Date: Tue, 1 Feb 2000 00:48:48 +0100 From: Andreas Braukmann <braukmann@tse-online.de> To: current@freebsd.org Subject: sym0 v1.4 vs. SMP Message-ID: <20000201004848.B27262@cage.tse-online.de>
next in thread | raw e-mail | index | archive | help
--azLHFNyN32YCQGCU
Content-Type: text/plain; charset=us-ascii
Hi there,
... I have an SMP-box (dual PPro, Natoma, mptable output attached) running
-current (with src/sys/dev/sym/sym_hipd.c,v 1.4 2000/01/08 19:58:17)
from around 2000/01/22.
The machine was running a 'ca. mid 1999' -current/SMP happily
for the last few months. I did the upgrade (fresh install) to give
the mylex drivers a shot. And because of the non-booting mlx-driver
I left my symbios logic dual channel (symbios logic '876 chip)
hostadaptor in the machine and included the sym-device in the
kernel configuration. (I run the sym-driver on all our other
symbios logic hostadaptors)
Today I switched from GENERIC (UP) to a more specific configuration
and to SMP (again). I attached the kernel configuration file for the
uni-processor case, to get the 'hang' one just has to throw over
the SMP-switch.
The machine hangs right after this message (boot -v).
SMP: AP CPU #1 Launched!
SMP: CPU1 apic_initialize():
lint0: 0x00010700 lint1: 0x00010400 TPR: 0x00000010 SVR: 0x000001ff
An aequivalent uni-processor kernel (with sym0, just without SMP)
runs flawlessly.
I attached the dmesg-outputs of a successfully booted SMP-kernel (ncr0
instead sym0) and and successfully booted UP-kernel (with sym0).
If anybody needs further information, ... just ask.
Any hints?
Thanks,
Andreas
--
Me no internet, only janitor, me just wax floors.
--azLHFNyN32YCQGCU
Content-Type: text/plain; charset=us-ascii
Content-Disposition: attachment; filename="mptable.out"
===============================================================================
MPTable, version 2.0.15
-------------------------------------------------------------------------------
MP Floating Pointer Structure:
location: BIOS
physical address: 0x000f0e70
signature: '_MP_'
length: 16 bytes
version: 1.1
checksum: 0x02
mode: Virtual Wire
-------------------------------------------------------------------------------
MP Config Table Header:
physical address: 0x000f0e84
signature: 'PCMP'
base table length: 308
version: 1.1
checksum: 0x2f
OEM ID: 'OEM00000'
Product ID: 'PROD00000000'
OEM table pointer: 0x00000000
OEM table size: 0
entry count: 30
local APIC address: 0xfee00000
extended table length: 0
extended table checksum: 0
-------------------------------------------------------------------------------
MP Config Base Table Entries:
