Date: Fri, 24 Feb 2006 17:56:59 -0500 (EST) From: Wesley Morgan <morganw@chemikals.org> To: freebsd-amd64@freebsd.org Subject: Re: Kernel Freezes Message-ID: <20060224175539.H5959@volatile.chemikals.org> In-Reply-To: <20060224133404.G780@volatile.chemikals.org> References: <20060224133404.G780@volatile.chemikals.org>
next in thread | previous in thread | raw e-mail | index | archive | help
On Fri, 24 Feb 2006, Wesley Morgan wrote:
> I'm in the process of upgrading to an amd64 machine, and have run into
> some problems. The system is a Sempron 2600+ running in an ABIT KV-85
> board, with 1gb of ram and a Maxtor 300gb SATA drive.
>
> So far, I was able to install both 6.1-beta2 and 6.0 without a problem.
> The system boots fine and seems to idle fine (at least, it idled all
> last night). The problem occurs when I try to compile something -- a
> custom kernel, buildworld, a couple ports -- the system freezes solid,
> with a garbled video display. The network driver doesn't seem to be the
> problem. I've disabled practically everything I can in the BIOS and I've
> even installed an old PCI video card, all with the same result.
>
> Trying to boot a 5.4 kernel was unsuccessful, the system froze during
> device detection, although I am not sure where as the screen became
> unreadable. I'll have to try a serial console later.
>
> Unfortunately I don't have the dmesg output handy ATM, but I wanted to
> know if this problem tickled anyone's brain for a possible answer...
> I'll post the boot logs later.
The boot logs from said system. Anything stand out? The system passes a
256MB 10-loop memtest as well, so RAM doesn't seem the likely culprit.
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 6.0-RELEASE #0: Wed Nov 2 19:07:38 UTC 2005
root@rat.samsco.home:/usr/obj/usr/src/sys/GENERIC
Preloaded elf kernel "/boot/kernel/kernel" at 0xffffffff80972000.
ACPI APIC Table: <VIAK8M AWRDACPI>
Calibrating clock(s) ... i8254 clock: 1193177 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 1599827782 Hz
CPU: AMD Sempron(tm) Processor 2600+ (1599.83-MHz K8-class CPU)
Origin = "AuthenticAMD" Id = 0x20fc2 Stepping = 2
Features=0x78bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2>
Features2=0x1<SSE3>
AMD Features=0xe2500800<SYSCALL,NX,MMX+,<b25>,LM,3DNow+,3DNow>
L1 2MB data TLB: 8 entries, fully associative
L1 2MB instruction TLB: 8 entries, fully associative
L1 4KB data TLB: 32 entries, fully associative
L1 4KB instruction TLB: 32 entries, fully associative
L1 data cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
L1 instruction cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
L2 2MB unified TLB: 0 entries, disabled/not present
L2 4KB data TLB: 512 entries, 4-way associative
L2 4KB instruction TLB: 512 entries, 4-way associative
L2 unified cache: 128 kbytes, 64 bytes/line, 1 lines/tag, 16-way associative
real memory = 1006567424 (959 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
0x0000000000a6f000 - 0x000000003a38ffff, 965873664 bytes (235809 pages)
avail memory = 960376832 (915 MB)
APIC: CPU 0 has ACPI ID 0
MADT: Found IO APIC ID 2, Interrupt 0 at 0xfec00000
ioapic0: Routing external 8259A's -> intpin 0
ioapic0: intpin 0 -> ExtINT (edge, high)
ioapic0: intpin 1 -> ISA IRQ 1 (edge, high)
ioapic0: intpin 2 -> ISA IRQ 2 (edge, high)
ioapic0: intpin 3 -> ISA IRQ 3 (edge, high)
ioapic0: intpin 4 -> ISA IRQ 4 (edge, high)
ioapic0: intpin 5 -> ISA IRQ 5 (edge, high)
ioapic0: intpin 6 -> ISA IRQ 6 (edge, high)
ioapic0: intpin 7 -> ISA IRQ 7 (edge, high)
ioapic0: intpin 8 -> ISA IRQ 8 (edge, high)
ioapic0: intpin 9 -> ISA IRQ 9 (edge, high)
ioapic0: intpin 10 -> ISA IRQ 10 (edge, high)
ioapic0: intpin 11 -> ISA IRQ 11 (edge, high)
ioapic0: intpin 12 -> ISA IRQ 12 (edge, high)
ioapic0: intpin 13 -> ISA IRQ 13 (edge, high)
ioapic0: intpin 14 -> ISA IRQ 14 (edge, high)
ioapic0: intpin 15 -> ISA IRQ 15 (edge, high)
ioapic0: intpin 16 -> PCI IRQ 16 (level, low)
