Date: Tue, 13 Jul 1999 06:32:49 -0700 (PDT) From: ilg@livius.net To: freebsd-gnats-submit@freebsd.org Subject: kern/12626: Adaptec 3950 in 3.2 fails to probe disks Message-ID: <19990713133249.3F02D152F3@hub.freebsd.org>
next in thread | raw e-mail | index | archive | help
>Number: 12626 >Category: kern >Synopsis: Adaptec 3950 in 3.2 fails to probe disks >Confidential: no >Severity: serious >Priority: high >Responsible: freebsd-bugs >State: open >Quarter: >Keywords: >Date-Required: >Class: sw-bug >Submitter-Id: current-users >Arrival-Date: Tue Jul 13 06:40:03 PDT 1999 >Closed-Date: >Last-Modified: >Originator: Liviu Ionescu >Release: 3.2-RELEASE >Organization: KPNQwest >Environment: FreeBSD buh104.ro.eu.net 3.2-RELEASE FreeBSD 3.2-RELEASE #0: Tue May 18 04:05:08 GMT 1999 jkh@cathair:/usr/src/sys/compile/GENERIC i386 >Description: while booting the GENERIC 3.2 kernel, although the Adaptec 3950 card is identified as a valid PCI device, attached disks are not recognized. after replacing the card with a 2940, exactly the same configuration booted without problems. as far as I remember (I don't have a 3.1 disk at hand to give it a try), exactly the same configuration worked in 3.1-RELEASE. the dmesg output for the 3950 boot follows: Copyright (c) 1992-1999 FreeBSD Inc. Copyright (c) 1982, 1986, 1989, 1991, 1993 The Regents of the University of California. All rights reserved. FreeBSD 3.2-RELEASE #0: Tue May 18 04:05:08 GMT 1999 jkh@cathair:/usr/src/sys/compile/GENERIC Timecounter "i8254" frequency 1193182 Hz CPU: Pentium II/Xeon/Celeron (348.49-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x652 Stepping=2 Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,<b24>> real memory = 134217728 (131072K bytes) avail memory = 127070208 (124092K bytes) Preloaded elf kernel "kernel" at 0xc0358000. Probing for devices on PCI bus 0: chip0: <Intel 82443BX host to PCI bridge> rev 0x03 on pci0.0.0 chip1: <Intel 82443BX host to AGP bridge> rev 0x03 on pci0.1.0 fxp0: <Intel EtherExpress Pro 10/100B Ethernet> rev 0x05 int a irq 9 on pci0.6.0 fxp0: Ethernet address 00:a0:c9:fc:c6:8a chip2: <Intel 82371AB PCI to ISA bridge> rev 0x02 on pci0.7.0 ide_pci0: <Intel PIIX4 Bus-master IDE controller> rev 0x01 on pci0.7.1 chip3: <Intel 82371AB Power management controller> rev 0x02 on pci0.7.3 fxp1: <Intel EtherExpress Pro 10/100B Ethernet> rev 0x08 int a irq 10 on pci0.18.0 fxp1: Ethernet address 00:90:27:84:a0:01 ahc0: <Adaptec 3950B Ultra2 SCSI adapter> rev 0x00 int a irq 11 on pci0.20.0 ahc0: aic7896/97 Wide Channel A, SCSI Id=7, 16/255 SCBs ahc1: <Adaptec 3950B Ultra2 SCSI adapter> rev 0x00 int a irq 11 on pci0.20.1 ahc1: aic7896/97 Wide Channel B, SCSI Id=7, 16/255 SCBs Probing for devices on PCI bus 1: vga0: <ATI model 4742 graphics accelerator> rev 0x5c int a irq 11 on pci1.0.0 Probing for PnP devices: CSN 1 Vendor ID: CSC0225 [0x2502630e] Serial 0xffffffff Comp ID: @@@0000 [0x00000000] Probing for devices on the ISA bus: sc0 on isa sc0: VGA color <16 virtual consoles, flags=0x0> ed0 not found at 0x280 fe0 not found at 0x300 atkbdc0 at 0x60-0x6f on motherboard atkbd0 irq 1 on isa psm0 not found sio0 at 0x3f8-0x3ff irq 4 flags 0x10 on isa sio0: type 16550A sio1 at 0x2f8-0x2ff irq 3 on isa sio1: type 