Skip site navigation (1)Skip section navigation (2)
Date:      Wed, 02 Apr 2003 13:53:35 +0000
From:      Ryan Merrick <sandshrimp@attbi.com>
To:        David Olbersen <DOlbersen@stbernard.com>
Cc:        "freebsd-questions \(E-mail\)" <freebsd-questions@freebsd.org>
Subject:   Re: Help with IDE RAID
Message-ID:  <3E8AEB5F.7080104@attbi.com>
References:  <E7E213858379814A9AE48CA6754F5ECB0D6CAA@mail01.stbernard.com>

next in thread | previous in thread | raw e-mail | index | archive | help
David Olbersen wrote:

>Here's the history:
>
>I installed a Promise TX2000 IDE RAID along with 2 drives. Booted into the BIOS of the TX2000 and defined a RAID-1 array using both drives.
>
>Then, due to circumstances, I had to take out the card and replace it with a plain IDE controller (Promise Ultra 100).
>
>Now when I boot I see the following in dmesg:
>
>===snip!===
>atapci1: <Promise ATA100 controller> port 0xef00-0xef3f,0xefa4-0xefa7,0xefa8-0xefaf,0xeff0-0xeff3,0xefe0-0xefe7 mem 0xffac0000-0xffadffff irq 11 at device 20.0 on pci0
>===snip!===
>ar0: 117301MB <ATA RAID1 array> [14953/255/63] status: DEGRADED subdisks:
> 0 FREE  ad6: 117800MB <IC35L120AVV207-0> [239340/16/63] at ata3-master UDMA100
> 1 READY ad4: 117800MB <IC35L120AVV207-0> [239340/16/63] at ata2-master UDMA100
>===snip!===
>
>So it looks like I have an array (ar0) even though I don't have the RAID controller any more!
>
>`atacontrol list` gives the following:
>ATA channel 0:
>    Master:      no device present
>    Slave:       no device present
>ATA channel 1:
>    Master:      no device present
>    Slave:       no device present
>ATA channel 2:
>    Master:  ad4 <IC35L120AVV207-0/V24OA63A> ATA/ATAPI rev 6
>    Slave:       no device present
>ATA channel 3:
>    Master:  ad6 <IC35L120AVV207-0/V24OA63A> ATA/ATAPI rev 6
>    Slave:       no device present
>
>So I tried `atacontrol detach 3`. Then rebooted. The dmesg about above is from after that boot. The array is still there, but degraded. I'd like to just get rid of it and have my two drives (ad4 and ad6) to use with vinum.
>
>This machine is running 4.5-STABLE #1, any suggestions?
>
>--------------------------
>David Olbersen 
>iGuard Engineer
>11415 West Bernardo Court 
>San Diego, CA 92127 
>1-858-676-2277 x2152
>_______________________________________________
>freebsd-questions@freebsd.org mailing list
>http://lists.freebsd.org/mailman/listinfo/freebsd-questions
>To unsubscribe, send any mail to "freebsd-questions-unsubscribe@freebsd.org"
>
>  
>
I have not used a IDE RAID controler, But I do know RAID.  When you 
create a RAID disk the configuration of the RAID is copied to all of the 
drives and the controller.

I guess, for your problem to use fdisk (8) to regenerate the MBR on one 
of the disks and boot from it.

-Ryan






Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?3E8AEB5F.7080104>