Date: Wed, 19 Jul 2000 21:18:39 +0200 From: Wilko Bulte <wkb@freebie.demon.nl> To: FreeBSD-alpha mailing list <freebsd-alpha@freebsd.org> Subject: Re: test results for Lynx (AS2100A) Message-ID: <20000719211839.A2061@freebie.demon.nl>
next in thread | raw e-mail | index | archive | help
[forgot to cc: -alpha]
On Tue, Jul 18, 2000 at 10:50:19AM -0700, Matthew Jacob wrote:
> boot verbose, please...
Here you are. I have booted a SCSI disk with 4.1RC as of Jul 18 on it
that I pre-installed on a AS2100.
Wilko
Script started on Wed Jul 19 13:16:28 2000
P00>>>sho dev
dka600.6.0.2001.0 DKA600 RRD43 1084
dkb0.0.0.9.0 DKB0 RZ29B 0014
dkb600.6.0.9.0 DKB600 RRD46 0557
dra0.0.0.1003.0 DRA0 5 Member RAID 5 =20
drb0.0.0.2006.0 DRB0 2 Member RAID 1 =20
drb1.0.0.2006.0 DRB1 2 Member RAID 1 =20
drb2.0.0.2006.0 DRB2 2 Member RAID 1 =20
dva0.0.0.1000.0 DVA0 RX26/RX23
ewa0.0.0.7.0 EWA0 00-00-F8-23-16-31
pka0.7.0.2001.0 PKA0 SCSI Bus ID 7
pkb0.7.0.9.0 PKB0 SCSI Bus ID 7 5.57
P00>>>boot dkb0
(boot dkb0.0.0.9.0 -flags A)
block 0 of dkb0.0.0.9.0 is a valid boot block
reading 15 blocks from dkb0.0.0.9.0
bootstrap code read in
base =3D 200000, image_start =3D 0, image_bytes =3D 1e00
initializing HWRPB at 2000
initializing page table at 7ff0000
initializing machine state
setting affinity to the primary CPU
jumping to bootstrap code
VMS PAL rev: 0x4000700010538
OSF PAL rev: 0x4000c0002012d
Switch to OSF PAL code succeeded.
FreeBSD/alpha SRM disk boot, Revision 0.3
(root@miata.wbnet, Tue Jul 18 21:05:09 GMT 2000)
Memory: 131072 k
Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [kernel] in 9 seconds... Booting [kernel] in 8 seconds... Booting [=
kernel]... =20
Entering kernel at 0xfffffc000032b280...
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 18jul00-41rc #0: Tue Jul 18 22:19:33 GMT 2000
root@miata.wbnet:/usr/src/sys/compile/GENERIC
DEC AlphaServer 2100A
AlphaServer 2100A 4/200, 190MHz
8192 byte page size, 1 processor.
CPU: EV4 (21064) major=3D2 minor=3D1
OSF PAL rev: 0x4000c0002012d
real memory =3D 132046848 (128952K bytes)
Physical memory chunk(s):
0x00710000 - 0x07fe5fff, 126705664 bytes (15467 pages)
avail memory =3D 122511360 (119640K bytes)
Preloaded elf kernel "kernel" at 0xfffffc00006f4000.
md0: Malloc disk
Creating DISK md0
found-> vendor=3D0x8086, dev=3D0x0482, revid=3D0x15
class=3D00-00-00, hdrtype=3D0x00, mfdev=3D0
subordinatebus=3D0 secondarybus=3D0
found-> vendor=3D0x1011, dev=3D0x0001, revid=3D0x02
class=3D06-04-00, hdrtype=3D0x01, mfdev=3D0
subordinatebus=3D2 secondarybus=3D2
found-> vendor=3D0x1011, dev=3D0x0002, revid=3D0x24
class=3D02-00-00, hdrtype=3D0x00, mfdev=3D0
subordinatebus=3D0 secondarybus=3D0
intpin=3Da, irq=3D68
map[10]: type 1, range 32, base 00010100, size 7
map[14]: type 1, range 32, base 81111000, size 7
found-> vendor=3D0x1077, dev=3D0x1020, revid=3D0x05
class=3D01-00-00, hdrtype=3D0x00, mfdev=3D0
subordinatebus=3D0 secondarybus=3D0
intpin=3Da, irq=3D76
map[10]: type 1, range 32, base 00010000, size 8
map[14]: type 1, range 32, base 81110000, size 12
found-> vendor=3D0x0000, dev=3D0x0000, revid=3D0x00
class=3Dff-ff-ff, hdrtype=3D0x7f, mfdev=3D1
subordinatebus=3D0 secondarybus=3D0
intpin=3D[, irq=3D33
found-> vendor=3D0x0000, dev=3D0x0000, revid=3D0x00
class=3D00-00-00, hdrtype=3D0x0f, mfdev=3D0
subordinatebus=3D0 secondarybus=3D0
found-> vendor=3D0x0000, dev=3D0x0000, revid=3D0x00
class=3Dff-ff-ff, hdrtype=3D0x7f, mfdev=3D1
subordinatebus=3D0 secondarybus=3D0
intpin=3D[, irq=3D32
found-> vendor=3D0x0000, dev=3D0x0000, revid=3D0x00
class=3D00-00-00, hdrtype=3D0x0f, mfdev=3D0
subordinatebus=3D0 secondarybus=3D0
pci0: <PCI bus> on pcib0
isab0: <Intel 82375EB PCI-EISA bridge> at device 2.0 on pci0
isa0: <ISA bus> on isab0
pcib1: <DEC 21050 PCI-PCI bridge> at device 3.0 on pci0
found-> vendor=3D0x1000, dev=3D0x0001, revid=3D0x11
class=3D01-00-00, hdrtype=3D0x00, mfdev=3D0
subordinatebus=3D0 secondarybus=3D0
intpin=3Da, irq=3D60
map[10]: type 1, range 32, base 00005000, size 8
map[14]: type 1, range 32, base 81004000, size 8
found-> vendor=3D0x1069, dev=3D0x0001, revid=3D0x00
class=3D01-04-00, hdrtype=3D0x00, mfdev=3D0
subordinatebus=3D0 secondarybus=3D0
intpin=3Da, irq=3D80
map[10]: type 1, range 32, base 00005400, size 7
pci2: <PCI bus> on pcib1
sym0: <810a> port 0x5000-0x50ff mem 0x81004000-0x810040ff irq 60 at device =
1.0 on pci2
sym0: No NVRAM, ID 7, Fast-10, SE, parity checking
sym0: open drain IRQ line driver
sym0: using LOAD/STORE-based firmware.