--
Processors: APIC ID Version State Family Model Step Flags
0 0x11 BSP, usable 6 1 9 0xfbff
1 0x11 AP, usable 6 1 9 0xfbff
--
Bus: Bus ID Type
0 PCI
1 ISA
--
I/O APICs: APIC ID Version State Address
2 0x11 usable 0xfec00000
--
I/O Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#
ExtINT conforms conforms 1 0 2 0
INT conforms conforms 1 1 2 1
INT conforms conforms 1 0 2 2
INT conforms conforms 1 3 2 3
INT conforms conforms 1 4 2 4
INT conforms conforms 1 5 2 5
INT conforms conforms 1 6 2 6
INT conforms conforms 1 7 2 7
INT conforms conforms 1 8 2 8
INT conforms conforms 1 9 2 9
INT conforms conforms 1 10 2 10
INT conforms conforms 1 11 2 11
INT conforms conforms 1 12 2 12
INT conforms conforms 1 13 2 13
INT conforms conforms 1 14 2 14
INT conforms conforms 1 15 2 15
INT active-lo level 0 8:A 2 16
INT active-lo level 0 9:A 2 17
INT active-lo level 0 10:A 2 18
INT active-lo level 0 11:A 2 19
INT active-lo level 0 7:A 2 19
INT active-lo level 0 12:A 2 16
SMI conforms conforms 1 0 2 23
--
Local Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#
ExtINT conforms conforms 0 0:A 255 0
NMI conforms conforms 0 0:A 255 1
-------------------------------------------------------------------------------
# SMP kernel config file options:
# Required:
options SMP # Symmetric MultiProcessor Kernel
options APIC_IO # Symmetric (APIC) I/O
# Optional (built-in defaults will work in most cases):
#options NCPU=2 # number of CPUs
#options NBUS=2 # number of busses
#options NAPIC=1 # number of IO APICs
#options NINTR=24 # number of INTs
===============================================================================
--azLHFNyN32YCQGCU
Content-Type: text/plain; charset=us-ascii
Content-Disposition: attachment; filename=TSEGENERIC
# stripped down GENERIC
machine i386
#cpu I386_CPU
#cpu I486_CPU
#cpu I586_CPU
cpu I686_CPU
ident TSEGENERIC
maxusers 64
#makeoptions DEBUG=-g #Build kernel with gdb(1) debug symbols
# Size of the kernel message buffer. Should be N * pagesize.
options MSGBUF_SIZE=81920
#
options MATH_EMULATE #Support for x87 emulation
options INET #InterNETworking
options FFS #Berkeley Fast Filesystem
options FFS_ROOT #FFS usable as root device [keep this!]
options MFS #Memory Filesystem
options MD_ROOT #MD is a potential root device
options NFS #Network Filesystem
options NFS_ROOT #NFS usable as root device, "NFS" req'ed
options MSDOSFS #MSDOS Filesystem
options CD9660 #ISO 9660 Filesystem
options CD9660_ROOT #CD-ROM usable as root. "CD9660" req'ed
options PROCFS #Process filesystem
options COMPAT_43 #Compatible with BSD 4.3 [KEEP THIS!]
options SCSI_DELAY=15000 #Be pessimistic about Joe SCSI device
options UCONSOLE #Allow users to grab the console
options USERCONFIG #boot -c editor
options VISUAL_USERCONFIG #visual boot -c editor
options KTRACE #ktrace(1) syscall trace support
options SYSVSHM #SYSV-style shared memory
options SYSVMSG #SYSV-style message queues
options SYSVSEM #SYSV-style semaphores
options P1003_1B #Posix P1003_1B real-time extentions
options _KPOSIX_PRIORITY_SCHEDULING
options _KPOSIX_VERSION=199309L
# To make an SMP kernel, the next two are needed
#options SMP # Symmetric MultiProcessor Kernel
#options APIC_IO # Symmetric (APIC) I/O
# Optionally these may need tweaked, (defaults shown):
#options NCPU=2 # number of CPUs
#options NBUS=4 # number of busses
#options NAPIC=1 # number of IO APICs
#options NINTR=24 # number of INTs
device isa0
#device eisa0
device pci0
# Floppy drives
device fdc0 at isa? port IO_FD1 irq 6 drq 2
device fd0 at fdc0 drive 0
# ATA and ATAPI devices
#device ata0 at isa? port IO_WD1 irq 14
#device ata1 at isa? port IO_WD2 irq 15
#device ata2
#device atadisk0 # ATA disk drives
#device atapicd0 # ATAPI CDROM drives
#device atapifd0 # ATAPI floppy drives
#device atapist0 # ATAPI tape drives
#options ATA_STATIC_ID #Static device numbering
#options ATA_ENABLE_ATAPI_DMA #Enable DMA on ATAPI devices
# SCSI Controllers
# A single entry for any of these controllers (ahb, ahc, amd, ncr, etc...) is
# sufficient for any number of installed devices.
#device ahc0 # AHA2940 and onboard AIC7xxx devices
#device ncr0 # NCR/Symbios Logic
device sym0 # NCR/Symbios Logic (newer chipsets)
# SCSI peripherals
# Only one of each of these is needed, they are dynamically allocated.
device scbus0 # SCSI bus (required)
device da0 # Direct Access (disks)
device sa0 # Sequential Access (tape etc)
device cd0 # CD
device pass0 # Passthrough device (direct SCSI access)
# RAID controllers
#device amr0 # AMI MegaRAID
device mlx0 # Mylex DAC960 family
# atkbdc0 controls both the keyboard and the PS/2 mouse
device atkbdc0 at isa? port IO_KBD
device atkbd0 at atkbdc? irq 1
device psm0 at atkbdc? irq 12
device vga0 at isa? port ? conflicts
# splash screen/screen saver
pseudo-device splash
# syscons is the default console driver, resembling an SCO console
device sc0 at isa?
