Date: Mon, 11 Oct 2004 23:59:30 -0700 From: Andy Sparrow <spadger@best.com> To: stable@freebsd.org Subject: PCI probe problem? Can't get CMD646 out of BIOSPIO mode? Message-ID: <20041012065930.A3B07558@CRWdog.demon.co.uk>
next in thread | raw e-mail | index | archive | help
--==_Exmh_884796434P
Content-Type: multipart/mixed ;
boundary="==_Exmh_8842519930"
This is a multipart MIME message.
--==_Exmh_8842519930
Content-Type: text/plain; charset=us-ascii
Hi,
I'm having a little trouble getting a CMD646 (built into to my laptop's
docking station) to do anything other than BIOSPIO. It comes up in
BIOSPIO, and atacontrol fails to set it higher...
Not surprisingly, it pegs the CPU mightily when I try to use anything on
those interfaces. Luckily my DVD-R has burnfree, but even so it's
running @ 25% rated speed and completely flattening the system to do
it...
There's several devices on the PCI bus behind the bridge (I presume) for
the docking station, a SymBIOS SCSI controller (which works fine), the
CMD646 and a second TI cardbus/PCMCICA controller (which seems to get
irq=255, and doesn't work; unfortunate as the built-in PC-cards are
deliberately obscured when the laptop is docked).
I tried setting hw.ata.atapi.dma=1, which doubled the reported speed for
the IDE devices on the laptop's internal IDE controller (whoo-hoo!), but
this didn't affect the stuff on the CMD646...
If I'm reading the code right, the PCI probe for the CMD646 returns
various I/O addresses and sizes.
However, all of the sizes are < ATA_BMIOSIZE, and thus channel->r_bmio
gets set to zero (in ata-dma.c). So the dmesg probe says
"bmaddr=0x0000", which I intuit is "no address for Busmastering for you".
I tried setting PCI_ENABLE_IO_MODES, which made little difference (I
diff'd the dmesg's from 'boot -v').
Can anyone make any suggestions for perhaps getting this to work a
little better, or is my only hope to eat a PCI slot for a
Promise/HighPoint Ultra IDE controller? Which is preferred or are they
pretty much as good as each other?
Thanks for any help!
Cheers,
AS
[boot -v dmesg attached:]
--==_Exmh_8842519930
Content-Type: text/plain ; name="dmesg.boot"; charset=us-ascii
Content-Description: dmesg.boot
Content-Disposition: attachment; filename="dmesg.boot"
syncing disks... 111
done
Uptime: 40m2s
The operating system has halted.
Please press any key to reboot.
Rebooting...
Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.10-STABLE #139: Sun Oct 10 22:30:16 PDT 2004
root@tureg.geek4food.org:/usr/src/sys/compile/tureg
Calibrating clock(s) ... TSC clock: 796538270 Hz, i8254 clock: 1193183 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
CPU: Intel Pentium III (796.54-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x686 Stepping = 6
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 536805376 (524224K bytes)
Physical memory chunk(s):
0x000001000 - 0x00009efff, 647168 bytes (158 pages)
0x00048c000 - 0x01ffe7fff, 532004864 bytes (129884 pages)
avail memory = 517795840 (505660K bytes)
bios32: Found BIOS32 Service Directory header at 0xc00f67c0
bios32: Entry = 0xfd82c (c00fd82c) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0x2b0
pnpbios: Found PnP BIOS data at 0xc00f67f0
pnpbios: Entry = f0000:9c4f Rev = 1.0
pnpbios: Event flag at 4b4
Other BIOS signatures found:
ACPI: 000f6780
Preloaded elf kernel "kernel" at 0xc0465000.
Preloaded elf module "snd_maestro3.ko" at 0xc04650a8.
Preloaded elf module "snd_pcm.ko" at 0xc046514c.
