Date: Wed, 19 Sep 2001 14:01:26 -0700 (PDT) From: "Matthew T. Lager" <mlager@srvr1.lynxcom.net> To: Kenneth Wayne Culver <culverk@wam.umd.edu> Cc: <freebsd-questions@FreeBSD.ORG> Subject: Re: NATD Problem... Message-ID: <Pine.GSO.4.33.0109191401120.2334-100000@srvr1.lynxcom.net> In-Reply-To: <Pine.GSO.4.21.0109191658490.5353-100000@rac1.wam.umd.edu>
next in thread | previous in thread | raw e-mail | index | archive | help
Ok, thank you for the help! I appreciate it. Sincerly, Matt On Wed, 19 Sep 2001, Kenneth Wayne Culver wrote: > Usually, you connect the interface that you want to go to the outside > world directly to the outside world, not through the hub, then you connect > the internal network interface to the hub or switch. > > Ken > > On Wed, 19 Sep 2001, Matthew T. Lager wrote: > > > Each interface must be hooked into different hubs? Must these hubs be > > complete seperate? > > > > On Wed, 19 Sep 2001, Kenneth Wayne Culver wrote: > > > > > You probably have both interfaces hooked to the same hub or switch > > > > > > Ken > > > > > > On Wed, 19 Sep 2001, Matthew T. Lager wrote: > > > > > > > I just installed a fresh version of FreeBSD 4.4RC5 on an Intel machine. I > > > > configured NATD. The setup is as follows: > > > > > > > > KERNEL: > > > > options IPFIREWALL > > > > options IPDIVERT > > > > > > > > /etc/rc.conf: > > > > gateway_enable="YES" > > > > firewall_enable="YES" > > > > firewall_type="OPEN" > > > > natd_enable="YES" > > > > natd_interface="xl0" > > > > natd_flags="" > > > > > > > > ifconfig -a: > > > > xl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 > > > > inet6 fe80::250:4ff:fe6c:daa7%xl0 prefixlen 64 scopeid 0x1 > > > > inet 204.210.40.137 netmask 0xffffff00 broadcast 255.255.255.255 > > > > ether 00:50:04:6c:da:a7 > > > > media: Ethernet 10baseT/UTP (10baseT/UTP <half-duplex>) > > > > > > > > ep0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 > > > > inet 192.168.0.1 netmask 0xffffff00 broadcast 192.168.0.255 > > > > inet6 fe80::220:afff:fe12:a929%ep0 prefixlen 64 scopeid 0x2 > > > > ether 00:20:af:12:a9:29 > > > > media: Ethernet 10baseT/UTP > > > > > > > > The true internet IP address is on xl0 and the LAN IP address is on ep0. > > > > NATD functions fine, but I receive hundreds and hundreds of error messages > > > > in my logfile: > > > > > > > > Sep 19 06:48:46 firewall /kernel: arp: 192.168.0.101 is on ep0 but got > > > > reply from 00:01:03:e6:a4:d5 on xl0 > > > > Sep 19 06:48:47 firewall /kernel: arp: 204.210.40.1 is on xl0 but got > > > > reply from 08:00:3e:07:07:ab on ep0 > > > > Sep 19 06:49:18 firewall last message repeated 20 times > > > > Sep 19 06:51:19 firewall last message repeated 63 times > > > > Sep 19 07:01:20 firewall last message repeated 290 times > > > > Sep 19 01:57:56 firewall /kernel: arp: 192.168.0.100 is on ep0 but got > > > > reply from 00:02:e3:08:49:d8 on xl0 > > > > > > > > and so on. What the heck is wrong? Thanks! > > > > > > > > Matt Lager > > > > mlager@lynxcom.net > > > > > > > > > > > > To Unsubscribe: send mail to majordomo@FreeBSD.org > > > > with "unsubscribe freebsd-questions" in the body of the message > > > > > > > > > > > > > > > > To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.GSO.4.33.0109191401120.2334-100000>