# Floating point support - do not disable.
device npx0 at nexus? port IO_NPX irq 13
# Power management support (see LINT for more options)
#device apm0 at nexus? disable flags 0x20 # Advanced Power Management
# Serial (COM) ports
device sio0 at isa? port IO_COM1 flags 0x10 irq 4
device sio1 at isa? port IO_COM2 irq 3
#device sio2 at isa? disable port IO_COM3 irq 5
#device sio3 at isa? disable port IO_COM4 irq 9
# Parallel port
device ppc0 at isa? port? irq 7
device ppbus0 # Parallel port bus (required)
device lpt0 at ppbus? # Printer
device plip0 at ppbus? # TCP/IP over parallel
device ppi0 at ppbus? # Parallel port interface device
#device vpo0 at ppbus? # Requires scbus and da0
# PCI Ethernet NICs.
#device de0 # DEC/Intel DC21x4x (``Tulip'')
device fxp0 # Intel EtherExpress PRO/100B (82557, 82558)
#device tx0 # SMC 9432TX (83c170 ``EPIC'')
#device vx0 # 3Com 3c590, 3c595 (``Vortex'')
#device wx0 # Intel Gigabit Ethernet Card (``Wiseman'')
# PCI Ethernet NICs that use the common MII bus controller code.
#device miibus0 # MII bus support
#device dc0 # DEC/Intel 21143 and various workalikes
#device rl0 # RealTek 8129/8139
#device sf0 # Adaptec AIC-6915 (``Starfire'')
#device sis0 # Silicon Integrated Systems SiS 900/SiS 7016
#device ste0 # Sundance ST201 (D-Link DFE-550TX)
#device tl0 # Texas Instruments ThunderLAN
#device vr0 # VIA Rhine, Rhine II
#device wb0 # Winbond W89C840F
#device xl0 # 3Com 3c90x (``Boomerang'', ``Cyclone'')
# Pseudo devices - the number indicates how many units to allocated.
pseudo-device loop # Network loopback
pseudo-device ether # Ethernet support
pseudo-device tun 16 # Packet tunnel.
pseudo-device pty 256 # Pseudo-ttys (telnet etc)
pseudo-device md # Memory "disks"
# The `bpf' pseudo-device enables the Berkeley Packet Filter.
# Be aware of the administrative consequences of enabling this!
pseudo-device bpf #Berkeley packet filter
--azLHFNyN32YCQGCU
Content-Type: text/plain; charset=us-ascii
Content-Disposition: attachment; filename="dmesg.smp"
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
FreeBSD 4.0-CURRENT #0: Tue Feb 1 00:57:03 CET 2000
toor@paert.tse-online.de:/iron/bsd/src/sys/compile/TSEGENERIC-SMP
Calibrating clock(s) ... TSC clock: 200554379 Hz, i8254 clock: 1193776 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
CPU: Pentium Pro (200.46-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x619 Stepping = 9
Features=0xfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV>
real memory = 134217728 (131072K bytes)
Physical memory chunk(s):
0x00001000 - 0x0009efff, 647168 bytes (158 pages)
0x002fa000 - 0x07febfff, 131014656 bytes (31986 pages)
config> di lnc0
No such device: lnc0
Invalid command or syntax. Type `?' for help.
config> di le0
No such device: le0
Invalid command or syntax. Type `?' for help.
config> di ie0
No such device: ie0
Invalid command or syntax. Type `?' for help.
config> di fe0
No such device: fe0
Invalid command or syntax. Type `?' for help.
config> di ex0
No such device: ex0
Invalid command or syntax. Type `?' for help.
config> di ed0
No such device: ed0
Invalid command or syntax. Type `?' for help.
config> di cs0
No such device: cs0
Invalid command or syntax. Type `?' for help.