VESA: information block
56 45 53 41 00 02 00 01 00 01 00 00 00 00 22 00
00 01 7f 00 00 01 0b 01 00 01 21 01 00 01 2a 01
00 01 00 01 01 01 10 01 11 01 12 01 03 01 13 01
14 01 15 01 05 01 16 01 17 01 18 01 07 01 19 01
VESA: 0 mode(s) found
module_register_init: MOD_LOAD (vesa, c0300898, 0) error 6
Pentium Pro MTRR support enabled
Creating DISK md0
md0: Malloc disk
pci_open(1): mode 1 addr port (0x0cf8) is 0x80003904
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=71908086)
Using $PIR table, 9 entries at 0xc00fdf30
apm0: <APM BIOS> on motherboard
apm0: found APM BIOS v1.2, connected at v1.2
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> on motherboard
found-> vendor=0x8086, dev=0x7190, revid=0x03
class=06-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[10]: type 1, range 32, base f8000000, size 26
found-> vendor=0x8086, dev=0x7191, revid=0x03
class=06-04-00, hdrtype=0x01, mfdev=0
subordinatebus=1 secondarybus=1
found-> vendor=0x8086, dev=0x7110, revid=0x02
class=06-80-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x8086, dev=0x7111, revid=0x01
class=01-01-80, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[20]: type 1, range 32, base 00001460, size 4
found-> vendor=0x8086, dev=0x7112, revid=0x01
class=0c-03-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=d, irq=10
map[20]: type 1, range 32, base 00001440, size 5
found-> vendor=0x8086, dev=0x7113, revid=0x03
class=06-80-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[90]: type 1, range 32, base 00002180, size 4
found-> vendor=0x104c, dev=0xac51, revid=0x00
class=06-07-00, hdrtype=0x02, mfdev=1
subordinatebus=0 secondarybus=0
intpin=a, irq=255
found-> vendor=0x104c, dev=0xac51, revid=0x00
class=06-07-00, hdrtype=0x02, mfdev=1
subordinatebus=0 secondarybus=0
intpin=b, irq=255
found-> vendor=0x8086, dev=0x1229, revid=0x0c
class=02-00-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
intpin=a, irq=10
map[10]: type 1, range 32, base f4002000, size 12
map[14]: type 1, range 32, base 00001400, size 6
map[18]: type 1, range 32, base f4020000, size 17
found-> vendor=0x11c1, dev=0x045c, revid=0x01
class=07-00-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
intpin=a, irq=10
map[10]: type 1, range 32, base 00001470, size 3
map[14]: type 1, range 32, base f4003000, size 12
found-> vendor=0x125d, dev=0x1998, revid=0x00
class=04-01-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=5
map[10]: type 1, range 32, base 00001000, size 8
map[14]: type 1, range 32, base f4000000, size 13
found-> vendor=0x8086, dev=0x124b, revid=0x01
class=06-04-80, hdrtype=0x01, mfdev=0
subordinatebus=2 secondarybus=2
pci0: <PCI bus> on pcib0
agp0: <Intel 82443BX (440 BX) host to PCI bridge> mem 0xf8000000-0xfbffffff at device 0.0 on pci0
agp0: allocating GATT for aperture of size 64M
pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on pci0
found-> vendor=0x1002, dev=0x4c4d, revid=0x64
class=03-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=10
map[10]: type 1, range 32, base f5000000, size 24
map[14]: type 1, range 32, base 00009000, size 8
map[18]: type 1, range 32, base f4100000, size 12
pci1: <PCI bus> on pcib1
pci1: <ATI Mobility-1 graphics accelerator> (vendor=0x1002, dev=0x4c4d) at 0.0 irq 10
isab0: <Intel 82371AB PCI to ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0x1460-0x146f at device 7.1 on pci0
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0x1460
ata0: mask=03 ostat0=50 ostat2=00
ata0-master: ATAPI 00 00
ata0-slave: ATAPI 00 00
ata0: mask=03 stat0=50 stat1=00
ata0-master: ATA 01 a5
ata0: devices=01
ata0: at 0x1f0 irq 14 on atapci0
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0x1468
ata1: mask=03 ostat0=50 ostat2=01
ata1-master: ATAPI 14 eb
ata1-slave: ATAPI 00 00
ata1: mask=03 stat0=00 stat1=01
ata1-slave: ATA 04 00
ata1: devices=04
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0x1440-0x145f irq 10 at device 7.2 on pci0
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
intpm0: <Intel 82371AB Power management controller> port 0x2180-0x218f irq 9 at device 7.3 on pci0
intpm0: I/O mapped 2180
intpm0: intr IRQ 9 enabled revision 0
smbus0: <System Management Bus> on intsmb0
smb0: <SMBus general purpose I/O> on smbus0
intpm0: PM I/O mapped 8000
pci_cfgintr_linked: linked (60) to hard-routed irq 10
pci_cfgintr: 0:10 INTA routed to irq 10
pcic0: <TI PCI-1420 PCI-CardBus Bridge> irq 10 at device 10.0 on pci0
pcic0: PCI Memory allocated: 0x88000000
pcic0: TI12XX PCI Config Reg: [ring enable][speaker enable][pwr save][FUNC pci int + CSC serial isa irq]
using shared irq10.
