Date: Fri, 12 Mar 2010 07:12:02 -0500 From: Mister Itanium <itanium.user@gmail.com> To: Marcel Moolenaar <xcllnt@mac.com> Cc: freebsd-ia64@freebsd.org Subject: Re: Installation Problem - 8.0 Message-ID: <230f61611003120412m1cd9704aia0e482f55aca3a77@mail.gmail.com> In-Reply-To: <230f61611003111653o3cc8630bj93e0ce53077e9a2c@mail.gmail.com> References: <230f61611003081111j7f457353g7c28b6cf37a7672@mail.gmail.com> <410865A6-1DCD-4269-91CC-ADE64A3C6E91@mac.com> <230f61611003101913r254d668k152ed5e51ecc9100@mail.gmail.com> <61D1F630-3DA2-47FB-B99F-8B9D7DE87D13@mac.com> <230f61611003110319r68564794k725192b16ae32a8e@mail.gmail.com> <230f61611003111259ja9e91e0mdfd8550df41d64f8@mail.gmail.com> <22F39E8E-C13D-43E7-8AF8-9DAFC14CD6CC@mac.com> <230f61611003111653o3cc8630bj93e0ce53077e9a2c@mail.gmail.com>
next in thread | previous in thread | raw e-mail | index | archive | help
Problem *SOLVED.* HDD was set to "Primary *Slave*", after changing it to *Primary Master* it detected my HD, and I'm now able to proceed with the installation. I've seen a LOT of topics online asking the same question, and I'm wonder if this solution could apply to them all. Thanks, Mr. Itanium On Thu, Mar 11, 2010 at 7:53 PM, Mister Itanium <itanium.user@gmail.com>wrote: > I'm not sure if I should start another email chain or not, but now I'm > having problems at the Installation... > > It pretty much says *"no disks found! Please verify that your disk > controller is being properly probed at boot time. See the hardware guide on > the Documentation menu for clues on diagnosing this type of problem."* > > This is the "boot -v" until the installation point: > > My motherboard is a SuperMicro i2dml-ig2 ( > http://www.supermicro.com/products/motherboard/Itanium/E8870/i2DML-iG2.cfm) > I've searched online, and changed all the settings possible @ Bios, but I'm > still getting the same problem. > Please Advise, > Thanks! > > > >> >> >> > -^H\^HEntering /boot/kernel/kernel at 0xe000000004080000... > > PAL Proc at 0xe00000007ff08010 > SAL Proc at 0xe00000007ff48020, GP at 0xe0000000801712c0 > SAL: AP wake-up vector: 0xf0 > Platform clock frequency 199475857 Hz > Processor ratio 14/2, Bus ratio 1/1, ITC ratio 14/2 > ptc.e base=0x0, count1=1, count2=1, stride1=0x0, stride2=0x0 > Processor supports 24 Region ID bits > Trying VHPT size 0x1000000 > Putting VHPT at 0x6000000 > Splitting [0x560c000-0x7fb40000] > Copyright (c) 1992-2009 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD is a registered trademark of The FreeBSD Foundation. > FreeBSD 8.0-RELEASE #0: Sun Nov 22 01:11:28 UTC 2009 > root@pluto1.freebsd.org:/usr/obj/usr/src/sys/GENERIC > UNWIND: table added: base=e000000004000000, start=e000000004bbb060, > end=e000000004bfc250 > Preloaded elf kernel "/boot/kernel/kernel" at 0xe000000005608580. > Preloaded mfs_root "/boot/mfsroot" at 0xe000000005608660. > CPU: Madison (1396.33-Mhz Itanium 2) > Origin = "GenuineIntel" Revision = 5 > Features = 0x1<LB> > real memory = 4282097664 (4083 MB) > > Physical memory chunk(s): > 0x01900000 - 0x03ffffff, 40894464 bytes (4992 pages) > 0x0560c000 - 0x05ffffff, 10436608 