16550A fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa wdc0 at 0x1f0-0x1f7 irq 14 on isa wdc0: unit 0 (wd0): <WDC AC26400R> wd0: 6149MB (12594960 sectors), 13328 cyls, 15 heads, 63 S/T, 512 B/S wdc1 at 0x170-0x177 irq 15 on isa wdc1: unit 0 (wd2): <M-SYSTEMS ATA Ver 3.2S> wd2: 31MB (64000 sectors), 500 cyls, 8 heads, 16 S/T, 512 B/S wdc1: unit 1 (wd3): <M-SYSTEMS ATA Ver 3.2S> wd3: 7MB (16000 sectors), 250 cyls, 4 heads, 16 S/T, 512 B/S wt0 not found at 0x300 mcd0 not found at 0x300 matcdc0 not found at 0x230 scd0 not found at 0x230 ppc0 at 0x378 irq 7 flags 0x40 on isa ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/8 bytes threshold lpt0: <generic printer> on ppbus 0 lpt0: Interrupt-driven port ppi0: <generic parallel i/o> on ppbus 0 plip0: <PLIP network interface> on ppbus 0 lpt0: <generic printer> on ppbus 0 lpt0: Interrupt-driven port ie0: unknown board_id: f000 ie0 not found at 0x300 ep0 not found at 0x300 ex0 not found le0 not found at 0x300 lnc0 not found at 0x280 ze0 not found at 0x300 zp0 not found at 0x300 cs0 not found at 0x300 adv0 not found at 0x330 bt_isa_probe: Probe failled for card at 0x330 bt_isa_probe: Probe failled for card at 0x334 bt_isa_probe: Probe failled for card at 0x230 bt_isa_probe: Probe failled for card at 0x234 bt_isa_probe: Probe failled for card at 0x130 bt_isa_probe: Probe failled for card at 0x134 bt0 not found at 0x134 aha0 not found at 0x134 vga0 at 0x3b0-0x3df maddr 0xa0000 msize 131072 on isa npx0 on motherboard npx0: INT 16 interface Waiting 15 seconds for SCSI devices to settle ahc0: Someone reset channel A (probe1:ahc0:0:1:0): SCB 0xe - timed out while idle, LASTPHASE == 0x1, SEQADDR == 0x45 (probe1:ahc0:0:1:0): Queuing a BDR SCB (probe1:ahc0:0:1:0): SCB 0xe - timed out while idle, LASTPHASE == 0x1, SEQADDR == 0x7 (probe1:ahc0:0:1:0): no longer in timeout, status = 34b ahc0: Issued Channel A Bus Reset. 15 SCBs aborted ahc0: Someone reset channel A (probe1:ahc0:0:1:0): SCB 0x1 - timed out while idle, LASTPHASE == 0x1, SEQADDR == 0x43 (probe1:ahc0:0:1:0): Queuing a BDR SCB (probe1:ahc0:0:1:0): SCB 0x1 - timed out while idle, LASTPHASE == 0x1, SEQADDR == 0x6 (probe1:ahc0:0:1:0): no longer in timeout, status = 34b ahc0: Issued Channel A Bus Reset. 2 SCBs aborted ahc0: Someone reset channel A <<<manually disconect disk from the SCSI bus using the HotSwap key>>> changing root device to wd0s1a the dmesg output when using the 2940 card: Copyright (c) 1992-1999 FreeBSD Inc. Copyright (c) 1982, 1986, 1989, 1991, 1993 The Regents of the University of California. All rights reserved. FreeBSD 3.2-RELEASE #0: Tue May 18 04:05:08 GMT 1999 jkh@cathair:/usr/src/sys/compile/GENERIC Timecounter "i8254" frequency 1193182 Hz CPU: Pentium II/Xeon/Celeron (348.49-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x652 Stepping=2 Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,<b24>> real memory = 134217728 (131072K bytes) avail memory = 127070208 (124092K bytes) Preloaded elf kernel "kernel" at 0xc0358000. Probing for devices on PCI bus 0: chip0: <Intel 82443BX host to PCI bridge> rev 0x03 on pci0.0.0 chip1: <Intel 82443BX host to AGP bridge> rev 0x03 on pci0.1.0 fxp0: <Intel EtherExpress Pro 10/100B Ethernet> rev 0x05 int a irq 9 on pci0.6.0 