Date: Sat, 05 Oct 2002 08:18:50 +0000 (GMT) From: Daniel Flickinger <attila@hun.org> To: Poul-Henning Kamp <phk@critter.freebsd.dk> Cc: FreeBSD-CURRENT <current@freebsd.org>, Eric Hodel <drbrain@segment7.net> Subject: Re: HEADSUP! GEOM as default in 5 days... GEOM does not find da0a; goes to rootmount> Message-ID: <20021005081850.zmEf69968@hun.org> References: <80828.1033798404@critter.freebsd.dk>, <20021005015843.GA17340@segment7.net>
next in thread | previous in thread | raw e-mail | index | archive | help
I tried the GEOM declaration again with a kernel current as of 05 Oct 0000 GMT --it failed apparently trying to load off the ZIP disk at da2 after not finding the da0/1 drives on the aic7899 (Tyan 2642 SMP) I will note that my loader is dated 27 Sep since there has not been an even close to complete buildworld since then; I cvsup at least twice a day: 0000 and 1200. several of the boot modules are among the casualites along with disklabel. Sure hope you're going to put the NOGEOM flag for the config flag in tomorrow! ----- dmesg: slice 0000 GMT 05 Oct ------ Copyright (c) 1992-2002 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.0-CURRENT #103: Sat Oct 5 03:39:04 GMT 2002 root@hun.org:/usr/obj/usr/src/sys/hun Preloaded elf kernel "/boot/kernel/kernel" at 0xc08da000. Preloaded mfs_root "/boot/mfsroot" at 0xc08da0b4. Preloaded elf module "/boot/kernel/acpi.ko" at 0xc08da0f8. Timecounter "i8254" frequency 1193182 Hz CPU: AMD Athlon(tm) Processor (1194.68-MHz 686-class CPU) Origin = "AuthenticAMD" Id = 0x662 Stepping = 2 Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE> AMD Features=0xffffffffc0480000<MP,AMIE,DSP,3DNow!> real memory = 536805376 (524224K bytes) avail memory = 511938560 (499940K bytes) Programming 24 pins in IOAPIC #0 IOAPIC #0 intpin 2 -> irq 0 GEOMetry statement somewhere in here... FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs cpu0 (BSP): apic id: 1, version: 0x00040010, at 0xfee00000 cpu1 (AP): apic id: 0, version: 0x00040010, at 0xfee00000 io0 (APIC): apic id: 2, version: 0x00170011, at 0xfec00000 Pentium Pro MTRR support enabled md0: Preloaded image </boot/mfsroot> 4423680 bytes at 0xc04604b8 npx0: <math processor> on motherboard npx0: INT 16 interface acpi0: <PTLTD RSDT > on motherboard acpi0: power button is handled as a fixed feature programming model. acpi0: sleep button is handled as a fixed feature programming model. Timecounter "ACPI-fast" frequency 3579545 Hz acpi_timer0: <24-bit timer at 3.579545MHz> port 0x8008-0x800b on acpi0 acpi_cpu0: <CPU> on acpi0 acpi_cpu1: <CPU> on acpi0 acpi_button0: <Power Button> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0x8080-0x80ff,0x8000-0x807f,0xcf8-0xcff iomem 0xdc000-0xdffff on acpi0 pci0: <ACPI PCI bus> on pcib0 agp0: <AMD 762 host to AGP bridge> port 0x2010-0x2013 mem 0xf4005000-0xf4005fff,0xf8000000-0xfbffffff at device 0.0 on pci0 pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0 pci1: <ACPI PCI bus> on pcib1 pci1: <display, VGA> at device 5.0 (no driver attached) isab0: <PCI-ISA bridge> at device 7.0 on pci0 isa0: <ISA bus> on isab0 pci0: <mass storage, ATA> at device 7.1 (no driver attached) pci0: <bridge, PCI-unknown> at device 7.3 (no driver attached) pci0: <serial bus, USB> at device 7.4 (no driver attached) trm0: <Tekram DC395U/UW/F DC315/U Fast20 Wide SCSI Adapter> port 0x1000-0x10ff mem 