From owner-freebsd-questions Sat Sep 9 12: 1:37 2000 Delivered-To: freebsd-questions@freebsd.org Received: from rapidnet.com (rapidnet.com [205.164.216.1]) by hub.freebsd.org (Postfix) with ESMTP id 3495E37B424 for ; Sat, 9 Sep 2000 12:01:30 -0700 (PDT) Received: (from pstapley@localhost) by rapidnet.com (8.9.3/8.9.3) id NAA68271 for questions@freebsd.org; Sat, 9 Sep 2000 13:01:29 -0600 (MDT) Date: Sat, 9 Sep 2000 13:01:29 -0600 (MDT) From: Peter Stapley Message-Id: <200009091901.NAA68271@rapidnet.com> To: questions@freebsd.org Subject: SMP Problems Sender: owner-freebsd-questions@FreeBSD.ORG Precedence: bulk X-Loop: FreeBSD.ORG Any ideas why I am not getting SMP to work? I ran mptable and took the values from there for the kernel config and it still does not work. Thanks, Pete Here is my dmesg: Copyright (c) 1992-2000 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 4.1-RELEASE #7: Sat Sep 9 11:37:22 GMT 2000 root@lucky.ihatejim.net:/usr/src/sys/compile/LUCKY Timecounter "i8254" frequency 1193182 Hz CPU: Pentium II/Pentium II Xeon/Celeron (266.44-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x634 Stepping = 4 Features=0x80fbff real memory = 67108864 (65536K bytes) avail memory = 62341120 (60880K bytes) Programming 24 pins in IOAPIC #0 IOAPIC #0 intpin 2 -> irq 0 IOAPIC #0 intpin 16 -> irq 11 IOAPIC #0 intpin 17 -> irq 10 IOAPIC #0 intpin 18 -> irq 9 FreeBSD/SMP: Multiprocessor motherboard cpu0 (BSP): apic id: 0, version: 0x00040011, at 0xfee00000 cpu1 (AP): apic id: 1, version: 0x00040011, at 0xfee00000 io0 (APIC): apic id: 2, version: 0x00170011, at 0xfec00000 Preloaded elf kernel "kernel" at 0xc02ea000. Preloaded userconfig_script "/boot/kernel.conf" at 0xc02ea09c. Pentium Pro MTRR support enabled md0: Malloc disk npx0: on motherboard npx0: INT 16 interface pcib0: on motherboard pci0: on pcib0 pcib1: at device 1.0 on pci0 pci1: on pcib1 isab0: at device 7.0 on pci0 isa0: on isab0 atapci0: port 0xffa0-0xffaf at device 7.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata1: at 0x170 irq 15 on atapci0 pci0: at 7.2 irq 0 Timecounter "PIIX" frequency 3579545 Hz chip1: port 0xfcb0-0xfcbf at device 7.3 on pci0 pci0: at 11.0 irq 11 tx0: port 0xec00-0xecff mem 0xfebef000-0xfebeffff irq 10 at device 12.0 on pci0 tx0: address 00:e0:29:0e:a7:6f, type SMC9432TX, Auto-Neg 100Mbps FD tx0: driver is using old-style compatability shims bktr0: mem 0xf69fe000-0xf69fefff irq 9 at device 13.0 on pci0 bktr0: Hauppauge Model 38101 B226 Hauppauge WinCast/TV, Philips NTSC tuner. pci0: (vendor=0x109e, dev=0x0878) at 13.1 irq 9 fdc0: at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 atkbdc0: at port 0x60,0x64 on isa0 atkbd0: flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 psm0: irq 12 on atkbdc0 psm0: model Generic PS/2 mouse, device ID 0 vga0: at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 sc0: at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 16550A sio1 at port 0x2f8-0x2ff irq 3 on isa0 sio1: type 16550A ppc0: at port 0x378-0x37f irq 7 on isa0 ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/8 bytes threshold ppi0: on ppbus0 lpt0: on ppbus0 lpt0: Interrupt-driven port plip0: on ppbus0 pcm0: at port 0x220-0x22f,0x530-0x537,0x388-0x38b,0x330-0x331,0x370-0x371 irq 5 drq 0,1 on isa0 unknown0: at port 0x201 on isa0 APIC_IO: Testing 8254 interrupt delivery APIC_IO: Broken MP table detected: 8254 is not connected to IOAPIC #0 intpin 2 APIC_IO: routing 8254 via 8259 and IOAPIC #0 intpin 0 SMP: AP CPU #1 Launched! ata1-slave: ata_command: timeout waiting for intr ata1-slave: identify failed ad0: 6485MB [13176/16/63] at ata0-master using UDMA33 acd0: CDROM at ata1-master using PIO3 Mounting root from ufs:/dev/ad0s1a Here is my config file: # # GENERIC -- Generic kernel configuration file for FreeBSD/i386 # # For more information on this file, please read the handbook section on # Kernel Configuration Files: # # http://www.FreeBSD.org/handbook/kernelconfig-config.html # # The handbook