pcic0: PCI Configuration space:
0x00: 0xac51104c 0x02100007 0x06070000 0x00820000
0x10: 0x88000000 0x020000a0 0x20000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x00000000 0x00000000 0x00000000 0x0760010a
0x40: 0x0010103c 0x00000001 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00449061 0x00000000 0x00000000 0x012c1272
0x90: 0x616682c0 0x00000000 0x00000000 0x00000000
0xa0: 0xfe110001 0x00c00000 0x00000011 0x0000001e
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
pccard0: <PC Card 16-bit bus (classic)> on pcic0
pci_cfgintr_linked: linked (61) to hard-routed irq 10
pci_cfgintr: 0:10 INTB routed to irq 10
pcic1: <TI PCI-1420 PCI-CardBus Bridge> irq 10 at device 10.1 on pci0
pcic1: PCI Memory allocated: 0x88001000
pcic1: TI12XX PCI Config Reg: [ring enable][speaker enable][pwr save][FUNC pci int + CSC serial isa irq]
pcic1: PCI Configuration space:
0x00: 0xac51104c 0x02100007 0x06070000 0x00820000
0x10: 0x88001000 0x020000a0 0x20000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x00000000 0x00000000 0x00000000 0x0760020a
0x40: 0x0010103c 0x00000001 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00449061 0x00000000 0x00000000 0x012c1272
0x90: 0x616682c0 0x00000000 0x00000000 0x00000000
0xa0: 0xfe110001 0x00c00000 0x00000011 0x0000001e
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
pccard1: <PC Card 16-bit bus (classic)> on pcic1
fxp0: <Intel 82550 Pro/100 Ethernet> port 0x1400-0x143f mem 0xf4020000-0xf403ffff,0xf4002000-0xf4002fff irq 10 at device 11.0 on pci0
fxp0: using memory space register mapping
fxp0: Ethernet address 00:03:47:8e:4f:86
fxp0: PCI IDs: 8086 1229 8086 2205 000c
fxp0: Dynamic Standby mode is disabled
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bpf: fxp0 attached
pci0: <unknown card> (vendor=0x11c1, dev=0x045c) at 11.1 irq 10
pcm0: <ESS Technology Maestro3> port 0x1000-0x10ff mem 0xf4000000-0xf4001fff irq 5 at device 13.0 on pci0
pcm0: <SigmaTel STAC9721/23 AC97 Codec (id = 0x83847609)>
pcm0: Codec features 18 bit DAC, 18 bit ADC, 5 bit master volume, SigmaTel 3D Enhancement
pcm0: Primary codec extended features AMAP
pcm0: sndbuf_setmap 1000, 1000; 0xda7b7000 -> 1000
pcm0: sndbuf_setmap 2000, 1000; 0xda7b8000 -> 2000
pcm0: sndbuf_setmap 3000, 1000; 0xda7b9000 -> 3000
pcm0: sndbuf_setmap 4000, 1000; 0xda7ba000 -> 4000
pcm0: sndbuf_setmap 5000, 1000; 0xda7bb000 -> 5000
pcib2: <Intel 82380FB mobile PCI to PCI bridge> at device 17.0 on pci0
found-> vendor=0x104c, dev=0xac17, revid=0x02
class=06-07-00, hdrtype=0x02, mfdev=1
subordinatebus=0 secondarybus=0
intpin=a, irq=255
found-> vendor=0x104c, dev=0xac17, revid=0x02
class=06-07-00, hdrtype=0x02, mfdev=1
subordinatebus=0 secondarybus=0
intpin=b, irq=255
found-> vendor=0x1095, dev=0x0646, revid=0x05
class=01-01-8f, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=10
map[10]: type 1, range 32, base 0000a420, size 3
map[14]: type 1, range 32, base 0000a414, size 2
map[18]: type 3, range 32, base 0000a418, size 3
map[1c]: type 1, range 32, base 0000a410, size 2
map[20]: type 1, range 32, base 0000a400, size 4
found-> vendor=0x1000, dev=0x0001, revid=0x23
class=01-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=10
map[10]: type 1, range 32, base 0000a000, size 8
map[14]: type 1, range 32, base f6000000, size 8
pci2: <PCI bus> on pcib2
pci_cfgintr: can't route an interrupt to 2:8 INTA
pcic2: <TI PCI-1220 PCI-CardBus Bridge> at device 8.0 on pci2
pcic2: PCI Memory allocated: 0x88002000
pci_cfgintr: can't route an interrupt to 2:8 INTA
pcic2: No PCI interrupt routed, trying ISA.