ioapic0: intpin 17 -> PCI IRQ 17 (level, low)
ioapic0: intpin 18 -> PCI IRQ 18 (level, low)
ioapic0: intpin 19 -> PCI IRQ 19 (level, low)
ioapic0: intpin 20 -> PCI IRQ 20 (level, low)
ioapic0: intpin 21 -> PCI IRQ 21 (level, low)
ioapic0: intpin 22 -> PCI IRQ 22 (level, low)
ioapic0: intpin 23 -> PCI IRQ 23 (level, low)
MADT: Interrupt override: source 0, irq 2
ioapic0: Routing IRQ 0 -> intpin 2
ioapic0: intpin 2 trigger: edge
ioapic0: intpin 2 polarity: high
MADT: Interrupt override: source 9, irq 9
ioapic0: intpin 9 trigger: level
ioapic0: intpin 9 polarity: low
lapic0: Routing NMI -> LINT1
lapic0: LINT1 trigger: edge
lapic0: LINT1 polarity: high
ioapic0 <Version 0.3> irqs 0-23 on motherboard
cpu0 BSP:
ID: 0x00000000 VER: 0x00050010 LDR: 0x01000000 DFR: 0x0fffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000100ef therm: 0x00010000 err: 0x00010000 pcm: 0x00010000
wlan: <802.11 Link Layer>
null: <null device, zero device>
random: <entropy source, Software, Yarrow>
nfslock: pseudo-device
mem: <memory>
io: <I/O>
acpi0: <VIAK8M AWRDACPI> on motherboard
acpi0: [MPSAFE]
pci_open(1): mode 1 addr port (0x0cf8) is 0x80007804
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=80] is there (id=02041106)
AcpiOsDerivePciId: bus 0 dev 17 func 0
AcpiOsDerivePciId: bus 0 dev 15 func 1
AcpiOsDerivePciId: bus 0 dev 17 func 1
AcpiOsDerivePciId: bus 0 dev 15 func 0
AcpiOsDerivePciId: bus 0 dev 17 func 2
AcpiOsDerivePciId: bus 0 dev 17 func 3
AcpiOsDerivePciId: bus 0 dev 17 func 4
AcpiOsDerivePciId: bus 0 dev 16 func 0
AcpiOsDerivePciId: bus 0 dev 16 func 1
AcpiOsDerivePciId: bus 0 dev 16 func 2
AcpiOsDerivePciId: bus 0 dev 16 func 3
AcpiOsDerivePciId: bus 0 dev 16 func 4
AcpiOsDerivePciId: bus 0 dev 17 func 0
acpi0: Power Button (fixed)
pci_link0: <ACPI PCI Link LNKA> irq 10 on acpi0
pci_link0: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 10 N 0 3 4 6 7 10 11 12
pci_link0: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 10 N 0 3 4 6 7 10 11 12
pci_link0: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 6 7 10 11 12
pci_link1: <ACPI PCI Link LNKB> irq 11 on acpi0
pci_link1: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 11 N 0 3 4 6 7 10 11 12
pci_link1: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 11 N 0 3 4 6 7 10 11 12
pci_link1: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 6 7 10 11 12
pci_link2: <ACPI PCI Link LNKC> irq 12 on acpi0
pci_link2: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 12 N 0 3 4 6 7 10 11 12
pci_link2: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 12 N 0 3 4 6 7 10 11 12
pci_link2: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 6 7 10 11 12
pci_link3: <ACPI PCI Link LNKD> on acpi0
pci_link3: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 6 7 10 11 12
pci_link3: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 6 7 10 11 12
pci_link3: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 6 7 10 11 12
pci_link4: <ACPI PCI Link LNKE> on acpi0
pci_link4: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 6 7 10 11 12
pci_link4: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 6 7 10 11 12
pci_link4: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 6 7 10 11 12
pci_link5: <ACPI PCI Link LNKF> on acpi0
pci_link5: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 6 7 10 11 12
pci_link5: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 6 7 10 11 12
pci_link5: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 6 7 10 11 12
pci_link6: <ACPI PCI Link LNK0> on acpi0
pci_link6: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 6 7 10 11 12
pci_link6: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 6 7 10 11 12
pci_link6: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 6 7 10 11 12
pci_link7: <ACPI PCI Link LNK1> on acpi0
pci_link7: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 6 7 10 11 12
pci_link7: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 6 7 10 11 12