fxp0: Ethernet address 00:a0:c9:fc:c6:8a chip2: <Intel 82371AB PCI to ISA bridge> rev 0x02 on pci0.7.0 ide_pci0: <Intel PIIX4 Bus-master IDE controller> rev 0x01 on pci0.7.1 chip3: <Intel 82371AB Power management controller> rev 0x02 on pci0.7.3 fxp1: <Intel EtherExpress Pro 10/100B Ethernet> rev 0x08 int a irq 10 on pci0.18.0 fxp1: Ethernet address 00:90:27:84:a0:01 ahc0: <Adaptec 2940 Ultra2 SCSI adapter> rev 0x00 int a irq 11 on pci0.20.0 ahc0: aic7890/91 Wide Channel A, SCSI Id=7, 16/255 SCBs Probing for devices on PCI bus 1: vga0: <ATI model 4742 graphics accelerator> rev 0x5c int a irq 11 on pci1.0.0 Probing for PnP devices: CSN 1 Vendor ID: CSC0225 [0x2502630e] Serial 0xffffffff Comp ID: @@@0000 [0x00000000] Probing for devices on the ISA bus: sc0 on isa sc0: VGA color <16 virtual consoles, flags=0x0> ed0 not found at 0x280 fe0 not found at 0x300 atkbdc0 at 0x60-0x6f on motherboard atkbd0 irq 1 on isa psm0 not found sio0 at 0x3f8-0x3ff irq 4 flags 0x10 on isa sio0: type 16550A sio1 at 0x2f8-0x2ff irq 3 on isa sio1: type 16550A fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa wdc0 at 0x1f0-0x1f7 irq 14 on isa wdc0: unit 0 (wd0): <WDC AC26400R> wd0: 6149MB (12594960 sectors), 13328 cyls, 15 heads, 63 S/T, 512 B/S wdc1 at 0x170-0x177 irq 15 on isa wdc1: unit 0 (wd2): <M-SYSTEMS ATA Ver 3.2S> wd2: 31MB (64000 sectors), 500 cyls, 8 heads, 16 S/T, 512 B/S wdc1: unit 1 (wd3): <M-SYSTEMS ATA Ver 3.2S> wd3: 7MB (16000 sectors), 250 cyls, 4 heads, 16 S/T, 512 B/S wt0 not found at 0x300 mcd0 not found at 0x300 matcdc0 not found at 0x230 scd0 not found at 0x230 ppc0 at 0x378 irq 7 flags 0x40 on isa ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/8 bytes threshold lpt0: <generic printer> on ppbus 0 lpt0: Interrupt-driven port ppi0: <generic parallel i/o> on ppbus 0 plip0: <PLIP network interface> on ppbus 0 lpt0: <generic printer> on ppbus 0 lpt0: Interrupt-driven port ie0: unknown board_id: f000 ie0 not found at 0x300 ep0 not found at 0x300 ex0 not found le0 not found at 0x300 lnc0 not found at 0x280 ze0 not found at 0x300 zp0 not found at 0x300 cs0 not found at 0x300 adv0 not found at 0x330 bt_isa_probe: Probe failled for card at 0x330 bt_isa_probe: Probe failled for card at 0x334 bt_isa_probe: Probe failled for card at 0x230 bt_isa_probe: Probe failled for card at 0x234 bt_isa_probe: Probe failled for card at 0x130 bt_isa_probe: Probe failled for card at 0x134 bt0 not found at 0x134 aha0 not found at 0x134 vga0 at 0x3b0-0x3df maddr 0xa0000 msize 131072 on isa npx0 on motherboard npx0: INT 16 interface Waiting 15 seconds for SCSI devices to settle changing root device to wd0s1a da0 at ahc0 bus 0 target 0 lun 0 da0: <SEAGATE ST39102LW 0005> Fixed Direct Access SCSI-2 device da0: 80.000MB/s transfers (40.000MHz, offset 15, 16bit), Tagged Queueing Enabled da0: 8683MB (17783240 512 byte sectors: 255H 63S/T 1106C) >How-To-Repeat: simply reboot >Fix: immediatelly after disconnecting the SCSI disk from the LVD bus (we are using a Livingston HotSwap frame) the kernel resumes the boot procedure. >Release-Note: >Audit-Trail: >Unformatted: To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-bugs" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?19990713133249.3F02D152F3>