link7: <ACPI PCI Link LNK7> on acpi0
pci_link7: Links after initial probe:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11 12 14
pci_link7: Links after initial validation:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11 12 14
pci_link7: Links after disable:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11 12 14
pci_link8: <ACPI PCI Link LNK8> on acpi0
pci_link8: Links after initial probe:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11 12 14
pci_link8: Links after initial validation:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11 12 14
pci_link8: Links after disable:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11 12 14
pci_link9: <ACPI PCI Link LNK9> on acpi0
pci_link9: Links after initial probe:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11 12 14
pci_link9: Links after initial validation:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11 12 14
pci_link9: Links after disable:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11 12 14
ACPI timer: 0/3 0/5 0/16777209 0/3 0/3 0/5 0/16777214 0/16776961 0/4 0/4 -> 0
Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
cpu2: <ACPI CPU> on acpi0
cpu3: <ACPI CPU> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
found-> vendor=0x8086, dev=0x7110, revid=0x02
        bus=0, slot=2, func=0
        class=06-01-00, hdrtype=0x00, mfdev=1
        cmdreg=0x000f, statreg=0x0280, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x7111, revid=0x01
        bus=0, slot=2, func=1
        class=01-01-80, hdrtype=0x00, mfdev=0
        cmdreg=0x0000, statreg=0x0280, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        map[20]: type 4, range 32, base 00000000, size  4, port disabled
found-> vendor=0x8086, dev=0x7112, revid=0x01
        bus=0, slot=2, func=2
        class=0c-03-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0000, statreg=0x0280, cachelnsz=0 (dwords)
        lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=d, irq=255
        map[20]: type 4, range 32, base 00000000, size  5, port disabled
found-> vendor=0x8086, dev=0x7113, revid=0x02
        bus=0, slot=2, func=3
        class=06-80-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        map[90]: type 4, range 32, base 00000850, size  4, enabled
found-> vendor=0x1002, dev=0x4749, revid=0x5c
        bus=0, slot=4, func=0
        class=03-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x00a7, statreg=0x0280, cachelnsz=8 (dwords)
        lattimer=0x20 (960 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
        map[10]: type 3, range 32, base ee000000, size 24, enabled
        map[14]: type 4, range 32, base 0000dc00, size  8, enabled
        map[18]: type 1, range 32, base eff00000, size 12, enabled
found-> vendor=0x8086, dev=0x84ca, revid=0x03
        bus=0, slot=16, func=0
        class=06-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x84cb, revid=0x02
        bus=0, slot=18, func=0
        class=06-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0116, statreg=0x2280, cachelnsz=8 (dwords)
        lattimer=0x48 (2160 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x84cb, revid=0x02
        bus=0, slot=19, func=0
        class=06-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0116, statreg=0x0280, cachelnsz=8 (dwords)
        lattimer=0x48 (2160 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x84cb, revid=0x02
        bus=0, slot=20, func=0
        class=06-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0116, statreg=0x2280, cachelnsz=8 (dwords)
        lattimer=0x48 (2160 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
isab0: <PCI-ISA bridge> at device 2.0 on pci0
isa0: <ISA bus> on isab0
pci0: <mass storage, ATA> at device 2.1 (no driver attached)
pci0: <serial bus, USB> at device 2.2 (no driver attached)
pci0: <bridge> at device 2.3 (no driver attached)
pci0: <display, VGA> at device 4.0 (no driver attached)
pcib1: <ACPI Host-PCI bridge> on acpi0
pci1: <ACPI PCI bus> on pcib1
pci1: physical bus=1
pcib2: <ACPI Host-PCI bridge> on acpi0
pci2: <ACPI PCI bus> on pcib2
pci2: physical bus=2
found-> vendor=0x8086, dev=0x1076, revid=0x00