pci_link7: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 6 7 10 11 12
pci_link8: <ACPI PCI Link ALKA> irq 20 on acpi0
pci_link8: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 20 N 0 20
pci_link8: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 20 N 0 20
pci_link8: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 20
pci_link9: <ACPI PCI Link ALKB> irq 21 on acpi0
pci_link9: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 21 N 0 21
pci_link9: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 21 N 0 21
pci_link9: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 21
pci_link10: <ACPI PCI Link ALKC> irq 22 on acpi0
pci_link10: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 22 N 0 22
pci_link10: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 22 N 0 22
pci_link10: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 22
pci_link11: <ACPI PCI Link ALKD> irq 23 on acpi0
pci_link11: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 23 N 0 23
pci_link11: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 23 N 0 23
pci_link11: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 23
ACPI timer: 1/2 1/1 1/2 1/2 1/2 1/2 1/2 1/1 1/2 1/1 -> 10
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
ACPI: Found matching pin for 0.16.INTA at func 0: 255
ACPI: Found matching pin for 0.16.INTA at func 1: 255
ACPI: Found matching pin for 0.16.INTB at func 2: 255
ACPI: Found matching pin for 0.16.INTB at func 3: 255
ACPI: Found matching pin for 0.16.INTC at func 4: 255
ACPI: Found matching pin for 0.17.INTC at func 5: 12
pci_link10: BIOS IRQ 12 for -2145774616.17.INTC is invalid
ACPI: Found matching pin for 0.18.INTA at func 0: 10
pci_link11: BIOS IRQ 10 for -2145774616.18.INTA is invalid
ACPI: Found matching pin for 0.15.INTA at func 1: 255
ACPI: Found matching pin for 0.15.INTB at func 0: 11
pci_link8: BIOS IRQ 11 for -2145774616.15.INTB is invalid
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
found-> vendor=0x1106, dev=0x0204, revid=0x00
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0006, statreg=0x2230, cachelnsz=0 (dwords)
lattimer=0x08 (240 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
map[10]: type 3, range 32, base e0000000, size 27, enabled
found-> vendor=0x1106, dev=0x1204, revid=0x00
bus=0, slot=0, func=1
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1106, dev=0x2204, revid=0x00
bus=0, slot=0, func=2
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1106, dev=0x3204, revid=0x00
bus=0, slot=0, func=3
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1106, dev=0x4204, revid=0x00
bus=0, slot=0, func=4
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1106, dev=0x7204, revid=0x00
bus=0, slot=0, func=7
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1106, dev=0xb188, revid=0x00
bus=0, slot=1, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x0230, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x0e (3500 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1106, dev=0x3149, revid=0x80
bus=0, slot=15, func=0
class=01-01-8f, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=11
powerspec 2 supports D0 D3 current D0
map[10]: type 4, range 32, base 0000b000, size 3, enabled
map[14]: type 4, range 32, base 0000b400, size 2, enabled
map[18]: type 4, range 32, base 0000b800, size 3, enabled
map[1c]: type 4, range 32, base 0000bc00, size 2, enabled
map[20]: type 4, range 32, base 0000c000, size 4, enabled
map[24]: type 4, range 32, base 0000c400, size 8, enabled
pcib0: matched entry for 0.15.INTB (src \\_SB_.PCI0.ALKA:0)
pcib0: slot 15 INTB routed to irq 20 via \\_SB_.PCI0.ALKA
found-> vendor=0x1106, dev=0x0571, revid=0x06
bus=0, slot=15, func=1
class=01-01-8a, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=255
powerspec 2 supports D0 D3 current D0
map[20]: type 4, range 32, base 0000c800, size 4, enabled
found-> vendor=0x1106, dev=0x3038, revid=0x81
