Skip site navigation (1)Skip section navigation (2)
Date:      Sat, 29 Dec 2007 02:20:45 +0100
From:      Hans Petter Selasky <hselasky@c2i.net>
To:        freebsd-arm@freebsd.org
Subject:   FYI: AT91 UDP is now fully supported (and tested) by the FreeBSD P4 USB project
Message-ID:  <200712290220.45527.hselasky@c2i.net>

next in thread | raw e-mail | index | archive | help
Hi,

Here is what the "dmesg" looks like:

KDB: debugger backends: ddb
KDB: current backend: ddb
Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
=46reeBSD is a registered trademark of The FreeBSD Foundation.
=46reeBSD 8.0-CURRENT #304: Sat Dec 29 00:09:30 CET 2007
    hans_other@server0.selasky.org:/usr/obj/arm/usr/7-current/src/sys/custom
CPU: ARM920T rev 0 (ARM9TDMI core)
  DC enabled IC enabled WB enabled LABT
  16KB/32B 64-way Instruction cache
  16KB/32B 64-way write-back-locking-A Data cache
real memory  =3D 67108864 (64 MB)
avail memory =3D 61452288 (58 MB)
atmelarm0: <AT91 device bus> on motherboard
at91_st0: <ST> mem 0xdffffd00-0xdffffdff irq 1 on atmelarm0
at91_st0: watchdog registered, timeout intervall max. 64 sec
at91_pio0: <PIOA> mem 0xdffff400-0xdffff5ff irq 1 on atmelarm0
at91_pio0: ABSR: 0x60 OSR: 0 PSR:0x3938001f ODSR: 0
at91_pio0: [FILTER]
at91_pio1: <PIOB> mem 0xdffff600-0xdffff7ff irq 1 on atmelarm0
at91_pio1: ABSR: 0xff301 OSR: 0x2 PSR:0x3fc00cfe ODSR: 0
at91_pio1: [FILTER]
at91_pio2: <PIOC> mem 0xdffff800-0xdffff9ff irq 1 on atmelarm0
at91_pio2: ABSR: 0 OSR: 0x1000000a PSR:0xffffc075 ODSR: 0x10000000
at91_pio2: [FILTER]
at91_pio3: <PIOD> mem 0xdffffa00-0xdffffbff irq 1 on atmelarm0
at91_pio3: ABSR: 0 OSR: 0 PSR:0xfffffff ODSR: 0
at91_pio3: [FILTER]
at91_pmc0: <PMC> mem 0xdffffc00-0xdffffcff irq 1 on atmelarm0
at91_pmc0: Primary: 10000000 Hz PLLA: 180 MHz CPU: 180 MHz MCK: 60 MHz
at91_udp0: <AT91 integrated AT91_UDP controller> mem 0xdffb0000-0xdffb3fff =
irq=20
11,3 on atmelarm0
at91_udp0: [ITHREAD]
at91_udp0: [ITHREAD]
usb0 on at91_udp0
at91_mci0: <MCI mmc/sd host bridge> mem 0xdffb4000-0xdffb7fff irq 10 on=20
atmelarm0
at91_mci0: [ITHREAD]
mmc0: <mmc/sd bus> on at91_mci0
at91_twi0: <TWI> mem 0xdffb8000-0xdffbbfff irq 12 on atmelarm0
at91_twi0: [ITHREAD]
iicbus0: <Philips I2C bus> on at91_twi0
setting cwgr to 0x1a4a4
iicbus0: <Philips I2C bus> on at91_twi0
setting cwgr to 0x1a4a4
iicbus0: <unknown card> at addr 0
iic0: <I2C generic I/O> on iicbus0
icee0: <I2C EEPROM> at addr 0xa0 on iicbus0
ate0: <EMAC> mem 0xdffbc000-0xdffbffff irq 24 on atmelarm0
ate0: No MAC address setdevice_attach: ate0 attach returned 6
uart0: <DBGU> mem 0xdffff200-0xdffff3ff irq 1 on atmelarm0
uart0: [FILTER]m]X....=BD..=BD=B1..(115200,n,8,1)
uart1: <USART0> mem 0xdffc0000-0xdffc3fff irq 6 on atmelarm0
uart1: [FILTER]
uart2: <USARTff irq 9 on atmelarm0
uart4: [FILTER]
at91_spi0: <SPI> mem 0xdffe0000-0xdffe3fff irq 13 on atmelarm0
at91_spi0: [ITHREAD]
spibus0: <spibus bus> on at91_spi0
ohci0: <AT91 integrated OHCI controller> mem 0xdfe00000-0xdfefffff irq 23 o=
n=20
atmelarm0
ohci0: [ITHREAD]
usb1 on ohci0
Cannot get 100 Hz clock; using 100Hz
at91_st0: [FILTER]
Timecounter "AT91RM9200 timer" frequency 32768 Hz quality 1000
Timecounters tick every 10.000 msec
usb0: 12Mbps Full Speed USB v1.1
uhub0: <ATMEL DCI Root HUB, class 9/0, rev 2.00/1.00, addr 1> on usb0
uhub0: 1 port with 1 removable, self powered
usb1: 12Mbps Full Speed USB v1.0
uhub1: <Atmel OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usb1
uhub1: 2 ports with 2 removable, self powered
cdce0: <USB Ethernet Comm interface> on usb0
cdce0: Ethernet address: 01:23:45:67:89:ab
usbd_alloc_device: set address 2 failed (ignored)
usbd_alloc_device: getting device descriptor at addr 2 failed!
uhub1:uhub_reattach_port: could not allocate new device!
mmc0: setting transfer rate to 30.000MHz

"cdce0" is the device that currently appears when you plug the USB cable.

Precompiled ARM kernel at:

http://www.selasky.org/hans_petter/usb4bsd/snapshots/

=2D-HPS



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200712290220.45527.hselasky>