pcic2: Polling mode
pcic2: TI12XX PCI Config Reg: [speaker enable][pwr save][FUNC pci int + CSC serial isa irq]
pcic2: PCI Configuration space:
0x00: 0xac17104c 0x02100003 0x06070002 0x00824000
0x10: 0x88002000 0x020000a0 0x20000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x00000000 0x00000000 0x00000000 0x07e001ff
0x40: 0x0005103c 0x00000001 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x08449061 0x00000000 0x00000000 0x01021c00
0x90: 0x616602c0 0x00000000 0x00000000 0x00000000
0xa0: 0x7e210001 0x00800000 0x00000006 0x00000009
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
pccard2: <PC Card 16-bit bus (classic)> on pcic2
pci_cfgintr: can't route an interrupt to 2:8 INTB
pcic3: <TI PCI-1220 PCI-CardBus Bridge> at device 8.1 on pci2
pcic3: PCI Memory allocated: 0x88003000
pci_cfgintr: can't route an interrupt to 2:8 INTB
pcic3: No PCI interrupt routed, trying ISA.
pcic3: Polling mode
pcic3: TI12XX PCI Config Reg: [speaker enable][pwr save][FUNC pci int + CSC serial isa irq]
pcic3: PCI Configuration space:
0x00: 0xac17104c 0x02100003 0x06070002 0x00824000
0x10: 0x88003000 0x020000a0 0x20000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x00000000 0x00000000 0x00000000 0x07e002ff
0x40: 0x0005103c 0x00000001 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x08449061 0x00000000 0x00000000 0x01021c00
0x90: 0x616602c0 0x00000000 0x00000000 0x00000000
0xa0: 0x7e210001 0x00800000 0x00000006 0x00000009
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
pccard3: <PC Card 16-bit bus (classic)> on pcic3
atapci1: <CMD 646 ATA controller> port 0xa400-0xa40f,0xa410-0xa413,0xa418-0xa41f,0xa414-0xa417,0xa420-0xa427 irq 10 at device 12.0 on pci2
atapci1: Busmastering DMA not supported
atapci1: CMD 646 enable interrupts, set DMA read mode
ata-: ata2 exists, using next available unit number
ata2: iobase=0xa420 altiobase=0xa416 bmaddr=0x0000
ata2: mask=03 ostat0=00 ostat2=00
ata2-master: ATAPI 14 eb
ata2-slave: ATAPI 00 00
ata2: mask=03 stat0=00 stat1=00
ata2: devices=04
ata2: at 0xa420 on atapci1
ata3: iobase=0xa418 altiobase=0xa412 bmaddr=0x0000
ata3: mask=03 ostat0=50 ostat2=00
ata3-master: ATAPI 00 00
ata3-slave: ATAPI 00 00
ata3: mask=03 stat0=50 stat1=00
ata3-master: ATA 01 a5
ata3: devices=01
ata3: at 0xa418 on atapci1
sym0: <810a> port 0xa000-0xa0ff mem 0xf6000000-0xf60000ff irq 10 at device 13.0 on pci2
sym0: No NVRAM, ID 7, Fast-10, SE, parity checking
sym0: open drain IRQ line driver
sym0: using LOAD/STORE-based firmware.
pcic-: pcic0 exists, using next available unit number
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROMs> at iomem 0xc0000-0xcc7ff,0xcc800-0xcdfff on isa0
pmtimer0 on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
aic0 failed to probe at port 0x140-0x15f on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0045
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
psm0: current command byte:0045
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0-00, 2 buttons
psm0: config:00006000, flags:00000000, packet size:3
psm0: syncmask:c0, syncbits:00
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 06 40 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
pcic4 failed to probe at port 0x3e0 iomem 0xd0000 irq 10 on isa0
sio0: irq maps: 0x61 0x71 0x61 0x61
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
ppc0: parallel port found at 0x378
ppc0: using extended I/O port range
ppc0: ECP SPP SPP
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
plip0: <PLIP network interface> on ppbus0
bpf: lp0 attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
isa_probe_children: probing PnP devices
BIOS Geometries:
0:03feef3f 0..1022=1023 cylinders, 0..239=240 heads, 1..63=63 sectors
0 accounted for
Device configuration finished.