config> di bt0
No such device: bt0
Invalid command or syntax. Type `?' for help.
config> di aic0
No such device: aic0
Invalid command or syntax. Type `?' for help.
config> di aha0
No such device: aha0
Invalid command or syntax. Type `?' for help.
config> di adv0
No such device: adv0
Invalid command or syntax. Type `?' for help.
config> q
avail memory = 127057920 (124080K bytes)
Programming 24 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
SMP: CPU0 apic_initialize():
lint0: 0x00000700 lint1: 0x00010400 TPR: 0x00000010 SVR: 0x000001ff
FreeBSD/SMP: Multiprocessor motherboard
cpu0 (BSP): apic id: 0, version: 0x00040011, at 0xfee00000
cpu1 (AP): apic id: 1, version: 0x00040011, at 0xfee00000
io0 (APIC): apic id: 2, version: 0x00170011, at 0xfec00000
bios32: Found BIOS32 Service Directory header at 0xc00faf30
bios32: Entry = 0xfb330 (c00fb330) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xb360
pnpbios: Found PnP BIOS data at 0xc00fc050
pnpbios: Entry = f0000:c078 Rev = 1.0
Other BIOS signatures found:
ACPI: 00000000
Preloaded elf kernel "kernel" at 0xc02de000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc02de0a8.
Pentium Pro MTRR support enabled
md0: Malloc disk
Creating DISK md0
Math emulator present
SMP: CPU0 bsp_apic_configure():
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000010 SVR: 0x000001ff
pci_open(1): mode 1 addr port (0x0cf8) is 0x8000005c
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=12378086)
npx0: <math processor> on motherboard
npx0: INT 16 interface
pci_open(1): mode 1 addr port (0x0cf8) is 0x00000000
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=12378086)
pcib0: <Host to PCI bridge> on motherboard
found-> vendor=0x8086, dev=0x1237, revid=0x02
class=06-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
found-> vendor=0x8086, dev=0x7000, revid=0x01
class=06-01-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x8086, dev=0x7010, revid=0x00
class=01-01-80, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[20]: type 1, range 32, base 0000f000, size 4
Freeing (NOT implemented) redirected PCI irq 11.
found-> vendor=0x8086, dev=0x1229, revid=0x04
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=16
map[10]: type 1, range 32, base e1908000, size 12
map[14]: type 1, range 32, base 00009100, size 5
map[18]: type 1, range 32, base e1800000, size 20
found-> vendor=0x8086, dev=0x0960, revid=0x05
class=06-04-00, hdrtype=0x01, mfdev=1
subordinatebus=1 secondarybus=1
Freeing (NOT implemented) redirected PCI irq 10.
found-> vendor=0x1069, dev=0x0010, revid=0x05
class=01-04-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
intpin=a, irq=17
map[10]: type 1, range 32, base e1904000, size 13
Freeing (NOT implemented) redirected PCI irq 9.
found-> vendor=0x1000, dev=0x000f, revid=0x14
class=01-00-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
intpin=a, irq=18
map[10]: type 1, range 32, base 00009200, size 8
map[14]: type 1, range 32, base e1909000, size 8
map[18]: type 1, range 32, base e190a000, size 12
found-> vendor=0x1000, dev=0x000f, revid=0x14
class=01-00-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
intpin=b, irq=5
map[10]: type 1, range 32, base 00009300, size 8
map[14]: type 1, range 32, base e1906000, size 8
map[18]: type 1, range 32, base e1907000, size 12
Freeing (NOT implemented) redirected PCI irq 11.