is also available locally in /usr/share/doc/handbook # if you've installed the doc distribution, otherwise always see the # FreeBSD World Wide Web server (http://www.FreeBSD.org/) for the # latest information. # # An exhaustive list of options and more detailed explanations of the # device lines is also present in the ./LINT configuration file. If you are # in doubt as to the purpose or necessity of a line, check first in LINT. # # $FreeBSD: src/sys/i386/conf/GENERIC,v 1.246.2.8 2000/07/20 02:51:02 msmith Exp $ machine i386 #cpu I386_CPU #cpu I486_CPU #cpu I586_CPU cpu I686_CPU ident LUCKY maxusers 32 #makeoptions DEBUG=-g #Build kernel with gdb(1) debug symbols options MATH_EMULATE #Support for x87 emulation options INET #InterNETworking #options INET6 #IPv6 communications protocols options FFS #Berkeley Fast Filesystem options FFS_ROOT #FFS usable as root device [keep this!] options SOFTUPDATES #Enable FFS soft updates support options MFS #Memory Filesystem options MD_ROOT #MD is a potential root device #options NFS #Network Filesystem #options NFS_ROOT #NFS usable as root device, NFS required #options MSDOSFS #MSDOS Filesystem options CD9660 #ISO 9660 Filesystem options CD9660_ROOT #CD-ROM usable as root, CD9660 required options PROCFS #Process filesystem options COMPAT_43 #Compatible with BSD 4.3 [KEEP THIS!] #options SCSI_DELAY=15000 #Delay (in ms) before probing SCSI options UCONSOLE #Allow users to grab the console options USERCONFIG #boot -c editor options VISUAL_USERCONFIG #visual boot -c editor options KTRACE #ktrace(1) support options SYSVSHM #SYSV-style shared memory options SYSVMSG #SYSV-style message queues options SYSVSEM #SYSV-style semaphores options P1003_1B #Posix P1003_1B real-time extensions options _KPOSIX_PRIORITY_SCHEDULING options ICMP_BANDLIM #Rate limit bad replies options KBD_INSTALL_CDEV # install a CDEV entry in /dev # To make an SMP kernel, the next two are needed options SMP # Symmetric MultiProcessor Kernel options APIC_IO # Symmetric (APIC) I/O # Optionally these may need tweaked, (defaults shown): options NCPU=2 # number of CPUs options NBUS=3 # number of busses options NAPIC=1 # number of IO APICs options NINTR=24 # number of INTs device isa #device eisa device pci # Floppy drives device fdc0 at isa? port IO_FD1 irq 6 drq 2 device fd0 at fdc0 drive 0 #device fd1 at fdc0 drive 1 # ATA and ATAPI devices device ata0 at isa? port IO_WD1 irq 14 device ata1 at isa? port IO_WD2 irq 15 device ata device atadisk # ATA disk drives device atapicd # ATAPI CDROM drives #device atapifd # ATAPI floppy drives #device atapist # ATAPI tape drives options ATA_STATIC_ID #Static device numbering #options ATA_ENABLE_ATAPI_DMA #Enable DMA on ATAPI devices # SCSI Controllers #device ahb # EISA AHA1742 family #device ahc # AHA2940 and onboard AIC7xxx devices #device amd # AMD 53C974 (Teckram DC-390(T)) #device dpt # DPT Smartcache - See LINT for options! #device isp # Qlogic family #device ncr # NCR/Symbios Logic #device sym # NCR/Symbios Logic (newer chipsets) #options SYM_SETUP_LP_PROBE_MAP=0x40 # Allow ncr to attach legacy NCR devices when # both sym and ncr are configured #device adv0 at isa? #device adw #device bt0 at isa? #device aha0 at isa? #device aic0 at isa? # SCSI peripherals device scbus # SCSI bus (required) #device da # Direct Access (disks) #device sa # Sequential Access (tape etc) #device cd # CD #device pass # Passthrough device (direct SCSI access) # RAID controllers #device ida # Compaq Smart RAID #device amr # AMI MegaRAID #device mlx # Mylex DAC960 family #device twe # 3ware Escalade # atkbdc0 controls both the keyboard and the PS/2 mouse device atkbdc0 at isa? port IO_KBD device atkbd0 at atkbdc? irq 1 flags 0x1 device psm0 at atkbdc? irq 12 device vga0 at isa? # splash screen/screen saver #pseudo-device splash # syscons is the default console driver, resembling an SCO console device sc0 at isa? flags 0x100 # Enable this and PCVT_FREEBSD for pcvt vt220 compatible console