bus=0, slot=16, func=0
class=0c-03-00, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=255
powerspec 2 supports D0 D1 D2 D3 current D0
map[20]: type 4, range 32, base 0000cc00, size 5, enabled
found-> vendor=0x1106, dev=0x3038, revid=0x81
bus=0, slot=16, func=1
class=0c-03-00, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=255
powerspec 2 supports D0 D1 D2 D3 current D0
map[20]: type 4, range 32, base 0000d000, size 5, enabled
found-> vendor=0x1106, dev=0x3038, revid=0x81
bus=0, slot=16, func=2
class=0c-03-00, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=255
powerspec 2 supports D0 D1 D2 D3 current D0
map[20]: type 4, range 32, base 0000d400, size 5, enabled
found-> vendor=0x1106, dev=0x3038, revid=0x81
bus=0, slot=16, func=3
class=0c-03-00, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=255
powerspec 2 supports D0 D1 D2 D3 current D0
map[20]: type 4, range 32, base 0000d800, size 5, enabled
found-> vendor=0x1106, dev=0x3104, revid=0x86
bus=0, slot=16, func=4
class=0c-03-20, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=c, irq=255
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base ee000000, size 8, enabled
found-> vendor=0x1106, dev=0x3227, revid=0x00
bus=0, slot=17, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x0087, statreg=0x0210, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
found-> vendor=0x1106, dev=0x3059, revid=0x60
bus=0, slot=17, func=5
class=04-01-00, hdrtype=0x00, mfdev=0
cmdreg=0x0001, statreg=0x0210, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=c, irq=12
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 4, range 32, base 0000dc00, size 8, enabled
pcib0: matched entry for 0.17.INTC (src \\_SB_.PCI0.ALKC:0)
pcib0: slot 17 INTC routed to irq 22 via \\_SB_.PCI0.ALKC
found-> vendor=0x1106, dev=0x3065, revid=0x78
bus=0, slot=18, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x03 (750 ns), maxlat=0x08 (2000 ns)
intpin=a, irq=10
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 4, range 32, base 0000e400, size 8, enabled
map[14]: type 1, range 32, base ee001000, size 8, enabled
pcib0: matched entry for 0.18.INTA (src \\_SB_.PCI0.ALKD:0)
pcib0: slot 18 INTA routed to irq 23 via \\_SB_.PCI0.ALKD
found-> vendor=0x1022, dev=0x1100, revid=0x00
bus=0, slot=24, func=0
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0010, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1022, dev=0x1101, revid=0x00
bus=0, slot=24, func=1
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1022, dev=0x1102, revid=0x00
bus=0, slot=24, func=2
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1022, dev=0x1103, revid=0x00
bus=0, slot=24, func=3
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
agp0: <VIA 8380 host to PCI bridge> mem 0xe0000000-0xe7ffffff at device 0.0 on pci0
AMD64: 1 Misc. Control unit(s) found.
agp0: Reserved 0x8000000 bytes for rid 0x10 type 3 at 0xe0000000
agp0: allocating GATT for aperture of size 128M
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0xf000-0xfff
pcib1: memory decode 0xec000000-0xedffffff
pcib1: prefetched decode 0xe8000000-0xebffffff
pci1: <PCI bus> on pcib1
pci1: physical bus=1
found-> vendor=0x1106, dev=0x3108, revid=0x01
bus=1, slot=0, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0230, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x02 (500 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 3, range 32, base e8000000, size 26, enabled
pcib1: (null) requested memory range 0xe8000000-0xebffffff: good
map[14]: type 1, range 32, base ec000000, size 24, enabled
pcib1: (null) requested memory range 0xec000000-0xecffffff: good
pcib0: matched entry for 0.1.INTA
pcib0: slot 1 INTA hardwired to IRQ 16
pcib1: slot 0 INTA is routed to irq 16
pci1: <display, VGA> at device 0.0 (no driver attached)
atapci0: <VIA 6420 SATA150 controller> port 0xb000-0xb007,0xb400-0xb403,0xb800-0xb807,0xbc00-0xbc03,0xc000-0xc00f,0xc400-0xc4ff irq 20 at device 15.0 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xc000
