Date: Sun, 13 Apr 2008 09:17:31 +1000 From: Da Rock <rock_on_the_web@comcen.com.au> To: freebsd-questions@freebsd.org Subject: Re: Printer getting attached to umass and da Message-ID: <1208042251.16346.218.camel@laptop2.herveybayaustralia.com.au> In-Reply-To: <200804121833.18007.freebsd@insightbb.com> References: <200804121536.17761.freebsd@insightbb.com> <200804121655.37036.freebsd@insightbb.com> <48012A69.1010205@math.arizona.edu> <200804121833.18007.freebsd@insightbb.com>
next in thread | previous in thread | raw e-mail | index | archive | help
On Sat, 2008-04-12 at 18:33 -0400, Steven Friedrich wrote: > On Saturday 12 April 2008 05:32:25 pm Predrag Punosevac wrote: > > Steven Friedrich wrote: > > > On Saturday 12 April 2008 04:29:20 pm Warren Block wrote: > > >> On Sat, 12 Apr 2008, Steven Friedrich wrote: > > >>> From messages: > > >>> messages:Apr 12 09:39:55 laptop kernel: ulpt0: <EPSON USB2.0 > > >>> MFP(Hi-Speed), class 0/0, rev 2.00/1.00, addr 2> on uhub4 > > >>> messages:Apr 12 09:39:55 laptop kernel: umass0: <EPSON USB2.0 > > >>> MFP(Hi-Speed), class 0/0, rev 2.00/1.00, addr 2> on uhub4 > > >>> messages:Apr 12 09:39:55 laptop kernel: da0: <EPSON Stylus Storage > > >>> 1.00> Removable Direct Access SCSI-2 device > > >>> > > >>> Why is it getting attached to umass and da? > > >> > > >> Most likely the printer has memory card slots that are accessible via > > >> USB. > > >> > > >>> Should I config something to stop this? > > >> > > >> Not unless it's causing a problem. > > >> > > >> -Warren Block * Rapid City, South Dakota USA > > > > > > It does have slots for memory... > > > I can't get this printer to work, and the cups error_log shows no errors. > > > I had been reading a HOW-TO on the CUPS site and I set the loglevel to > > > debug, figuring I'd get a message about a broken pipe due to a missing > > > filter. No such luck. Far as CUPS is concerned, it's working. But it only > > > feeds sheet after sheet and occasionally prints garbage. > > > I've tried CUPS test page and a one sheet doc from KATE. > > > The gutenprint doc says I should have an Epson backend > > > in /usr/lib/cups/backend (but I think on freebsd it will be > > > in /usr/local/libexec/cups/backend). > > > But it's not there... > > > _______________________________________________ > > > freebsd-questions@freebsd.org mailing list > > > http://lists.freebsd.org/mailman/listinfo/freebsd-questions > > > To unsubscribe, send any mail to > > > "freebsd-questions-unsubscribe@freebsd.org" > > > > Remove the umass driver from the kernel (you have to recompile) and then > > configure printer. Then load > > umass driver after the boot with kldload utility since otherwise you > > will not be able to use Floppy disk and USB sticks > > > > Cheers, > > Predrag > > Thanks for the suggestion, but after removing the umass driver, the printer > still dosen't work. > I did verify with usbdevs -dv that umass is not attached to the printer > anymore... I'd say you better find a way to get that Epson backend installed- not much else is going to make a difference here.
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?1208042251.16346.218.camel>