Skip site navigation (1)Skip section navigation (2)
Date:      Wed, 25 Feb 2004 16:48:11 -0000
From:      "Aled Treharne" <Aled.T@mistral.net>
To:        <questions@freebsd.org>
Subject:   Install disk gives "READ_DMA recovered from missing interrupt" errors...
Message-ID:  <D869343A133CF94B8C7985D6DBDFAB8771B9@hqex2.hq.mistral.co.uk>

next in thread | raw e-mail | index | archive | help
Hiya.

I've been trying to get FreeBSD onto a bunch of Nexcom blade servers
that we have hanging around - all of the blades are HDB31670's, with
Intel P-III 1.1Ghz, 1Gb of RAM and 40Gb Fujitsu HDD's. I had a nightmare
of a time with 4.9 with kernel panics on boot, so I tried 5.2, but I'm
still seing problems. I've included the dmesg below, but basically I'm
seeing the same error over and over while sysinstall tries to write the
partition table.=20

Has anyone seen this before or something similar, or can anyone offer
any advice? I'd love to get FBSD installed on these blades since I
believe that it'll perform better than RedHat or Debian on there (which
is the whole reason for this).

Thanks in advance for any assistance.

*********


Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights
reserved.
FreeBSD 5.2-RELEASE #0: Sun Jan 11 04:21:45 GMT 2004
    root@wvu1.btc.adaptec.com:/usr/obj/usr/src/sys/GENERIC
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0e6b000.
Perloaded mfs_root "/boot/mfsroot" at 0xc0e6b1f4.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc0e6b238.
Timecounter "i8254" frequency 1193182Hz quality 0
CPU: Intel (R) Pentium(R) III CPU Family    1133MHz (1132.79-MHz
686-class CPU)
  Origin =3D "GenuineIntel" Id =3D 0x6b1  Stepping =3D1
=20
Features=3D0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE=
,
MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory  =3D 1073676288 (1023 MB)
avail memory =3D 1029324800 (981 MB)
ACPI APIC Table: <RCC    AWRDACPI>
ioapic0 <Version 1.1> irps 0-15 on motherboard
ioapic1 <version 1.1> irqs 16-31 on motherboard
Pentium Pro MTRR support enabled
npx0: [FAST]
stray irq13
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <RCC    AWRDACPI> on motherboard
    ACPI-0538: *** Error: Looking up [\_PR_.CPU0] in namespace,
AE_NOT_FOUND
SearchNode 0xc6d5e3e0 StartNode 0xc6d5e3e0 ReturnNode 0
    ACPI-1287: *** Error: , AE_NOT_FOUND
acpi0: Sleep Button (fixed)
Timecounter "ACPI-safe" frequency 6579545 Hz quality 1000
pcibios: BIOS version 2.10
Using $PIR table, 6 entries at 0xc00fdd30
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x208-0x50b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_cpu1: <CPU> on acpi0
device_probe_and_attach: acpi_cpu1 attach returned 6
acpi_tz0: <Thermal Zone> on acpi0
    ACPI-0438: *** Error: Looking up [\_PR_.CPU0] in namespace,
AE_NOT_FOUND
SearchNode 0xc6d5e3e0 StartNode 0xc6d5e3e0 ReturnNode 0
    ACPI-1287: *** Error: , AE_NOT_FOUND
acpi_button0: <Power Button> on acpi0
pcib0:<ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: <display, VGA> at device 12.0 (no driver attached)
fxp0: <Intel 82559 Pro/100 Ethernet> port 0xd000-0xd03f mem
0xfa000000-0xfa0fffff,0xfa100000-0xfa100fff irq 30 at device 14.0 on
pci0
fxp0: Ethernet address 00:10:f3:00:9a:1f
miibus0: <MII bus> on fxp0
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isab0: <PCI-ISA bridge> at device 15.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <ServerWorks CSB5 UDMA100 controller> port
0xe800-0xe803,0xe400-0xe40f,0xe000-0xe003,0xdc00-0xdc07,0xd800-0xd803,0x
d400-0xd407 at device 15.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata0: [MPSAFE]
ata1: at 0x170 irq 15 on atapci0
ata1: [MPSAFE]
pcib1: <ACPI Host-PCI bridge> on acpi0
pci1: <ACPI PCI bus> on pcib1
bge0: <Broadcom BCM5701 Gigabit Ethernet, ASIC rev. 0x105> mem
0xfb000000-0xfb00ffff irq 28 at device 12.0 on pci1
bge0: Ethernet address 00:10:f3:00:9a:1d
miibus1: <MII bus> on bge0
brgphy0: <BCM5701 10/100/1000baseTX PHY> on miibus1
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX,
1000baseTX-FDX, auto
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone )> port
0x3f7,0x3f2-0x3f5 irq 6 drq 2 on acpi0
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
acpi_cpu1: <CPU> on acpi0
device_probe_and_attach: acpi_cpu1 attach returned 6
pmtimer on isa0
ppc0: parallel port not found
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=3D0x300>
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 8250 or not responding
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
isa0
Timecounter "TSC" frequency 1132792335 Hz quality 800
Timecoutners tick every 10.000 msec
md0: Preloaded image </boot/mfsroot> 4423680 bytes at 0xc09dff74
GEOM: create disk ad0 dp=3D0xc6db2e60
ad0: 38154MB <FUJITSU MHR2040AT> [77520/16/63] at ata0-master UDAM100
ad0: WARNING - READ_DMA recovered from missing interrupt
acd0: CDROM  <NEC CD-ROM DRIVE:291> at ata1-slave PIO4
ad0: WARNING - READ_DMA recovered from missing interrupt
    ACPI-0438: *** Error: Looking up [\_PR_.CPU0] in namespace,
AE_NOT_FOUND SearchNode 0xc6d5e3e0 StartNode 0xc6d5e3e0 ReturnNode 0
    ACPI-1287: *** Error: , AE_NOT_FOUND
    ACPI-0438: *** Error: Looking up [\_PR_.CPU0] in namespace,
AE_NOT_FOUND SearchNode 0xc6d5e3e0 StartNode 0xc6d5e3e0 ReturnNode 0
    ACPI-1287: *** Error: , AE_NOT_FOUND
ad0: WARNING - READ_DMA recovered from missing interrupt
ad0: WARNING - READ_DMA recovered from missing interrupt
Mounting root from ufs :/dev/md0
/stand/sysinstall running as init on vty0


*****

Cheers,
Aled.

--=20
Aled Treharne - Network Operations - Mistral Internet
Tel: 0870 751 6300 Fax: 0870 751 6399  http://www.mistral.net=20

This electronic message contains information from Mistral Internet which
may be privileged or confidential. The information is intended to be for
the use of the individual(s) or entity named above. If you are not the
intended recipient be aware that any disclosure, copying, distribution
or use of the contents of this information is prohibited. If you have
received this electronic message in error, please notify us by telephone
or email (to the numbers or address above) immediately.



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?D869343A133CF94B8C7985D6DBDFAB8771B9>