Date: Wed, 17 Aug 2011 15:35:09 +0200 From: Miroslav Lachman <000.fbsd@quip.cz> To: freebsd-stable@freebsd.org Subject: can not boot from RAIDZ with 8-STABLE Message-ID: <4E4BC38D.1050808@quip.cz>
next in thread | raw e-mail | index | archive | help
I tried mfsBSD installation on Dell T110 with PERC H200A and 4x 500GB
SATA disks. If I create zpool with RAIDZ, the boot immediately hangs
with following error:
ZFS: i/o error - all block copies unavailable
ZFS: can't read MOS
ZFS: unexpected object set type 0
ZFS: unexpected object set type 0
FreeBSD/x86 boot
Default: tank0:/boot/kernel/kernel
boot:
ZFS: unexpected object set type 0
FreeBSD/x86 boot
Default: tank0:/boot/kernel/kernel
boot:
The system is FreeBSD 8.2-STABLE #0: Sat Aug 13 20:33:31 CEST 2011
GENERIC amd64
Built from sources from Aug 13 2011.
Identical system is booting fine from external (USB) drive and I can use
data on zpool RAIDZ tank0 without any problems.
So the pool and disks are fine, only boot failed.
Disks (da0 - da3) are using GPT:
=> 34 976773101 da0 GPT (465G)
34 128 1 freebsd-boot (64k)
162 8388608 2 freebsd-swap (4.0G)
8388770 964689920 3 freebsd-zfs (460G)
973078690 3694445 - free - (1.8G)
I also tried to create the pool manually instead of script from mfsBSD,
but the result is the same.
This was my manual method:
gpart create -s GPT da0
gpart add -b 34 -s 128 -t freebsd-boot da0
gpart add -s 4g -t freebsd-swap -l swap0 da0
gpart add -s 460g -t freebsd-zfs -l tank0 da0
gpart bootcode -b /boot/pmbr -p /boot/gptzfsboot -i 1 da0
gpart create -s GPT da1
gpart add -b 34 -s 128 -t freebsd-boot da1
gpart add -s 4g -t freebsd-swap -l swap1 da1
gpart add -s 460g -t freebsd-zfs -l tank1 da1
gpart bootcode -b /boot/pmbr -p /boot/gptzfsboot -i 1 da1
gpart create -s GPT da2
gpart add -b 34 -s 128 -t freebsd-boot da2
gpart add -s 4g -t freebsd-swap -l swap2 da2
gpart add -s 460g -t freebsd-zfs -l tank2 da2
gpart bootcode -b /boot/pmbr -p /boot/gptzfsboot -i 1 da2
gpart create -s GPT da3
gpart add -b 34 -s 128 -t freebsd-boot da3
gpart add -s 4g -t freebsd-swap -l swap3 da3
gpart add -s 460g -t freebsd-zfs -l tank3 da3
gpart bootcode -b /boot/pmbr -p /boot/gptzfsboot -i 1 da3
gmirror label -F -h -b load gmswap0 /dev/gpt/{swap0,swap1,swap2,swap3}
zpool create -O mountpoint=/mnt -O atime=off -O setuid=off -O
canmount=off tank0 raidz /dev/gpt/tank0 /dev/gpt/tank1 /dev/gpt/tank2
/dev/gpt/tank3
zfs create -o mountpoint=legacy -o setuid=on tank0/root
zpool set bootfs=tank0/root tank0
(...then zfs create for about 10 filesystems according to
http://blogs.freebsdish.org/pjd/2010/08/06/from-sysinstall-to-zfs-only-configuration/
)
zfs set mountpoint=/ system
(...then rsync data from external USB disk with working system...)
And after reboot, the same error as above.
Has somebody any suggestions?
Miroslav Lachman
PS: I can't try 8.2-RELEASE, because there is no support for PERC H200A
which was commited after RELEASE.
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?4E4BC38D.1050808>