sym0: initial SCNTL3/DMODE/DCNTL/CTEST3/4/5 =3D (hex) 00/00/00/00/00/00
sym0: final SCNTL3/DMODE/DCNTL/CTEST3/4/5 =3D (hex) 03/c2/a0/00/08/00
sym0: Delay (GEN=3D11): 258 msec, 34450 KHz
sym0: Delay (GEN=3D11): 283 msec, 31407 KHz
sym0: Delay (GEN=3D11): 283 msec, 31407 KHz
sym0: interrupting at T2 irq 60
pci2: <unknown card> (vendor=3D0x1069, dev=3D0x0001) at 6.0 irq 80
de0: <Digital 21040 Ethernet> port 0x10100-0x1017f mem 0x81111000-0x8111107=
f irq 68 at device 7.0 on pci0
de0: interrupting at T2 irq 68
de0: DEC 21040 [10Mb/s] pass 2.4
de0: address 00:00:f8:23:16:31
bpf: de0 attached
Qlogic ISP Driver, FreeBSD Version 4.4, Core Version 1.16
isp0: <Qlogic ISP 1020/1040 PCI SCSI Adapter> port 0x10000-0x100ff mem 0x81=
110000-0x81110fff irq 76 at device 9.0 on pci0
isp0: using Memory space register mapping
isp0: set PCI line size to 16
isp0: interrupting at T2 irq 76
isp0: Ultra Mode Capable
isp0: Board Revision 1040B, resident F/W Revision 5.57.1
isp0: Last F/W revision was 5.57.1
isp0: 256 max I/O commands supported
pci0: <unknown card> (vendor=3D0x0000, dev=3D0x0000) at 12.0 irq 33
pci0: <unknown card> (vendor=3D0x0000, dev=3D0x0000) at 12.4
pci0: <unknown card> (vendor=3D0x0000, dev=3D0x0000) at 13.0 irq 32
pci0: <unknown card> (vendor=3D0x0000, dev=3D0x0000) at 13.4
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: interrupting at T2 irq 6
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
kbd0: atkbd0, generic (0), config:0x0, flags:0x1f0000
atkbd0: interrupting at T2 irq 1
psm0: current command byte:0061
kbdc: TEST_AUX_PORT status:0074
kbdc: DIAGNOSE status:0075
psm: keyboard controller failed.
kbdc: TEST_KBD_PORT status:0077
psm: keyboard port failed.
psm0: the aux port is not functioning (116).
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xb8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81=20
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96=20
b9 a3 ff 00 04 02 14 01 05 03 07 38 3c 3a 3e 39=20
3d 3b 3f 04 00 0f 08 00 00 00 00 00 10 0e 00 ff=20
VGA parameters in BIOS for mode 24
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00=20
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00=20
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00=20
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00=20
EGA/VGA parameters to be used for mode 24
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81=20
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96=20
b9 a3 ff 00 04 02 14 01 05 03 07 38 3c 3a 3e 39=20
3d 3b 3f 04 00 0f 08 00 00 00 00 00 10 0e 00 ff=20
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=3D0x0>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
mcclock0: <MC146818A real time clock> at port 0x70-0x71 on isa0
Calibrating clock(s) ... PCC clock: 190008696 Hz (firmware 190114068 Hz)
sio0: configured irq 4 not in bitmap of probed irqs 0x1
sio0: irq maps: 0 0x1 0x1 0x1
sio0 at port 0x3f8-0x3ff irq 4 on isa0
sio0: type 16550A, console
sio0: interrupting at T2 irq 4
sio1: reserved for low-level i/o
isa_probe_children: probing PnP devices
Timecounter "alpha" frequency 190008696 Hz
bpf: sl0 attached
bpf: ppp0 attached
bpf: lo0 attached
bpf: gif0 attached
bpf: gif1 attached
bpf: gif2 attached
bpf: gif3 attached
bpf: faith0 attached
Waiting 15 seconds for SCSI devices to settle
(noperiph:sym0:0:-1:-1): SCSI BUS reset delivered.
isp0: driver initiated bus reset of bus 0
de0: enabling 10baseT port
halted CPU 0
halt code =3D 1
operator initiated halt
PC =3D fffffc00003a2e98
P00>>>=00=00~
[EOT]
wilklt#
wilklt#exit
Script done on Wed Jul 19 13:23:46 2000
--=20
Wilko Bulte http://www.freebsd.org =20
wilko@freebsd.org http://www.nlfug.nl
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-alpha" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20000719211839.A2061>