found-> vendor=0x102b, dev=0x051b, revid=0x00
class=03-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=16
map[10]: type 1, range 32, base e0000000, size 24
map[14]: type 1, range 32, base e1900000, size 14
map[18]: type 1, range 32, base e1000000, size 23
pci0: <PCI bus> on pcib0
isab0: <Intel 82371SB PCI to ISA bridge> at device 7.0 on pci0
I/O Recovery Timing: 8-bit 1 clocks, 16-bit 1 clocks
Extended BIOS: disabled
Lower BIOS: disabled
Coprocessor IRQ13: enabled
Mouse IRQ12: enabled
Interrupt Routing: A: IRQ11, B: IRQ10, C: IRQ9, D: IRQ5
MB0: , MB1:
isa0: <ISA bus> on isab0
pci0: Intel PIIX3 ATA controller (vendor=0x8086, dev=0x7010) at 7.1
fxp0: <Intel EtherExpress Pro 10/100B Ethernet> port 0x9100-0x911f mem 0xe1800000-0xe18fffff,0xe1908000-0xe1908fff irq 16 at device 8.0 on pci0
fxp0: Ethernet address 00:a0:c9:9f:3b:e5
bpf: fxp0 attached
pcib1: <PCI to PCI bridge (vendor=8086 device=0960)> at device 9.0 on pci0
pci1: <PCI bus> on pcib1
mlx0: <Mylex version 4 RAID interface> mem 0xe1904000-0xe1905fff irq 17 at device 9.1 on pci0
mlx0: DAC960PTL1, 1 channel, firmware 4.07-0-29, 8MB RAM
mlx0: Hardware ID 0x03020116
mlx0: Firmware ID 0x301d0704
mlx0: Configured/Actual channels 1/1
mlx0: Max Targets 16
mlx0: Max Tags 252
mlx0: Max System Drives 32
mlx0: Max Arms 8
mlx0: Max Spans 4
mlx0: DRAM/cache/flash/NVRAM size 8388608/6815744/524288/32768
mlx0: DRAM type 17
mlx0: Clock Speed 40ns
mlx0: Hardware Speed 360ns
mlx0: Max Commands 124
mlx0: Max SG Entries 33
mlx0: Max DP 504
mlx0: Max IOD 1024
mlx0: Max Comb 256
mlx0: Latency 12s
mlx0: SCSI Timeout 6s
mlx0: Min Free Lines 72
mlx0: Rate Constant 50
mlx0: MAXBLK 128
mlx0: Blocking Factor 1 sectors
mlx0: Cache Line Size 16 blocks
mlx0: SCSI Capability 40MHz, 16 bit
mlx0: Firmware Build Number 0
mlx0: Fault Management Type 0
mlx0: Features 0
mlxd0: <Mylex System Drive> on mlx0
mlxd0: 10242MB (20975616 sectors) RAID 5 (online)
Creating DISK mlxd0
mlxd1: <Mylex System Drive> on mlx0
mlxd1: 12288MB (25165824 sectors) RAID 5 (online)
Creating DISK mlxd1
mlxd2: <Mylex System Drive> on mlx0
mlxd2: 4952MB (10141696 sectors) RAID 0 (online)
Creating DISK mlxd2
ncr0: <ncr 53c875 fast20 wide scsi> port 0x9200-0x92ff mem 0xe190a000-0xe190afff,0xe1909000-0xe19090ff irq 18 at device 10.0 on pci0
ncr0: minsync=12, maxsync=137, maxoffs=16, 128 dwords burst, large dma fifo
ncr0: single-ended, open drain IRQ driver, using on-chip SRAM
ncr1: <ncr 53c875 fast20 wide scsi> port 0x9300-0x93ff mem 0xe1907000-0xe1907fff,0xe1906000-0xe19060ff irq 5 at device 10.1 on pci0
ncr1: minsync=12, maxsync=137, maxoffs=16, 128 dwords burst, large dma fifo
ncr1: single-ended, open drain IRQ driver, using on-chip SRAM
vga-pci0: <Matrox MGA 2164W graphics accelerator> mem 0xe1000000-0xe17fffff,0xe1900000-0xe1903fff,0xe0000000-0xe0ffffff irq 16 at device 12.0 on pci0
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <keyboard controller (i8042)> at port 0x60-0x6f on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
psm0: current command byte:0047
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:00fa
kbdc: RESET_AUX status:00aa
kbdc: RESET_AUX ID:0000
psm: status 00 02 64
psm: status 0a 03 c8
psm: status 0a 03 c8
psm: status 0a 03 c8
psm: status 10 00 64
psm: data c8 c2 50
psm: data 08 00 00
psm: status 00 02 64
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model MouseMan+, device ID 0-50, 3 buttons
psm0: config:00000000, flags:00000000, packet size:3
psm0: syncmask:08, syncbits:08
vga0: <Generic ISA VGA> at port 0x3b0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3b0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 60 4f 50 83 55 81
bf 1f 00 4f 0e 0f 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 60 4f 50 83 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 60 4f 50 83 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x200>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio0: irq maps: 0x41 0x51 0x41 0x41
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: irq maps: 0x41 0x49 0x41 0x41
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: parallel port found at 0x378
ppc0: EPP SPP
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
plip0: <PLIP network interface> on ppbus0
bpf: lp0 attached
ppi0: <Parallel I/O> on ppbus0
isa_probe_children: probing PnP devices
SMP: enabled INTs: 1, 3, 4, 5, 6, 7, 12, 16, 17, 18, apic_imen: 0x00f8ef05
BIOS Geometries:
0:020efe3f 0..526=527 cylinders, 0..254=255 heads, 1..63=63 sectors
0 accounted for
Device configuration finished.