bytes (1274 pages) > 0x0a000000 - 0x7fb3ffff, 1974730752 bytes (241056 pages) > 0x7ff7c000 - 0x7ff81fff, 24576 bytes (3 pages) > > 0x180000000 - 0x1fb455fff, 2068144128 bytes (252459 pages) > 0x1feffe000 - 0x1ff453fff, 4546560 bytes (555 pages) > 0x1ff802000 - 0x1ff8fdfff, 1032192 bytes (126 pages) > 0x1ff900000 - 0x1ff905fff, 24576 bytes (3 pages) > > 0x1ff9fe000 - 0x1ffd63fff, 3563520 bytes (435 pages) > 0x1ffdfe000 - 0x1ffe0ffff, 73728 bytes (9 pages) > 0x1ffe7e000 - 0x1fffb7fff, 1286144 bytes (157 pages) > avail memory = 4084006912 (3894 MB) > > FPSWA Revision = 0x10012, Entry = 0xe0000001ffe60050 > Table 'FACP' at 0xe00000007ff99138 > Table 'APIC' at 0xe00000007ff99230 > Local APIC address=0xfee00000 > Local SAPIC entry > ProcessorId=0x0, Id=0xc0, Eid=0x18 > Local SAPIC entry > ProcessorId=0x1, Id=0xc6, Eid=0x18 > I/O SAPIC entry > Id=0x0, InterruptBase=0x0, Address=0xfec00000 > I/O SAPIC entry > Id=0x2, InterruptBase=0x18, Address=0xfaffe000 > I/O SAPIC entry > Id=0x1, InterruptBase=0x30, Address=0xfafff000 > Interrupt source override entry > Bus=0, Source=9, Irq=0x9 > Platform interrupt entry > Polarity=3, TriggerMode=3, Id=0xc6, Eid=0x18, Vector=0x1e, > Irq=22 > Table 'IPPT' at 0xe00000007ff99308 > Table 'SPCR' at 0xe00000007ff99340 > MCA: allocated 16384 bytes for state info. > SMP: waking up cpu1 > FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs > cpu0: ACPI Id=1, SAPIC Id=c6, SAPIC Eid=18 (BSP) > cpu1: ACPI Id=0, SAPIC Id=c0, SAPIC Eid=18 > ULE: setup cpu 0 > ULE: setup cpu 1 > mem: <memory> > null: <null device, zero device> > nfslock: pseudo-device > random: <entropy source, Software, Yarrow> > ACPI: RSDP 0x7ff99000 00024 (v2 AMI ) > ACPI: XSDT 0x7ff99090 00044 (v1 AMI TIGER_2W 01072002 MSFT 00010013) > ACPI: FACP 0x7ff99138 000F4 (v3 AMI TIGER_2W 01072002 MSFT 00010013) > ACPI: DSDT 0x7ff9b000 0220E (v1 AMI TIGER2W 00000000 MSFT 0100000D) > ACPI: FACS 0x7ff992c0 00040 > ACPI: APIC 0x7ff99230 0008E (v1 AMI TIGER_2W 01072002 MSFT 00010013) > ACPI: IPPT 0x7ff99308 00034 (v1 AMI TIGER_2W 01072002 MSFT 00010013) > ACPI: SPCR 0x7ff99340 00050 (v1 AMI TIGER_2W 01072002 MSFT 00010013) > nexus0: registered as a time-of-day clock (resolution 1000us) > acpi0: <AMI TIGER_2W> on motherboard > acpi0: [MPSAFE] > acpi0: [ITHREAD] > acpi0: Power Button (fixed) > AcpiOsDerivePciId: \_SB_.CSFF.IOH5.IOHC -> bus 255 dev 28 func 5 > AcpiOsDerivePciId: \_SB_.CSFF.IOH1.IO01 -> bus 255 dev 28 func 1 > AcpiOsDerivePciId: \_SB_.CSFF.IOH2.IO02 -> bus 255 dev 28 func 2 > ACPI timer: 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 -> 10 > Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 > acpi_timer0: <24-bit timer at 3.579545MHz> port 0xc08-0xc0b on acpi0 > pcib0: <ACPI Host-PCI bridge> on acpi0 > pci0: <ACPI PCI bus> on pcib0 > pci0: domain=0, physical bus=0 > found-> vendor=0x8086, dev=0x244e, revid=0x82 > domain=0, bus=0, slot=30, func=0 > class=06-04-00, hdrtype=0x01, mfdev=0 > cmdreg=0x0147, statreg=0x0080, cachelnsz=0 (dwords) > lattimer=0x00 (0 ns), mingnt=0x0b (2750 ns), maxlat=0x00 (0 ns) > found-> vendor=0x8086, dev=0x24c0, revid=0x02 > domain=0, bus=0, slot=31, func=0 > class=06-01-00, hdrtype=0x00, mfdev=1 > cmdreg=0x010f, statreg=0x0280, cachelnsz=0 (dwords) > lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) > found-> vendor=0x8086, dev=0x24cb, revid=0x02 > domain=0, bus=0, slot=31, func=1 > class=01-01-8a, hdrtype=0x00, mfdev=0 > cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) > lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) > intpin=a, irq=0 > map[20]: type I/O Port, range 32, base 0x1000, size 4, enabled > map[24]: type Memory, range 32, base 0, size 10, memory disabled > pcib0: no PRT entry for 0.31.INTA > found-> vendor=0x8086, dev=0x24c3, revid=0x02 > domain=0, bus=0, slot=31, func=3 > class=0c-05-00, hdrtype=0x00, mfdev=0 > cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords) > lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) > intpin=b, irq=0 > map[20]: type I/O Port, range 32, base 0xcc0, size 5, enabled > pcib0: no PRT entry for 0.31.INTB > pcib1: <ACPI PCI-PCI bridge> at device 30.0 on pci0 > pcib1: domain 0 > pcib1: secondary bus 1 > pcib1: subordinate bus 1 > pcib1: I/O decode 0xd000-0xdfff > pcib1: memory decode 0xfb000000-0xfd0fffff > pcib1: no prefetched decode > pcib1: Subtractively decoded bridge. > pci1: <ACPI PCI bus> on pcib1 > pci1: domain=0, physical bus=1 > found-> vendor=0x1002, dev=0x4752, revid=0x27 > domain=0, bus=1, slot=2, func=0 > class=03-00-00, hdrtype=0x00, mfdev=0 > cmdreg=0x0087, statreg=0x0290, cachelnsz=32 (dwords) > lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns) > intpin=a, irq=11 > powerspec 2 supports D0 D1 D2 D3 current D0 > map[10]: type Memory, range 32, base 0xfc000000, size 24, enabled > pcib1: requested memory range 0xfc000000-0xfcffffff: good > map[14]: type I/O Port, range 32, base 0xd800, size 8, enabled > pcib1: requested I/O range 0xd800-0xd8ff: in range > map[18]: type Memory, range 32, base 0xfd0ff000, size 12, enabled > pcib1: requested memory range 0xfd0ff000-0xfd0fffff: good > pcib1: matched entry for 1.2.INTA > pcib1: slot 2 INTA hardwired to IRQ 18 > vgapci0: <VGA-compatible display> port 0xd800-0xd8ff mem > 0xfc000000-0xfcffffff,0xfd0ff000-0xfd0fffff irq 18 at device 2.0 on pci1 > pci0: <bridge, PCI-ISA> at device 31.0 (no driver attached) > atapci0: <Intel ICH4 UDMA100 controller> port > 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x1000-0x100f irq 0 at device 31.1 on > pci0 > atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0x1000 > ata0: <ATA channel 0> on atapci0 > atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0 > atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6 > ata0: reset tp1 mask=03 ostat0=00 ostat1=50 > ata0: stat0=0x01 err=0x01 lsb=0x01 msb=0x01 > ata0: stat1=0x01 err=0x01 lsb=0x01 msb=0x01 > ata0: reset tp2 stat0=01 stat1=01 devices=0x0 > ata0: [MPSAFE] > ata0: [ITHREAD] > ata1: <ATA channel 1> on atapci0 > atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170 > atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376 > ata1: reset tp1 mask=03 ostat0=50 ostat1=01 > ata1: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb > ata1: stat1=0x01 