driver #device vt0 at isa? #options XSERVER # support for X server on a vt console #options FAT_CURSOR # start with block cursor # If you have a ThinkPAD, uncomment this along with the rest of the PCVT lines #options PCVT_SCANSET=2 # IBM keyboards are non-std # Floating point support - do not disable. device npx0 at nexus? port IO_NPX irq 13 # Power management support (see LINT for more options) #device apm0 at nexus? disable flags 0x20 # Advanced Power Management # PCCARD (PCMCIA) support #device card #device pcic0 at isa? irq 10 port 0x3e0 iomem 0xd0000 #device pcic1 at isa? irq 11 port 0x3e2 iomem 0xd4000 disable # Serial (COM) ports device sio0 at isa? port IO_COM1 flags 0x10 irq 4 device sio1 at isa? port IO_COM2 irq 3 #device sio2 at isa? disable port IO_COM3 irq 5 #device sio3 at isa? disable port IO_COM4 irq 9 # Parallel port device ppc0 at isa? irq 7 device ppbus # Parallel port bus (required) device lpt # Printer device plip # TCP/IP over parallel device ppi # Parallel port interface device #device vpo # Requires scbus and da # PCI Ethernet NICs. #device de # DEC/Intel DC21x4x (``Tulip'') #device fxp # Intel EtherExpress PRO/100B (82557, 82558) device tx # SMC 9432TX (83c170 ``EPIC'') #device vx # 3Com 3c590, 3c595 (``Vortex'') #device wx # Intel Gigabit Ethernet Card (``Wiseman'') # PCI Ethernet NICs that use the common MII bus controller code. #device miibus # MII bus support #device dc # DEC/Intel 21143 and various workalikes #device rl # RealTek 8129/8139 #device sf # Adaptec AIC-6915 (``Starfire'') #device sis # Silicon Integrated Systems SiS 900/SiS 7016 #device ste # Sundance ST201 (D-Link DFE-550TX) #device tl # Texas Instruments ThunderLAN #device vr # VIA Rhine, Rhine II #device wb # Winbond W89C840F #device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'') # ISA Ethernet NICs. #device ed0 at isa? port 0x280 irq 10 iomem 0xd8000 #device ex #device ep # WaveLAN/IEEE 802.11 wireless NICs. Note: the WaveLAN/IEEE really # exists only as a PCMCIA device, so there is no ISA attatement needed # and resources will always be dynamically assigned by the pccard code. #device wi # Aironet 4500/4800 802.11 wireless NICs. Note: the declaration below will # work for PCMCIA and PCI cards, as well as ISA cards set to ISA PnP # mode (the factory default). If you set the switches on your ISA # card for a manually chosen I/O address and IRQ, you must specify # those paremeters here. #device an # Xircom Ethernet #device xe # The probe order of these is presently determined by i386/isa/isa_compat.c. #device ie0 at isa? port 0x300 irq 10 iomem 0xd0000 #device fe0 at isa? port 0x300 #device le0 at isa? port 0x300 irq 5 iomem 0xd0000 #device lnc0 at isa? port 0x280 irq 10 drq 0 #device cs0 at isa? port 0x300 #device sn0 at isa? port 0x300 irq 10 # Pseudo devices - the number indicates how many units to allocated. pseudo-device loop # Network loopback pseudo-device ether # Ethernet support pseudo-device sl 1 # Kernel SLIP pseudo-device ppp 1 # Kernel PPP pseudo-device tun # Packet tunnel. pseudo-device pty # Pseudo-ttys (telnet etc) pseudo-device md # Memory "disks" pseudo-device gif 4 # IPv6 and IPv4 tunneling pseudo-device faith 1 # IPv6-to-IPv4 relaying (translation) # The `bpf' pseudo-device enables the Berkeley Packet Filter. # Be aware of the administrative consequences of enabling this! pseudo-device bpf #Berkeley packet filter # USB support #device uhci # UHCI PCI->USB interface #device ohci # OHCI PCI->USB interface #device usb # USB Bus (required) #device ugen # Generic #device uhid # "Human Interface Devices" #device ukbd # Keyboard #device ulpt # Printer #device umass # Disks/Mass storage - Requires scbus and da #device ums # Mouse # USB Ethernet, requires mii #device aue # ADMtek USB ethernet #device cue # CATC USB ethernet #device kue # Kawasaki LSI USB ethernet #Booktree Capture Card device bktr #Yamaha Sound Card device pcm To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message