Skip site navigation (1)Skip section navigation (2)
Date:      Fri, 6 Jun 2003 08:21:26 +0100
From:      "Chris Ward" <chris.p.ward@ntlworld.com>
To:        "yussef" <yussef@claygirl.org>
Cc:        freebsd-questions@freebsd.org
Subject:   RE: Kernel Panic during install with 4.8 mini ISO
Message-ID:  <BLEJJPHBPJJLNFDIHIDCKEBJCAAA.chris.p.ward@ntlworld.com>
In-Reply-To: <E19OAsy-0005F7-1v@claygirl.org>

next in thread | previous in thread | raw e-mail | index | archive | help
Thanks Yussef, that's done the job.

Chris.

-----Original Message-----
From: owner-freebsd-questions@freebsd.org
[mailto:owner-freebsd-questions@freebsd.org]On Behalf Of yussef
Sent: 06 June 2003 07:40
To: freebsd-questions@freebsd.org
Subject: Re: Kernel Panic during install with 4.8 mini ISO

before the kernel is loaded, when you're given 10 seconds, hit any key
besides enter, then type 'set hw.pcic.intr_path=1' without the quotes.
good luck. hope this works.

yussef

On Thu, 5 Jun 2003 22:11:18 +0100
"Chris Ward" <chris.p.ward@ntlworld.com> wrote:

> I'm seeing a kernel panic during boot of 4.8 mini ISO install CD,
> details below.
>
> Fault virtual addr = 0xeb902
> Fault code = supervisor read, page not present
> Instr Ptr = 0x8:0xc00eb807
> Stack Ptr = 0x10:0xc0843d6c
> Frame Ptr = 0x10:0xc0843d6c
> Code Seg = base 0x0, limit 0xfffff, type 0x1b, DPL0, pres 1, def32 1,
> gran 1 Proc eflags = interrupt enabled, resume, IOPL=0
> Current proc = 0 (swapper)
> IRQ mask = net tty bio cam
> Trap no = 12
>
> Just prior to this it was probing the VGA:
>
> pcio0: <unknown card> (vendor = 0x1039, dev = 0x7013) at 1.6 irq 10
> pcib2: <PCI to PCI bridge (vendor = 1039, device = 0001)> at device
> 2.0 on pci0
> pci1: <PCI bus> on pcib2
> pci1: <SIS model 6300 VGA-compatible display device> at 0.0
> pci_cfgintr_virgin: using routable interrupt 3
>
> <Kernel panic follows...>
>
> The kernel is unmodified from that of the ISO image.
>
> I'm guessing that I need to pass in some params to init the graphics
> card but being new to FreeBSD I'm not sure how to do this.
>
> Could somebody please point me in the right direction?
>
> Thx.
> Chris.
>
>
>
> _______________________________________________
> freebsd-questions@freebsd.org mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-questions
> To unsubscribe, send any mail to
> "freebsd-questions-unsubscribe@freebsd.org"
>


_______________________________________________
freebsd-questions@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-questions
To unsubscribe, send any mail to "freebsd-questions-unsubscribe@freebsd.org"




Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?BLEJJPHBPJJLNFDIHIDCKEBJCAAA.chris.p.ward>