        bus=2, slot=3, func=0
        class=02-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0117, statreg=0x0230, cachelnsz=8 (dwords)
        lattimer=0x20 (960 ns), mingnt=0xff (63750 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=14
        powerspec 2  supports D0 D3  current D0
        MSI supports 1 message, 64 bit
        map[10]: type 1, range 32, base feb20000, size 17, enabled
        map[14]: type 1, range 32, base feb00000, size 17, enabled
        map[18]: type 4, range 32, base 0000ecc0, size  6, enabled
pcib2: matched entry for 2.3.INTA
pcib2: slot 3 INTA hardwired to IRQ 18
found-> vendor=0x8086, dev=0xb154, revid=0x00
        bus=2, slot=7, func=0
        class=06-04-00, hdrtype=0x01, mfdev=0
        cmdreg=0x0107, statreg=0x02b0, cachelnsz=0 (dwords)
        lattimer=0x20 (960 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns)
pci2: <network, ethernet> at device 3.0 (no driver attached)
pci2:3:0: Transition from D0 to D3
pcib3: <ACPI PCI-PCI bridge> at device 7.0 on pci2
pcib3:   secondary bus     3
pcib3:   subordinate bus   4
pcib3:   I/O decode        0xf000-0xffff
pcib3:   memory decode     0xfe800000-0xfeafffff
pcib3:   prefetched decode 0xf0000000-0xf7ffffff
pcib3: could not get PCI interrupt routing table for \_SB_.PX1A.SL70 - AE_NOT_FOUND
pci3: <ACPI PCI bus> on pcib3
pci3: physical bus=3
found-> vendor=0x8086, dev=0xb154, revid=0x00
        bus=3, slot=0, func=0
        class=06-04-00, hdrtype=0x01, mfdev=0
        cmdreg=0x0107, statreg=0x0290, cachelnsz=0 (dwords)
        lattimer=0x20 (960 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1077, dev=0x1216, revid=0x06
        bus=3, slot=1, func=0
        class=01-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0117, statreg=0x02b0, cachelnsz=8 (dwords)
        lattimer=0x20 (960 ns), mingnt=0x40 (16000 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=11
        powerspec 1  supports D0 D3  current D0
        map[10]: type 4, range 32, base 0000fc00, size  8, enabled
pcib3: (null) requested I/O range 0xfc00-0xfcff: in range
        map[14]: type 1, range 32, base fe8ff000, size 12, enabled
pcib3: (null) requested memory range 0xfe8ff000-0xfe8fffff: good
pcib2: matched entry for 2.7.INTB
pcib2: slot 7 INTB hardwired to IRQ 17
pcib3: slot 1 INTA is routed to irq 17
pcib4: <PCI-PCI bridge> at device 0.0 on pci3
pcib4:   secondary bus     4
pcib4:   subordinate bus   4
pcib4:   I/O decode        0xf000-0xfff
pcib4:   memory decode     0xfea00000-0xfeafffff
pcib4:   prefetched decode 0xf0000000-0xf7ffffff
pci4: <PCI bus> on pcib4
pci4: physical bus=4
found-> vendor=0x101e, dev=0x1960, revid=0x20
        bus=4, slot=0, func=0
        class=01-04-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0116, statreg=0x0290, cachelnsz=8 (dwords)
        lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=10
        powerspec 2  supports D0 D3  current D0
        map[10]: type 3, range 32, base f0000000, size 27, enabled
pcib4: (null) requested memory range 0xf0000000-0xf7ffffff: good
pcib3: (null) requested memory range 0xf0000000-0xf7ffffff: good
pcib2: matched entry for 2.7.INTA
pcib2: slot 7 INTA hardwired to IRQ 16
pcib3: slot 0 INTA is routed to irq 16
pcib4: slot 0 INTA is routed to irq 16
amr0: <LSILogic MegaRAID 1.51> mem 0xf0000000-0xf7ffffff irq 16 at device 0.0 on pci4
amr0: Reserved 0x8000000 bytes for rid 0x10 type 3 at 0xf0000000
amr0: [MPSAFE]
amr0: <LSILogic PERC 3/DC> Firmware 161J, BIOS 3.17, 128MB RAM
pci3: <mass storage, SCSI> at device 1.0 (no driver attached)
pci3:1:0: Transition from D0 to D3
fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: ic_type 90 part_id 73
fdc0: [MPSAFE]
fdc0: [FAST]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x1d0000
atkbd0: [GIANT-LOCKED]
psm0: unable to allocate IRQ
psmcpnp0: <PS/2 mouse port> irq 12 on acpi0
psm0: current command byte:0065
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:00fe
kbdc: RESET_AUX return code:00fe
kbdc: RESET_AUX return code:00fe
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
psm0: failed to reset the aux device.
