Date: Tue, 12 Aug 2008 11:49:57 -0400 From: Mike Tancsa <mike@sentex.net> To: Andrew Hotlab <andrew.hotlab@hotmail.com> Cc: freebsd-hardware@freebsd.org Subject: RE: Areca ARC-1120 on FreeBSD 7.0 Message-ID: <200808121549.m7CFnmBo031979@lava.sentex.ca> In-Reply-To: <BAY102-W48FB2A48FD4E357A8A8A25F6700@phx.gbl> References: <BAY102-W428F28799636A3B28D3A56F6710@phx.gbl> <tcv2a45d6qg60em6mlgpbtrrm4sjndtgt6@4ax.com> <BAY102-W48FB2A48FD4E357A8A8A25F6700@phx.gbl>
next in thread | previous in thread | raw e-mail | index | archive | help
At 11:11 AM 8/12/2008, Andrew Hotlab wrote: >You can confirm me that you are successfully using FreeBSD 7.0R with >the 1.43 firmware? If it's so, we might compare our hardware >components to find out if and what are differences... Hi, The dmesg below is on a supermicro board. Actually, if you take the Areca out, does 7.0R boot up ? As mentioned by another poster, try the RELENG_7 snapshot to see if it boots with that. If you are starting fresh, I would suggest it as there are a number of bug fixes and enhancements in the snapshot and its quite stable. Copyright (c) 1992-2008 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 7.0-PRERELEASE #3: Wed Feb 13 11:51:23 EST 2008 mdtancsa@db.example.com:/usr/obj/usr/src/sys/db Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Intel(R) Xeon(R) CPU 3060 @ 2.40GHz (2400.10-MHz K8-class CPU) Origin = "GenuineIntel" Id = 0x6f6 Stepping = 6 Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> Features2=0xe3bd<SSE3,RSVD2,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM> AMD Features=0x20100800<SYSCALL,NX,LM> AMD Features2=0x1<LAHF> Cores per package: 2 usable memory = 8577662976 (8180 MB) avail memory = 8298295296 (7913 MB) ACPI APIC Table: <INTEL S3000AH> FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 ioapic0: Changing APIC ID to 5 ioapic0 <Version 2.0> irqs 0-23 on motherboard kbd1 at kbdmux0 acpi0: <INTEL S3000AH> on motherboard acpi0: [ITHREAD] acpi0: Power Button (fixed) Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0 cpu0: <ACPI CPU> on acpi0 est0: <Enhanced SpeedStep Frequency Control> on cpu0 est: CPU supports Enhanced Speedstep, but is not recognized. est: cpu_vendor GenuineIntel, msr 92a092a0600092a device_attach: est0 attach returned 6 p4tcc0: <CPU Frequency Thermal Control> on cpu0 cpu1: <ACPI CPU> on acpi0 est1: <Enhanced SpeedStep Frequency Control> on cpu1 est: CPU supports Enhanced Speedstep, but is not recognized. est: cpu_vendor GenuineIntel, msr 92a092a0600092a device_attach: est1 attach returned 6 p4tcc1: <CPU Frequency Thermal Control> on cpu1 acpi_button0: <Sleep Button> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 pcib1: <ACPI PCI-PCI bridge> at device 28.0 on pci0 pci1: <ACPI PCI bus> on pcib1 pcib2: <ACPI PCI-PCI bridge> at device 0.0 on pci1 pci2: <ACPI PCI bus> on pcib2 arcmsr0: <Areca SATA Host Adapter RAID Controller > mem 0xe8600000-0xe8600fff,0xe8000000-0xe83fffff irq 18 at device 14.0 on pci2 ARECA RAID ADAPTER0: Driver Version 1.20.00.15 2007-10-07 ARECA RAID ADAPTER0: FIRMWARE VERSION V1.43 2007-4-17 arcmsr0: [ITHREAD] pcib3: <PCI-PCI bridge> at device 0.2 on pci1 pci3: <PCI bus> on pcib3 pcib4: <ACPI PCI-PCI bridge> at device 28.4 on pci0 pci4: <ACPI PCI bus> on pcib4 pcib5: <ACPI PCI-PCI bridge> at device 28.5 on pci0 pci5: <ACPI PCI bus> on pcib5 em0: <Intel(R) PRO/1000 Network Connection Version - 6.7.3> port 0x2000-0x201f mem 0xe8580000-0xe859ffff,0xe8500000-0xe857ffff irq 17 at device 0.0 on