0xf4001000-0xf4001fff irq 10 at device 8.0 on pci0 sio0: <3COM PCI FaxModem> port 0x2018-0x201f irq 11 at device 9.0 on pci0 sio0: moving to sio2 sio2: type 16550A ahc0: <Adaptec aic7899 Ultra160 SCSI adapter> port 0x1400-0x14ff mem 0xf4002000-0xf4002fff irq 10 at device 13.0 on pci0 aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs ahc1: <Adaptec aic7899 Ultra160 SCSI adapter> port 0x1800-0x18ff mem 0xf4003000-0xf4003fff irq 11 at device 13.1 on pci0 ahc1: bus_alloc_resource() failed to allocate IRQ device_probe_and_attach: ahc1 attach returned 12 xl0: <3Com 3c980C Fast Etherlink XL> port 0x1c00-0x1c7f mem 0xf4004000-0xf400407f irq 5 at device 15.0 on pci0 xl0: Ethernet address: 00:e0:81:03:e2:89 miibus0: <MII bus> on xl0 ukphy0: <Generic IEEE 802.3u media interface> on miibus0 ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto xl1: <3Com 3c980C Fast Etherlink XL> port 0x1c80-0x1cff mem 0xf4004400-0xf400447f irq 11 at device 16.0 on pci0 xl1: couldn't map interrupt device_probe_and_attach: xl1 attach returned 6 atspeaker0 port 0x61 on acpi0 atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: model Generic PS/2 mouse, device ID 0 sio0 port 0x3f8-0x3ff irq 4 on acpi0 sio0: type 16550A ppc0 port 0x778-0x77f,0x378-0x37f irq 7 drq 3 on acpi0 ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode ppbus0: IEEE1284 device found /NIBBLE/ECP/ECP_RLE Probing for PnP devices on ppbus0: ppbus0: <Hewlett-Packard HP LaserJet 5000 Series> PJL,MLC,PCL,PCLXL,POSTSCRIPT lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 fdc0: <enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 orm0: <Option ROMs> at iomem 0xe0000-0xe3fff,0xce800-0xd67ff,0xce000-0xce7ff,0xcd800-0xcdfff,0xc0000-0xc7fff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <12 virtual consoles, flags=0x300> sio1 at port 0x2f8-0x2ff irq 3 on isa0 sio1: type 16550A vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 APIC_IO: Testing 8254 interrupt delivery APIC_IO: routing 8254 via IOAPIC #0 intpin 2 Timecounters tick every 10.000 msec ipfw2 initialized, divert enabled, rule-based forwarding enabled, default to accept, logging limited to 100 packets/entry by default BRIDGE 020214 loaded DUMMYNET initialized (011031) IPv6 packet filtering initialized, default to accept, logging limited to 100 packets/entry IPsec: Initialized Security Association Processing. IP Filter: v3.4.29 initialized. Default = pass all, Logging = enabled Waiting 2 seconds for SCSI devices to settle SMP: AP CPU #1 Launched! cd0 at trm0 bus 0 target 6 lun 0 cd0: <CREATIVE DVD-RAM RAM1216S 1311> Removable CD-ROM SCSI-2 device cd0: 10.000MB/s transfers (10.000MHz, offset 15) cd0: cd present [1218960 x 2048 byte records] Mounting root from ufs:/dev/da0a Invalid time in real time clock. Check and reset the date immediately! da2 at trm0 bus 0 target 5 lun 0 da2: <IOMEGA ZIP 100 N*32> Removable Direct Access SCSI-2 device da2: 3257782.488MB/s transfers da2: 96MB (196608 512 byte sectors: 64H 32S/T 96C) (da2:trm0:0:5:0) Synchronize cache failed, status == 0x80, scsi status == 0x2 ...repeated 20 times set root by name failed ffd_mountrout can't find rootvp root mount failed: 6 ...repeated several times ...instructions mountroot > To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-current" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20021005081850.zmEf69968>