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via IOAPIC #0 intpin 2
bpf: lo0 attached
Waiting 15 seconds for SCSI devices to settle
ncr0: restart (scsi reset).
ncr1: restart (scsi reset).
SMP: AP CPU #1 Launched!
SMP: CPU1 apic_initialize():
lint0: 0x00010700 lint1: 0x00010400 TPR: 0x00000010 SVR: 0x000001ff
(probe6:ncr0:0:6:0): INQUIRY. CDB: 12 1 80 0 ff 0
(probe6:ncr0:0:6:0): ILLEGAL REQUEST asc:24,0
(probe6:ncr0:0:6:0): Invalid field in CDB
Creating DISK da0
Creating DISK cd0
pass0 at ncr0 bus 0 target 0 lun 0
pass0: <IBM DCAS-34330W S65A> Fixed Direct Access SCSI-2 device
pass0: Serial Number F3V95882
pass0: 40.000MB/s transfers (20.000MHz, offset 15, 16bit)
pass1 at ncr0 bus 0 target 6 lun 0
pass1: <PIONEER CD-ROM DR-U10X 1.07> Removable CD-ROM SCSI-2 device
pass1: 10.000MB/s transfers (10.000MHz, offset 15)
Mounting root from ufs:/dev/da0s1a
(cd0:ncr0:0:6:0): READ CD RECORDED CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0
(cd0:ncr0:0:6:0): NOT READY asc:3a,0
(cd0:ncr0:0:6:0): Medium not present
cd0 at ncr0 bus 0 target 6 lun 0
cd0: <PIONEER CD-ROM DR-U10X 1.07> Removable CD-ROM SCSI-2 device
cd0: 10.000MB/s transfers (10.000MHz, offset 15)
cd0: Attempt to query device size failed: NOT READY, Medium not present
da0 at ncr0 bus 0 target 0 lun 0
da0: <IBM DCAS-34330W S65A> Fixed Direct Access SCSI-2 device
da0: Serial Number F3V95882
da0: 40.000MB/s transfers (20.000MHz, offset 15, 16bit)
da0: 4134MB (8467200 512 byte sectors: 255H 63S/T 527C)
da0s1: type 0xa5, start 63, end = 8466254, size 8466192 : OK
start_init: trying /sbin/init
mlxd2s1: type 0xa5, start 32, end = 10141695, size 10141664 : OK
mlxd1s1: type 0xa5, start 32, end = 25165823, size 25165792 : OK
mlxd0s1: type 0xa5, start 32, end = 20975615, size 20975584 : OK
mlxd1s1: type 0xa5, start 32, end = 25165823, size 25165792 : OK
mlxd0s1: type 0xa5, start 32, end = 20975615, size 20975584 : OK
mlxd0s1: type 0xa5, start 32, end = 20975615, size 20975584 : OK
mlxd0s1: type 0xa5, start 32, end = 20975615, size 20975584 : OK
mlxd0s1: type 0xa5, start 32, end = 20975615, size 20975584 : OK
mlxd1s1: type 0xa5, start 32, end = 25165823, size 25165792 : OK
mlxd0s1: type 0xa5, start 32, end = 20975615, size 20975584 : OK
--azLHFNyN32YCQGCU
Content-Type: text/plain; charset=us-ascii
Content-Disposition: attachment; filename="dmesg.up"
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
FreeBSD 4.0-CURRENT #0: Tue Feb 1 00:55:46 CET 2000
toor@paert.tse-online.de:/iron/bsd/src/sys/compile/TSEGENERIC
Calibrating clock(s) ... TSC clock: 200554308 Hz, i8254 clock: 1193776 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
Timecounter "TSC" frequency 200455432 Hz
CPU: Pentium Pro (200.46-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x619 Stepping = 9
Features=0xfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV>
real memory = 134217728 (131072K bytes)
Physical memory chunk(s):
0x00001000 - 0x0009efff, 647168 bytes (158 pages)