IP packet filtering initialized, divert enabled, rule-based forwarding enabled, default to deny, logging disabled
bpf: lo0 attached
DUMMYNET initialized (011031)
bpf: faith0 attached
IPsec: Initialized Security Association Processing.
ad0: success setting UDMA2 on Intel chip
Creating DISK ad0
ar: FreeBSD check1 failed
ad0: <IC25N040ATCS04-0/CA4OA71A> ATA-5 disk at ata0-master
ad0: 38154MB (78140160 sectors), 77520 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, UDMA33
ad0: piomode=4 dmamode=2 udmamode=5 cblid=1
Creating DISK ad1
ar: FreeBSD check1 failed
ad1: <IBM-DJSA-220/JS4OAC3A> ATA-5 disk at ata3-master
ad1: 19077MB (39070080 sectors), 38760 C, 16 H, 63 S, 512 B
ad1: 16 secs/int, 1 depth queue, BIOSPIO
ad1: piomode=4 dmamode=2 udmamode=4 cblid=1
ata1-master: piomode=4 dmamode=2 udmamode=2 dmaflag=1
ata1-master: success setting UDMA2 on Intel chip
acd0: <DW-28E/1.0A> CD-RW drive at ata1 as master
acd0: read 4134KB/s (34515KB/s) write 1377KB/s (1377KB/s), 1698KB buffer, UDMA33
acd0: Reads: CD-R, CD-RW, CD-DA stream, DVD-ROM, DVD-R, packet
acd0: Writes: CD-R, CD-RW, test write
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: CD-R 120mm data disc
ata2-master: piomode=4 dmamode=2 udmamode=2 dmaflag=1
acd1: <PLEXTOR DVDR PX-712A/1.04> DVD-R drive at ata2 as master
acd1: read 6890KB/s (36026KB/s) write 8268KB/s (8268KB/s), 8192KB buffer, BIOSPIO
acd1: Reads: CD-R, CD-RW, CD-DA stream, DVD-ROM, DVD-R, packet
acd1: Writes: CD-R, CD-RW, DVD-R, test write, burnproof
acd1: Audio: play, 256 volume levels
acd1: Mechanism: ejectable tray, unlocked
acd1: Medium: CD-R blank
Waiting 2 seconds for SCSI devices to settle
(noperiph:sym0:0:-1:-1): SCSI BUS reset delivered.
(probe4:ata2:0:0:0): INQUIRY. CDB: 12 1 80 0 ff 0
(probe4:ata2:0:0:0): ILLEGAL REQUEST asc:24,0
(probe4:ata2:0:0:0): Invalid field in CDB
(probe4:ata2:0:0:0): INQUIRY. CDB: 12 1 80 0 ff 0
(probe4:ata2:0:0:0): ILLEGAL REQUEST asc:24,0
(probe4:ata2:0:0:0): Invalid field in CDB
Creating DISK cd0
Creating DISK cd1
pass0 at ata1 bus 0 target 0 lun 0
pass0: <TEAC DW-28E 1.0A> Removable CD-ROM SCSI-0 device
pass0: Serial Number [
pass0: 33.000MB/s transfers
pass1 at ata2 bus 0 target 0 lun 0
pass1: <PLEXTOR DVDR PX-712A 1.04> Removable CD-ROM SCSI-0 device
pass1: 3.300MB/s transfers
cd0 at ata1 bus 0 target 0 lun 0
cd0: <TEAC DW-28E 1.0A> Removable CD-ROM SCSI-0 device
cd0: Serial Number [
cd0: 33.000MB/s transfers
cd0: cd present [189185 x 2048 byte records]
Mounting root from ufs:/dev/ad0s2a
cd1 at ata2 bus 0 target 0 lun 0
cd1: <PLEXTOR DVDR PX-712A 1.04> Removable CD-ROM SCSI-0 device
cd1: 3.300MB/s transfers
cd1: cd present [1 x 2048 byte records]
ad0s1: type 0xa0, start 63, end = 1088639, size 1088577 : OK
ad0s2: type 0xa5, start 1088640, end = 78140159, size 77051520 : OK
start_init: trying /sbin/init
--==_Exmh_8842519930--
--==_Exmh_884796434P
Content-Type: application/pgp-signature
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.2.6 (FreeBSD)
Comment: Exmh version 2.6.3 04/04/2003
iD8DBQFBa4DSPHh895bDXeQRAqj9AJ4tjGGeSRSD5Vb8XnGN7gBMJHbqSACfZ0HN
cjTmRPMXVa5phE2XgDYlym8=
=3lCN
-----END PGP SIGNATURE-----
--==_Exmh_884796434P--
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20041012065930.A3B07558>