Skip site navigation (1)Skip section navigation (2)
Date:      Sun, 3 Sep 2017 08:35:31 +0930
From:      "Priyadarshana Chandrasena" <vpc@ulka.com.au>
To:        "'Mark Saad'" <nonesuch@longcount.org>, <sthaug@nethelp.no>
Cc:        <rainer@ultra-secure.de>, <FreeBSD-stable@FreeBSD.org>
Subject:   RE: HP Smart array P440 support
Message-ID:  <000001d3243f$ff2d3a10$fd87ae30$@ulka.com.au>
In-Reply-To: <02C1D059-24AD-4114-BBF6-ECB443DC49E1@longcount.org>
References:  <001501d323f2$3e517560$baf46020$@ulka.com.au> <3D731E17-CB4B-495E-8D9E-6614BD3D919E@ultra-secure.de> <20170902.174119.74668153.sthaug@nethelp.no> <02C1D059-24AD-4114-BBF6-ECB443DC49E1@longcount.org>

Next in thread | Previous in thread | Raw E-Mail | Index | Archive | Help
I will try to install 10.3 and thanks for your comments and help.
Regards,
Chandrasena

-----Original Message-----
From: Mark Saad [mailto:nonesuch@longcount.org]=20
Sent: Sunday, 3 September 2017 3:56 AM
To: sthaug@nethelp.no
Cc: vpc@ulka.com.au; rainer@ultra-secure.de; FreeBSD-stable@FreeBSD.org
Subject: Re: HP Smart array P440 support

All
Also don't forget to is install cciss_vol_status to monitor the array .

---
Mark Saad | nonesuch@longcount.org

On Sep 2, 2017, at 11:41 AM, sthaug@nethelp.no wrote:

>>> I have HP DL20 Gen 9 server. But I can not install FreeBSD 10.2 in=20
>>> it. I have a HP smart array P440 in my server. I can not find out=20
>>> anywhere if ciss driver support include HP Gen 9 storage=20
>>> controllers.  Could you please update the ciss driver in 10.3?
>>=20
>> Try 10.3
>>=20
>> I know the release-notes say nothing about it, but I believe it is
supported.
>>=20
>> If not that, 11.0 surely does (even though the release-notes=20
>> don=1B$,1ry=1B(Bt mention it, either)
>=20
> I can confirm that 10.3 supports the P440 controller. From a DL360=20
> Gen9 server running 10.3 here:
>=20
> ciss0: <HP Smart Array P440ar> port 0x2000-0x20ff mem=20
> 0x92c00000-0x92cfffff,0x92d00000-0x92d003ff irq 16 at device 0.0 on=20
> pci3
> ciss0: PERFORMANT Transport
> ...
> da0 at ciss0 bus 0 scbus0 target 0 lun 0
> da0: <HP RAID 1(1+0) OK> Fixed Direct Access SPC-3 SCSI device
> da0: Serial Number PDNLH0BRH8S3RF
> da0: 135.168MB/s transfers
> da0: Command Queueing enabled
> da0: 139979MB (286677120 512 byte sectors)
>=20
> Steinar Haug, Nethelp consulting, sthaug@nethelp.no=20
> _______________________________________________
> freebsd-stable@freebsd.org mailing list=20
> https://lists.freebsd.org/mailman/listinfo/freebsd-stable
> To unsubscribe, send any mail to =
"freebsd-stable-unsubscribe@freebsd.org"





Want to link to this message? Use this URL: <http://docs.FreeBSD.org/cgi/mid.cgi?000001d3243f$ff2d3a10$fd87ae30$>