0x002ed000 - 0x07febfff, 131067904 bytes (31999 pages)
avail memory = 127111168 (124132K bytes)
bios32: Found BIOS32 Service Directory header at 0xc00faf30
bios32: Entry = 0xfb330 (c00fb330) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xb360
pnpbios: Found PnP BIOS data at 0xc00fc050
pnpbios: Entry = f0000:c078 Rev = 1.0
Other BIOS signatures found:
ACPI: 00000000
Preloaded elf kernel "kernel.up" at 0xc02d4000.
Pentium Pro MTRR support enabled
md0: Malloc disk
Creating DISK md0
Math emulator present
pci_open(1): mode 1 addr port (0x0cf8) is 0x8000005c
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=12378086)
npx0: <math processor> on motherboard
npx0: INT 16 interface
pci_open(1): mode 1 addr port (0x0cf8) is 0x00000000
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=12378086)
pcib0: <Host to PCI bridge> on motherboard
found-> vendor=0x8086, dev=0x1237, revid=0x02
class=06-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
found-> vendor=0x8086, dev=0x7000, revid=0x01
class=06-01-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x8086, dev=0x7010, revid=0x00
class=01-01-80, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[20]: type 1, range 32, base 0000f000, size 4
found-> vendor=0x8086, dev=0x1229, revid=0x04
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=11
map[10]: type 1, range 32, base e1908000, size 12
map[14]: type 1, range 32, base 00009100, size 5
map[18]: type 1, range 32, base e1800000, size 20
found-> vendor=0x8086, dev=0x0960, revid=0x05
class=06-04-00, hdrtype=0x01, mfdev=1
subordinatebus=1 secondarybus=1
found-> vendor=0x1069, dev=0x0010, revid=0x05
class=01-04-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
intpin=a, irq=10
map[10]: type 1, range 32, base e1904000, size 13
found-> vendor=0x1000, dev=0x000f, revid=0x14
class=01-00-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
intpin=a, irq=9
map[10]: type 1, range 32, base 00009200, size 8
map[14]: type 1, range 32, base e1909000, size 8
map[18]: type 1, range 32, base e190a000, size 12
found-> vendor=0x1000, dev=0x000f, revid=0x14
class=01-00-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
intpin=b, irq=5
map[10]: type 1, range 32, base 00009300, size 8
map[14]: type 1, range 32, base e1906000, size 8
map[18]: type 1, range 32, base e1907000, size 12
found-> vendor=0x102b, dev=0x051b, revid=0x00
class=03-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=11
map[10]: type 1, range 32, base e0000000, size 24
map[14]: type 1, range 32, base e1900000, size 14
map[18]: type 1, range 32, base e1000000, size 23
pci0: <PCI bus> on pcib0
Correcting Natoma config for non-SMP
Correcting Natoma config for non-SMP
isab0: <Intel 82371SB PCI to ISA bridge> at device 7.0 on pci0
I/O Recovery Timing: 8-bit 1 clocks, 16-bit 1 clocks
Extended BIOS: disabled
Lower BIOS: disabled
Coprocessor IRQ13: enabled
Mouse IRQ12: enabled
Interrupt Routing: A: IRQ11, B: IRQ10, C: IRQ9, D: IRQ5
MB0: , MB1:
isa0: <ISA bus> on isab0