sio0: irq maps: 0x2001 0x2011 0x2001 0x2001
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A, console
sio1: irq maps: 0x2001 0x2009 0x2001 0x2001
sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
ppc0: using extended I/O port range
ppc0: using extended I/O port range
atkbdc: atkbdc0 already exists; skipping it
fdc: fdc0 already exists; skipping it
sio: sio0 already exists; skipping it
sio: sio1 already exists; skipping it
pnp_identify: Trying Read_Port at 203
pnp_identify: Trying Read_Port at 243
pnp_identify: Trying Read_Port at 283
pnp_identify: Trying Read_Port at 2c3
pnp_identify: Trying Read_Port at 303
pnp_identify: Trying Read_Port at 343                                       
pnp_identify: Trying Read_Port at 383                                       
pnp_identify: Trying Read_Port at 3c3                                       
PNP Identify complete                                                       
sc: sc0 already exists; skipping it                                         
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <ISA Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xc8fff on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fe0: not probed (disabled)
ie0: not probed (disabled)
lnc0: not probed (disabled)
ppc0: parallel port not found.
ppc0: <Parallel port> failed to probe at irq 7 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x100>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
Device configuration finished.
Reducing kern.maxvnodes 134627 -> 100000
lapic: Divisor 2, Frequency 50001885 hz
Timecounter "TSC" frequency 500019444 Hz quality -100
Timecounters tick every 1.000 msec
lo0: bpf attached
amrd0: <LSILogic MegaRAID logical drive> on amr0
amrd0: 34556MB (70770688 sectors) RAID 5 (optimal)
GEOM: new disk amrd0
KDB: enter: Line break on console
[thread pid 14 tid 100002 ]
Stopped at      kdb_enter+0x2c: leave   
db> trace
Tracing pid 14 tid 100002 td 0xc309bc00
kdb_enter(c05f38bd,0,c31972c0,c3098b00,c308e490) at kdb_enter+0x2c
siointr1(c0686d20,8,c05f37d1,56e,e4ba7c7c) at siointr1+0x3be
siointr(c31a4000,c309bc00,4,0,c315a618) at siointr+0x21
intr_execute_handlers(c308e490,e4ba7c98,4,e4ba7cdc,c05a0ea3) at intr_execute_handlers+0xb1
lapic_handle_intr(34) at lapic_handle_intr+0x23
Xapic_isr1() at Xapic_isr1+0x33
--- interrupt, eip = 0xc07479c5, esp = 0xe4ba7cdc, ebp = 0xe4ba7cdc ---
acpi_cpu_c1(e4ba7cf4,c049e8d1,c0630e60,1,fffffffe) at acpi_cpu_c1+0x5
acpi_cpu_idle(c047bde8,c309a418,e4ba7d24,c047bbdd,0) at acpi_cpu_idle+0x13e
idle_proc(0,e4ba7d38,0,c047bde8,0) at idle_proc+0x65
fork_exit(c047bde8,0,e4ba7d38) at fork_exit+0x7d
fork_trampoline() at fork_trampoline+0x8
--- trap 0x1, eip = 0, esp = 0xe4ba7d6c, ebp = 0 ---
db> continue

--=====================_1996631594==_--




Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?6.2.1.2.0.20050708110446.07de5768>