Skip site navigation (1)Skip section navigation (2)
Date:      Thu, 2 Nov 1995 13:32:05 +1030 (CST)
From:      Michael Smith <msmith@atrad.adelaide.edu.au>
To:        phil@zipmail.co.uk
Cc:        hackers@freebsd.org, hardware@freebsd.org
Subject:   Re: [Fwd: Help, my sanity is gradually slipping awaaaayyy. was Re: Problem With Fujitsu SCSI Drive (Messages and Test Results)]
Message-ID:  <199511020302.NAA08209@genesis.atrad.adelaide.edu.au>
In-Reply-To: <3097E7F6.41C67EA6@FreeBSD.org> from "Jordan K. Hubbard" at Nov 1, 95 01:34:46 pm

next in thread | previous in thread | raw e-mail | index | archive | help
Jordan K. Hubbard stands accused of saying:
> >>I am trying to set up FBSD 2.0.5R on a system with an Adaptec AHA1542B
> >>and a Fujitsu M2694ESA 1GB SCSI-2 Drive.

Check your cables and termination!  
It's possible you have one of the over-enthusiastic 1542's; also bring all
of the jumper-selectable timings back to the slowest possible settings.

> >sd0(aha0:0:0): HARDWARE FAILURE asc: 44,a2, FAILURE
> >sd0(aha0:0:0): HARDWARE FAILURE asc: 44,a2, Retries = x
> >sd0(aha0:0:0): HARDWARE FAILURE info: 2d18 asc 15,1 Mechanical
> >positioning error sks(80,f) 
> >sd0(aha0:0:0): HARDWARE FAILURE info: 1d70 asc 15,1 Mechanical
> >positioning error sks(80,f)
> >vm_page : pager input (probably hardware) error, PID 11 failure

If you get this consistently, I would still be suspicious of the drive.
If it _is_ a translation error, there's a bug in the drive firmware if
it's accepting a request to process a block outside the size of the drive 8)

> By the way why does the ST02 floppy controller boot a 144 dos boot
> disk but not a FBSD boot disk (it reboots the machine).

The ST02 driver is a bit flaky.  I can't blame it, to be honest 8)

> Anyway back to the plot.
> 
> First I installed Novell 3.12 on the drive. It worked like a dream, I
> connected into it from another machine and was shooting around 50MB
> files with ease.
> 				NO DRIVE ERRORS

Not pushing it very hard there.

> Tried FBSD 2.0.5R a few times with various settings etc.
> 				DRIVE ERRORS

What are you doing when it fails?

> I then thought what about another UN*X, I installed SCO 3.2v4.2 8-( It
> installed seemlessly (for a change) and I could not make it error even
> by repeatedly turning it off while copying multi 50MB files between
> filesystems. Each time fsck just sorted out and I got a prompt...
> 				NO DRIVE ERRORS

Can you boot it verbosely and see what it's setting the 1542 to?  I
don't know enough about SCO's boot process 8(

> Right, what about that MCC Linux v1.0 dist on my fileserver, I
> installed that (eventually) and up it came, copied 50MB files between
> filesystems, turned it off, let it fill up /usr by growing a file by
> piping it, and guess what, 
> 				NO DRIVE ERRORS

Bingo.  Get into the source of the Linux driver and see what it's doing
as far as the bus on/off times &c.

> If anyone but anyone has seen this, or used this configuration
> successfully PLEASE let me know. I don't understand why every other OS
> other than FBSD works... I might give NetBSD a try as it is about the
> only one I haven't (or at least it seems like it).
> 
> Every other machine that I have running FBSD works perfectly so what
> is the difference ??????
> 
> As I am now babbling incoherantly I shall go........

You're on the money, it may just be that you don't have enough history 
with those damned 1542's.  If you can, check with Adaptec for details -
there was a batch (either B's or C's, I can't recall) that slewed the 
bus way too hard.  One workaround for these is, IIRC, to slow the board 
down.  Adaptec should be able to tell you whether your 1542 is one of the
culprits.

> Phil
> 
> 
> 
> -----------------------------140730798114994776041470031863--
> 
> 


-- 
]] Mike Smith, Software Engineer        msmith@atrad.adelaide.edu.au    [[
]] Genesis Software                     genesis@atrad.adelaide.edu.au   [[
]] High-speed data acquisition and                                      [[
]] realtime instrument control          (ph/fax) +61-8-267-3039         [[
]] My car has "demand start" -Terry Lambert  UNIX: live FreeBSD or die! [[



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?199511020302.NAA08209>