Date: Thu, 11 Oct 2001 11:22:26 -0400 From: "Flint" <flint@virtualflu.com> To: <mobile@freebsd.org> Subject: Current, Satellite 1555-CDS and CPU/System Fan (ACPI) Message-ID: <003501c15268$88ab7920$0300000a@voltaire>
next in thread | raw e-mail | index | archive | help
I installed -current (by installing -release, and then cvsup'ing,
buildworld'ing, etc) on my Satellite 1555CDS the other day to try and get a
netcard working, and generally just for the hell of it. Everything boots
fine with ppcbb and cardbus added to the kernel [both with and without it].
I've attached the dmesg output below.
My problem is, the thing seems to overheat, and the internal system fan
won't kick in. I can do a 'sysctl -w hw.acpi.thermal.tz0.active=1', and
that causes the fan to kick in for about 2 seconds, then it will stop, and
restart, along with this message on the console:
acpi_tz0: switched from _AC-1 to _AC1
and will continue to kick the fan on/off in at about 3-4 second intervals.
It's getting quite hot in there, the fan runs under 2k a lot. Is there a
way to just leave the thing running all of the time? (or just to fix the
"tripping" process..)
Thanks,
- Flint
--
Copyright (c) 1992-2001 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.0-CURRENT #0: Wed Oct 10 19:24:09 EDT 2001
root@satellite:/usr/src/sys/i386/compile/satellite
Timecounter "i8254" frequency 1193182 Hz
CPU: AMD-K6(tm) 3D processor (380.46-MHz 586-class CPU)
Origin = "AuthenticAMD" Id = 0x58c Stepping = 12
Features=0x8021bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,PGE,MMX>
AMD Features=0x80000800<SYSCALL,3DNow!>
real memory = 167575552 (163648K bytes)
avail memory = 157990912 (154288K bytes)
Preloaded elf kernel "/boot/kernel/kernel" at 0xc040a000.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc040a0a8.
K6-family MTRR support enabled (2 registers)
Using $PIR table, 5 entries at 0xc00fec60
apm0: <APM BIOS> on motherboard
apm0: found APM BIOS v1.2, connected at v1.2
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <TOSHIB 750 > on motherboard
acpi0: power button is handled as a fixed feature programming model.
Timecounter "ACPI" frequency 3579545 Hz
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x18a8-0x18ab on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_tz0: <thermal zone> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_acad0: <AC adapter> on acpi0
acpi_cmbat0: <Control method Battery> on acpi0
acpi_pcib0: <Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <PCI bus> on acpi_pcib0
pci0: <display, VGA> at device 8.0 (no driver attached)
pci0: <serial bus, USB> at device 11.0 (no driver attached)
pcm0: <ESS Technology Maestro-2E> port 0xff00-0xffff irq 11 at device 12.0
on pci0
atapci0: <Generic PCI ATA controller> port 0x1800-0x180f at device 16.0 on
pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pccbb0: <ToPIC97 PCI-CardBus Bridge> at device 19.0 on pci0
pccbb0: PCI Memory allocated: 10000000
acpi_pcib0: matched entry for 0.19.INTA (source \\_SB_.PCI0.EIO_.LNKA)
acpi_pcib0: device is routed to IRQ 11
cardbus0: <Cardbus bus (newcard)> on pccbb0
pccard0: <16-bit PCCard bus> on pccbb0
pccbb1: <ToPIC97 PCI-CardBus Bridge> at device 19.1 on pci0
pccbb1: PCI Memory allocated: 10001000
acpi_pcib0: matched entry for 0.19.INTB (source \\_SB_.PCI0.EIO_.LNKB)
acpi_pcib0: device is routed to IRQ 11
cardbus1: <Cardbus bus (newcard)> on pccbb1
pccard1: <16-bit PCCard bus> on pccbb1
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model GlidePoint, device ID 0
fdc0: <NEC 72065B or clone> port 0x3f7,0x3f2-0x3f5 irq 6 on acpi0
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
isa0: <ISA bus> on motherboard
orm0: <Option ROM> at iomem 0xc0000-0xcbfff on isa0
fdc1: cannot reserve I/O port range (6 ports)
pmtimer0 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio2: configured irq 3 not in bitmap of probed irqs 0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
acpi_cpu0: set speed to 100.0%
acpi_cpu: CPU throttling enabled, 16 steps from 100% to 6.2%
ad0: 4126MB <TOSHIBA MK4313MAT> [8944/15/63] at ata0-master BIOSDMA
acd0: CDROM <TOSHIBA CD-ROM XM-7002B> at ata1-master PIO4
Mounting root from ufs:/dev/ad0s1a
pccbb0: card inserted: event=0x00000006, state=30000820
pccbb0: pccbb_power: CARD_VCC_0V and CARD_VPP_0V [44]
pccbb0: pccbb_power: CARD_VCC_3V and CARD_VPP_VCC [11]
found-> vendor=0x13d1, dev=0xab02, revid=0x11
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0000, statreg=0x0290, cachelnsz=8 (dwords)
lattimer=0xa8 (5040 ns), mingnt=0xff (63750 ns), maxlat=0xff (63750 ns)
intpin=a, irq=128
cardbus0: Expecting link target, got 0x59
cardbus0: Resource not specified in CIS: id=10, size=100
cardbus0: Resource not specified in CIS: id=14, size=400
cardbus0: Non-prefetchable memory at 44000000-440003ff
cardbus0: Non-prefetchable memory rid=14 at 44000000-440003ff (400)
cardbus0: IO port at 1000-10ff
cardbus0: IO port rid=10 at 1000-10ff
dc0: <Abocom FE2500 10/100BaseTX> port 0x1000-0x10ff mem
0x44000000-0x440003ff irq 11 at device 0.0 on cardbus0
dc0: Ethernet address: 00:e0:98:86:88:29
miibus0: <MII bus> on dc0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
cardbus1: detach_card: no card to detach!
pccbb1: pccbb_power: CARD_VCC_0V and CARD_VPP_0V [44]
dc0: failed to force tx and rx to idle state
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-mobile" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?003501c15268$88ab7920$0300000a>