atapci0: [MPSAFE]
atapci0: Reserved 0x100 bytes for rid 0x24 type 4 at 0xc400
ata2: <ATA channel 0> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0xb000
atapci0: Reserved 0x4 bytes for rid 0x14 type 4 at 0xb400
ata2: SATA connect ready time=0ms
ata2: sata_connect devices=0x1<ATA_MASTER>
ata2: [MPSAFE]
ata3: <ATA channel 1> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0xb800
atapci0: Reserved 0x4 bytes for rid 0x1c type 4 at 0xbc00
ata3: SATA connect status=00000000
ata3: [MPSAFE]
atapci1: <VIA 8237 UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xc800-0xc80f at device 15.1 on pci0
atapci1: Reserved 0x10 bytes for rid 0x20 type 4 at 0xc800
ata0: <ATA channel 0> on atapci1
atapci1: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci1: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=7f ostat1=50
ata0: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
ata0: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
ata0: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
ata0: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
ata0: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
ata0: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
ata0: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
ata0: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
ata0: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
ata0: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
ata0: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
ata0: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
ata0: stat1=0x10 err=0x01 lsb=0x14 msb=0xeb
ata0: reset tp2 stat0=ff stat1=10 devices=0x8<ATAPI_SLAVE>
ata0: [MPSAFE]
ata1: <ATA channel 1> on atapci1
atapci1: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci1: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=03 ostat0=60 ostat1=70
ata1: stat0=0x20 err=0x20 lsb=0x20 msb=0x20
ata1: stat1=0x30 err=0x30 lsb=0x30 msb=0x30
ata1: reset tp2 stat0=20 stat1=30 devices=0x0
ata1: [MPSAFE]
uhci0: <VIA 83C572 USB controller> port 0xcc00-0xcc1f at device 16.0 on pci0
uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0xcc00
pcib0: matched entry for 0.16.INTA (src \\_SB_.PCI0.ALKB:0)
pcib0: slot 16 INTA routed to irq 21 via \\_SB_.PCI0.ALKB
uhci0: [GIANT-LOCKED]
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <VIA 83C572 USB controller> port 0xd000-0xd01f at device 16.1 on pci0
uhci1: Reserved 0x20 bytes for rid 0x20 type 4 at 0xd000
pcib0: matched entry for 0.16.INTA (src \\_SB_.PCI0.ALKB:0)
pcib0: slot 16 INTA routed to irq 21 via \\_SB_.PCI0.ALKB
uhci1: [GIANT-LOCKED]
usb1: <VIA 83C572 USB controller> on uhci1
usb1: USB revision 1.0
uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <VIA 83C572 USB controller> port 0xd400-0xd41f at device 16.2 on pci0
uhci2: Reserved 0x20 bytes for rid 0x20 type 4 at 0xd400
pcib0: matched entry for 0.16.INTB (src \\_SB_.PCI0.ALKB:0)
pcib0: slot 16 INTB routed to irq 21 via \\_SB_.PCI0.ALKB
uhci2: [GIANT-LOCKED]
usb2: <VIA 83C572 USB controller> on uhci2
usb2: USB revision 1.0
uhub2: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3: <VIA 83C572 USB controller> port 0xd800-0xd81f at device 16.3 on pci0
uhci3: Reserved 0x20 bytes for rid 0x20 type 4 at 0xd800
pcib0: matched entry for 0.16.INTB (src \\_SB_.PCI0.ALKB:0)
pcib0: slot 16 INTB routed to irq 21 via \\_SB_.PCI0.ALKB
uhci3: [GIANT-LOCKED]
usb3: <VIA 83C572 USB controller> on uhci3
usb3: USB revision 1.0
uhub3: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
ehci0: <VIA VT6202 USB 2.0 controller> mem 0xee000000-0xee0000ff at device 16.4 on pci0
ehci0: Reserved 0x100 bytes for rid 0x10 type 3 at 0xee000000
pcib0: matched entry for 0.16.INTC (src \\_SB_.PCI0.ALKB:0)
pcib0: slot 16 INTC routed to irq 21 via \\_SB_.PCI0.ALKB
ehci0: [GIANT-LOCKED]
usb4: EHCI version 1.0
usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3