pci5 em0: Using MSI interrupt em0: Ethernet address: 00:15:17:50:40:28 em0: [FILTER] pci5: <simple comms, UART> at device 0.3 (no driver attached) pci5: <serial bus> at device 0.4 (no driver attached) pcib6: <ACPI PCI-PCI bridge> at device 30.0 on pci0 pci6: <ACPI PCI bus> on pcib6 vgapci0: <VGA-compatible display> port 0x1000-0x10ff mem 0xe0000000-0xe7ffffff,0xe8440000-0xe844ffff irq 18 at device 4.0 on pci6 em1: <Intel(R) PRO/1000 Network Connection Version - 6.7.3> port 0x1100-0x113f mem 0xe8420000-0xe843ffff,0xe8400000-0xe841ffff irq 17 at device 5.0 on pci6 em1: Ethernet address: 00:15:17:50:40:29 em1: [FILTER] isab0: <PCI-ISA bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel ICH7 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x3030-0x303f irq 18 at device 31.1 on pci0 ata0: <ATA channel 0> on atapci0 ata0: [ITHREAD] ata1: <ATA channel 1> on atapci0 ata1: [ITHREAD] atapci1: <Intel ICH7 SATA300 controller> port 0x3048-0x304f,0x3064-0x3067,0x3040-0x3047,0x3060-0x3063,0x3020-0x302f mem 0xe8700000-0xe87003ff irq 19 at device 31.2 on pci0 atapci1: [ITHREAD] ata2: <ATA channel 0> on atapci1 ata2: [ITHREAD] ata3: <ATA channel 1> on atapci1 ata3: [ITHREAD] pci0: <serial bus, SMBus> at device 31.3 (no driver attached) fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f0 irq 6 drq 2 on acpi0 fdc0: [FILTER] atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0 at atkbd0 atkbd0: [GIANT-LOCKED] atkbd0: [ITHREAD] sio0: configured irq 4 not in bitmap of probed irqs 0 sio0: port may not be enabled sio0: configured irq 4 not in bitmap of probed irqs 0 sio0: port may not be enabled sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 sio0: type 16550A, console sio0: [FILTER] orm0: <ISA Option ROMs> at iomem 0xc0000-0xc8fff,0xc9000-0xc9fff,0xca000-0xcafff,0xcb000-0xcbfff on isa0 ppc0: cannot reserve I/O port range sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 Timecounters tick every 1.000 msec Waiting 5 seconds for SCSI devices to settle (probe16:arcmsr0:0:16:0): inquiry data fails comparison at DV1 step da0 at arcmsr0 bus 0 target 0 lun 0 da0: <Areca ARC-1210-VOL#00 R001> Fixed Direct Access SCSI-5 device da0: 166.666MB/s transfers (83.333MHz DT, offset 32, 16bit) da0: 305175MB (624999424 512 byte sectors: 255H 63S/T 38904C) SMP: AP CPU #1 Launched! Trying to mount root from ufs:/dev/da0s1a >Thanks a lot for your help. > >---------------------------------------- > > From: mike@sentex.net > > To: andrew.hotlab@hotmail.com > > Subject: Re: Areca ARC-1120 on FreeBSD 7.0 > > Date: Tue, 12 Aug 2008 08:13:56 -0400 > > > > On Mon, 11 Aug 2008 22:54:41 +0000, in sentex.lists.freebsd.hardware > > you wrote: > >>arcmsr0: mem 0xfc7ff000-0xfc7fffff,0xfc000000-0xfc3fffff irq 31 > at device 14.0 on pci2 > >>arcmsr0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfc7ff000 > >>ARECA RAID ADAPTER0: Driver Version 1.20.00.15 2007-10-07 > >>ARECA RAID ADAPTER0: FIRMWARE VERSION V1.39 2006-2-9 > > > > > > Not sure it will help you or not, but I run the same card with version > > 1.43 of the firmware. I would try to upgrade the Areca card's > > firmware and then give 7.0R another try. > > > > ---Mike > >_________________________________________________________________ >Invite your mail contacts to join your friends list with Windows >Live Spaces. It's easy! >http://spaces.live.com/spacesapi.aspx?wx_action=create&wx_url=/friends.aspx&mkt=en-us
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200808121549.m7CFnmBo031979>