err=0x04 lsb=0x00 msb=0x00 > ata1: reset tp2 stat0=00 stat1=01 devices=0x10000 > ata1: [MPSAFE] > ata1: [ITHREAD] > pci0: <serial bus, SMBus> at device 31.3 (no driver attached) > pcib2: <ACPI Host-PCI bridge> on acpi0 > pcib2: could not get PCI interrupt routing table for \_SB_.PCI1 - > AE_NOT_FOUND > pci2: <ACPI PCI bus> on pcib2 > pci2: domain=0, physical bus=2 > found-> vendor=0x8086, dev=0x1461, revid=0x04 > domain=0, bus=2, slot=28, func=0 > class=08-00-20, hdrtype=0x00, mfdev=0 > cmdreg=0x0106, statreg=0x0030, cachelnsz=0 (dwords) > > lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) > map[10]: type Memory, range 32, base 0xfafff000, size 12, enabled > found-> vendor=0x8086, dev=0x1460, revid=0x04 > domain=0, bus=2, slot=29, func=0 > > class=06-04-00, hdrtype=0x01, mfdev=0 > cmdreg=0x0147, statreg=0x0030, cachelnsz=32 (dwords) > lattimer=0x40 (1920 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns) > found-> vendor=0x8086, dev=0x1461, revid=0x04 > domain=0, bus=2, slot=30, func=0 > class=08-00-20, hdrtype=0x00, mfdev=0 > cmdreg=0x0106, statreg=0x0030, cachelnsz=0 (dwords) > > lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) > map[10]: type Memory, range 32, base 0xfaffe000, size 12, enabled > found-> vendor=0x8086, dev=0x1460, revid=0x04 > domain=0, bus=2, slot=31, func=0 > > class=06-04-00, hdrtype=0x01, mfdev=0 > cmdreg=0x0147, statreg=0x0030, cachelnsz=32 (dwords) > lattimer=0x40 (1920 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns) > pci2: <base peripheral, interrupt controller> at device 28.0 (no driver > attached) > pcib3: <ACPI PCI-PCI bridge> at device 29.0 on pci2 > pcib3: domain 0 > pcib3: secondary bus 3 > pcib3: subordinate bus 3 > pcib3: I/O decode 0xf000-0xffff > pcib3: memory decode 0xfa000000-0xfa0fffff > pcib3: no prefetched decode > pci3: <ACPI PCI bus> on pcib3 > pci3: domain=0, physical bus=3 > found-> vendor=0x8086, dev=0x1010, revid=0x01 > domain=0, bus=3, slot=2, func=0 > class=02-00-00, hdrtype=0x00, mfdev=1 > cmdreg=0x0117, statreg=0x0230, cachelnsz=32 (dwords) > lattimer=0x40 (1920 ns), mingnt=0xff (63750 ns), maxlat=0x00 (0 ns) > intpin=a, irq=3 > > powerspec 2 supports D0 D3 current D0 > MSI supports 1 message, 64 bit > map[10]: type Memory, range 64, base 0xfa0c0000, size 17, enabled > pcib3: requested memory range 0xfa0c0000-0xfa0dffff: good > map[20]: type I/O Port, range 32, base 0xfe80, size 6, enabled > pcib3: requested I/O range 0xfe80-0xfebf: in range > pcib3: matched entry for 3.2.INTA > pcib3: slot 2 INTA hardwired to IRQ 48 > found-> vendor=0x8086, dev=0x1010, revid=0x01 > domain=0, bus=3, slot=2, func=1 > class=02-00-00, hdrtype=0x00, mfdev=1 > cmdreg=0x0117, statreg=0x0230, cachelnsz=32 (dwords) > lattimer=0x40 (1920 ns), mingnt=0xff (63750 ns), maxlat=0x00 (0 ns) > intpin=b, irq=3 > > powerspec 2 supports D0 D3 current D0 > MSI supports 1 message, 64 bit > map[10]: type Memory, range 64, base 0xfa0e0000, size 17, enabled > pcib3: requested memory range 0xfa0e0000-0xfa0fffff: good > map[20]: type I/O Port, range 32, base 0xff00, size 6, enabled > pcib3: requested I/O range 0xff00-0xff3f: in range > pcib3: matched entry for 3.2.INTB > pcib3: slot 2 INTB hardwired to IRQ 49 > em0: <Intel(R) PRO/1000 Network Connection 6.9.14> port 0xfe80-0xfebf mem > 0xfa0c0000-0xfa0dffff irq 48 at device 2.0 on pci3 > em0: Reserved 0x20000 bytes for rid 0x10 type 3 at 0xfa0c0000 > em0: Reserved 0x40 bytes for rid 0x20 type 4 at 0xfe80 > em0: [FILTER] > em0: bpf attached > em0: Ethernet address: 00:30:48:20:f6:2a > em1: <Intel(R) PRO/1000 Network Connection 6.9.14> port 0xff00-0xff3f mem > 0xfa0e0000-0xfa0fffff irq 49 at device 2.1 on pci3 > em1: Reserved 0x20000 bytes for rid 0x10 type 3 at 0xfa0e0000 > em1: Reserved 0x40 bytes for rid 0x20 type 4 at 0xff00 > em1: [FILTER] > em1: bpf attached > em1: Ethernet address: 00:30:48:20:f6:2b > pci2: <base peripheral, interrupt controller> at device 30.0 (no driver > attached) > pcib4: <ACPI PCI-PCI bridge> at device 31.0 on pci2 > pcib4: domain 0 > pcib4: secondary bus 4 > pcib4: subordinate bus 4 > pcib4: I/O decode 0xf000-0xfff > pcib4: no prefetched decode > pci4: <ACPI PCI bus> on pcib4 > pci4: domain=0, physical bus=4 > uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 on acpi0 > uart0: [FILTER] > uart0: fast interrupt > uart0: console (115200,n,8,1) > cpu0: <ACPI CPU> on acpi0 > cpu0: switching to generic Cx mode > cpu1: <ACPI CPU> on acpi0 > Reducing kern.maxvnodes 131431 -> 100000 > procfs registered > Timecounters tick every 1.000 msec > lo0: bpf attached > ata0: Identifying devices: 00000000 > ata0: New devices: 00000000 > ata1: Identifying devices: 00010000 > ata1: New devices: 00010000 > md0: Preloaded image </boot/mfsroot> 8388608 bytes at 0xe000000004e08580 > ata1-master: pio=PIO4 wdma=WDMA2 udma=UDMA33 cable=40 wire > acd0: setting PIO4 on ICH4 chip > acd0: setting UDMA33 on ICH4 chip > acd0: <CD-224E/1.9A> CDROM drive at ata1 as master > acd0: read 4134KB/s (4134KB/s), 128KB buffer, UDMA33 > acd0: Reads: CDR, CDRW, CDDA stream, packet > acd0: Writes: > acd0: Audio: play, 256 volume levels > acd0: Mechanism: ejectable tray, unlocked > acd0: Medium: CD-ROM 120mm data disc > ATA PseudoRAID loaded > acd0: FAILURE - READ_BIG MEDIUM ERROR asc=0x11 ascq=0x00 > acd0: FAILURE - READ_BIG MEDIUM ERROR asc=0x11 ascq=0x00 > Trying to mount root from ufs:/dev/md0 > ct_to_ts([2010-03-12 00:24:18]) = 1268353458.000000000 > start_init: trying /sbin/init > start_init: trying /sbin/oinit > start_init: trying /sbin/init.bak > start_init: trying /rescue/init > start_init: trying /stand/sysinstall > /stand/sysinstall running as init on serial console > > These are the predefined terminal types available to > sysinstall when running stand-alone. Please choose the > closest match for your particular terminal. > > 1 ...................... Standard ANSI terminal. > 2 ...................... VT100 or compatible terminal. > 3 ...................... FreeBSD system console (color). > 4 ...................... FreeBSD system console (monochrome). > > 5 ...................... xterm terminal emulator. > > Your choice: (1-5) >
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?230f61611003120412m1cd9704aia0e482f55aca3a77>