usb4: <VIA VT6202 USB 2.0 controller> on ehci0
usb4: USB revision 2.0
uhub4: VIA EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
isab0: <PCI-ISA bridge> at device 17.0 on pci0
isa0: <ISA bus> on isab0
pci0: <multimedia, audio> at device 17.5 (no driver attached)
vr0: <VIA VT6102 Rhine II 10/100BaseTX> port 0xe400-0xe4ff mem 0xee001000-0xee0010ff irq 23 at device 18.0 on pci0
vr0: Reserved 0x100 bytes for rid 0x10 type 4 at 0xe400
miibus0: <MII bus> on vr0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0: OUI 0x004063, model 0x0032, rev. 10
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
vr0: bpf attached
vr0: Ethernet address: 00:50:8d:84:b2:51
vr0: [MPSAFE]
acpi_tz0: <Thermal Zone> on acpi0
fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: ic_type 90 part_id 80
fdc0: [MPSAFE]
fdc0: [FAST]
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: irq maps: 0x4041 0x4041 0x4041 0x4041
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
ppc0: using extended I/O port range
ppc0: ECP SPP SPP
ppc0: <ECP parallel printer port> port 0x378-0x37f,0x778-0x77b irq 7 drq 3 on acpi0
ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/16 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
plip0: bpf attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x1d0000
atkbd0: [GIANT-LOCKED]
psm0: unable to allocate IRQ
ex_isa_identify()
atkbdc: atkbdc0 already exists; skipping it
ppc: ppc0 already exists; skipping it
sio: sio0 already exists; skipping it
pnp_identify: Trying Read_Port at 203
pnp_identify: Trying Read_Port at 243
pnp_identify: Trying Read_Port at 283
pnp_identify: Trying Read_Port at 2c3
pnp_identify: Trying Read_Port at 303
pnp_identify: Trying Read_Port at 343
pnp_identify: Trying Read_Port at 383
pnp_identify: Trying Read_Port at 3c3
PNP Identify complete
ahc_isa_probe 11: ioport 0xbc00 alloc failed
ahc_isa_probe 12: ioport 0xcc00 alloc failed
ahc_isa_probe 13: ioport 0xdc00 alloc failed
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
isa_probe_children: probing PnP devices
Device configuration finished.
procfs registered
linprocfs registered
lapic: Divisor 2, Frequency 99989114 hz
Timecounter "TSC" frequency 1599827782 Hz quality 800
Timecounters tick every 1.000 msec
Linux ELF exec handler installed
lo0: bpf attached
ata0-slave: pio=PIO4 wdma=WDMA2 udma=UDMA33 cable=40 wire
acd0: setting PIO4 on VIA 8237 chip
acd0: setting UDMA33 on VIA 8237 chip
fdc0: output ready timeout
fdc0: output ready timeout
fdc0: output ready timeout
fdc0: output ready timeout
fdc0: output ready timeout
fdc0: output ready timeout
fdc0: output ready timeout
acd0: <CREATIVE DVD-ROM DVD1610E/GCH4> DVDROM drive at ata0 as slave
acd0: 512KB buffer, UDMA33
acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, packet
acd0: Writes:
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
ata0-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire
ad4: 286188MB <Maxtor 7L300S0 BANC1G10> at ata2-master SATA150
ad4: 586114704 sectors [581463C/16H/63S] 16 sectors/interrupt 1 depth queue
GEOM: new disk ad4
ad4: VIA check1 failed
ad4: Adaptec check1 failed
ad4: LSI (v3) check1 failed
ad4: LSI (v2) check1 failed
ad4: FreeBSD check1 failed
ATA PseudoRAID loaded
ioapic0: routing intpin 1 (ISA IRQ 1) to cluster 0
ioapic0: routing intpin 4 (ISA IRQ 4) to cluster 0
ioapic0: routing intpin 6 (ISA IRQ 6) to cluster 0
ioapic0: routing intpin 7 (ISA IRQ 7) to cluster 0
ioapic0: routing intpin 9 (ISA IRQ 9) to cluster 0
ioapic0: routing intpin 14 (ISA IRQ 14) to cluster 0
ioapic0: routing intpin 15 (ISA IRQ 15) to cluster 0
ioapic0: routing intpin 20 (PCI IRQ 20) to cluster 0
ioapic0: routing intpin 21 (PCI IRQ 21) to cluster 0
ioapic0: routing intpin 23 (PCI IRQ 23) to cluster 0
Trying to mount root from ufs:/dev/ad4s1a
start_init: trying /sbin/init
--
This .signature sanitized for your protection
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20060224175539.H5959>