Date: Thu, 11 May 2000 12:27:30 -0600 From: Brad Waite <brad@ssbaptist.net> To: questions@freebsd.org Subject: Problems upgrading from 3.4 to 4.0 Message-ID: <391AFB92.5475A7A0@ssbaptist.net>
next in thread | raw e-mail | index | archive | help
Hi all,
I'm trying to upgrade from a relatively new install of 3.4 to 4.0 via
CD. I boot to the atapi CDROM, and choose upgrade from the sysinstall
menu. After selecting the distros, it puts me in the partition editor,
but da0 doesn't show any existing partitions. A secondary, single
partition SCSI raid shows its partition fine on da1. I've included
debug and dmesg output below.
Any ideas what could be happening?
Thanks,
Brad
4.0 sysinstall debug:
---------------------
da0: bad sector table not supported
da0s1: bad sector table not supported
(repeated several times)
3.4 dmesg:
----------
FreeBSD 3.4-RELEASE #1: Wed Apr 19 09:40:55 MDT 2000
root@susie:/usr/src/sys/compile/SUSIE
Timecounter "i8254" frequency 1193182 Hz
Timecounter "TSC" frequency 451026354 Hz
CPU: AMD-K6(tm) 3D processor (451.03-MHz 586-class CPU)
Origin = "AuthenticAMD" Id = 0x58c Stepping = 12
Features=0x8021bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,PGE,MMX>
AMD Features=0x80000800<SYSCALL,3DNow!>
real memory = 67108864 (65536K bytes)
avail memory = 62328832 (60868K bytes)
Preloaded elf kernel "kernel" at 0xc02c8000.
Probing for devices on PCI bus 0:
chip0: <VIA 82C597 (Apollo VP3) system controller> rev 0x04 on pci0.0.0
chip1: <VIA 82C598MVP (Apollo MVP3) PCI-PCI bridge> rev 0x00 on pci0.1.0
chip2: <PCI to ISA bridge (vendor=1106 device=0686)> rev 0x1b on
pci0.7.0
ide_pci0: <VIA 82C586x (Apollo) Bus-master IDE controller> rev 0x06 on
pci0.7.1
chip3: <Host to PCI bridge (vendor=1106 device=3057)> rev 0x20 on
pci0.7.4
ahc0: <Adaptec 2940 Ultra SCSI adapter> rev 0x00 int a irq 10 on
pci0.8.0
ahc0: aic7880 Wide Channel A, SCSI Id=7, 16/255 SCBs
xl0: <3Com 3c905B-TX Fast Etherlink XL> rev 0x00 int a irq 5 on
pci0.10.0
xl0: Ethernet address: 00:10:5a:02:2f:e5
xl0: autoneg complete, link status good (half-duplex, 100Mbps)
vga0: <S3 Aurora 64 graphics accelerator> rev 0x00 int a irq 11 on
pci0.11.0
Probing for devices on PCI bus 1:
Probing for PnP devices:
Probing for devices on the ISA bus:
sc0 on isa
sc0: VGA color <16 virtual consoles, flags=0x0>
atkbdc0 at 0x60-0x6f on motherboard
atkbd0 irq 1 on isa
psm0 irq 12 on isa
psm0: model Generic PS/2 mouse, device ID 0
sio0 at 0x3f8-0x3ff irq 4 flags 0x10 on isa
sio0: type 16550A
sio1 at 0x2f8-0x2ff irq 3 on isa
sio1: type 16550A
fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa
fdc0: FIFO enabled, 8 bytes threshold
fd0: 1.44MB 3.5in
wdc0 at 0x1f0-0x1f7 irq 14 on isa
wdc0: unit 0 (atapi): <DF7910C(-D0161 )/2V11>, removable, intr, iordy
acd0: drive speed 2636KB/sec, 255KB cache
acd0: supported read types:
acd0: Audio: play, 255 volume levels
acd0: Mechanism: ejectable tray
acd0: Medium: CD-ROM 120mm data disc loaded, unlocked
wdc1 not found at 0x170
ppc0 at 0x378 irq 7 flags 0x40 on isa
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
lpt0: <generic printer> on ppbus 0
lpt0: Interrupt-driven port
ppi0: <generic parallel i/o> on ppbus 0
plip0: <PLIP network interface> on ppbus 0
ep0 not found at 0x300
vga0 at 0x3b0-0x3df maddr 0xa0000 msize 131072 on isa
npx0 on motherboard
npx0: INT 16 interface
changing root device to da0s1a
da1 at ahc0 bus 0 target 6 lun 0
da1: <CMD TECH CRD-5000 D.4> Fixed Direct Access SCSI-2 device
da1: 3.300MB/s transfers
da1: 52017MB (106530816 512 byte sectors: 64H 32S/T 52017C)
da0 at ahc0 bus 0 target 2 lun 0
da0: <SEAGATE ST15150W 0022> Fixed Direct Access SCSI-2 device
da0: 20.000MB/s transfers (10.000MHz, offset 8, 16bit), Tagged Queueing
Enabled
da0: 4095MB (8388315 512 byte sectors: 64H 32S/T 4095C)
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?391AFB92.5475A7A0>