pci0: Intel PIIX3 ATA controller (vendor=0x8086, dev=0x7010) at 7.1
fxp0: <Intel EtherExpress Pro 10/100B Ethernet> port 0x9100-0x911f mem 0xe1800000-0xe18fffff,0xe1908000-0xe1908fff irq 11 at device 8.0 on pci0
fxp0: Ethernet address 00:a0:c9:9f:3b:e5
bpf: fxp0 attached
pcib1: <PCI to PCI bridge (vendor=8086 device=0960)> at device 9.0 on pci0
pci1: <PCI bus> on pcib1
mlx0: <Mylex version 4 RAID interface> mem 0xe1904000-0xe1905fff irq 10 at device 9.1 on pci0
mlx0: DAC960PTL1, 1 channel, firmware 4.07-0-29, 8MB RAM
mlx0: Hardware ID 0x03020116
mlx0: Firmware ID 0x301d0704
mlx0: Configured/Actual channels 1/1
mlx0: Max Targets 16
mlx0: Max Tags 252
mlx0: Max System Drives 32
mlx0: Max Arms 8
mlx0: Max Spans 4
mlx0: DRAM/cache/flash/NVRAM size 8388608/6815744/524288/32768
mlx0: DRAM type 17
mlx0: Clock Speed 40ns
mlx0: Hardware Speed 360ns
mlx0: Max Commands 124
mlx0: Max SG Entries 33
mlx0: Max DP 504
mlx0: Max IOD 1024
mlx0: Max Comb 256
mlx0: Latency 12s
mlx0: SCSI Timeout 6s
mlx0: Min Free Lines 72
mlx0: Rate Constant 50
mlx0: MAXBLK 128
mlx0: Blocking Factor 1 sectors
mlx0: Cache Line Size 16 blocks
mlx0: SCSI Capability 40MHz, 16 bit
mlx0: Firmware Build Number 0
mlx0: Fault Management Type 0
mlx0: Features 0
mlxd0: <Mylex System Drive> on mlx0
mlxd0: 10242MB (20975616 sectors) RAID 5 (online)
Creating DISK mlxd0
mlxd1: <Mylex System Drive> on mlx0
mlxd1: 12288MB (25165824 sectors) RAID 5 (online)
Creating DISK mlxd1
mlxd2: <Mylex System Drive> on mlx0
mlxd2: 4952MB (10141696 sectors) RAID 0 (online)
Creating DISK mlxd2
sym0: <875> port 0x9200-0x92ff mem 0xe190a000-0xe190afff,0xe1909000-0xe19090ff irq 9 at device 10.0 on pci0
sym0: Symbios NVRAM, ID 7, Fast-20, SE, parity checking
sym0: open drain IRQ line driver, using on-chip SRAM
sym0: initial SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 05/4e/80/01/00/24
sym0: final SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 05/46/80/01/08/24
sym0: SCAN AT BOOT disabled for targets 1 2 3 4 5 8 9 10 11 12 13 14 15.
sym0: Delay (GEN=11): 243 msec, 36577 KHz
sym0: Delay (GEN=11): 263 msec, 33795 KHz
sym0: Delay (GEN=11): 263 msec, 33795 KHz
sym0: enabling clock multiplier
sym0: Downloading SCSI SCRIPTS.
sym1: <875> port 0x9300-0x93ff mem 0xe1907000-0xe1907fff,0xe1906000-0xe19060ff irq 5 at device 10.1 on pci0
sym1: chip clock is 40401KHz
sym1: Symbios NVRAM, ID 7, Fast-20, SE, parity checking
sym1: open drain IRQ line driver, using on-chip SRAM
sym1: initial SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 00/00/00/00/00/00
sym1: final SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 05/46/80/01/08/24
sym1: enabling clock multiplier
sym1: Downloading SCSI SCRIPTS.
vga-pci0: <Matrox MGA 2164W graphics accelerator> mem 0xe1000000-0xe17fffff,0xe1900000-0xe1903fff,0xe0000000-0xe0ffffff irq 11 at device 12.0 on pci0
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <keyboard controller (i8042)> at port 0x60-0x6f on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20000201004848.B27262>