Date: Thu, 14 Aug 2008 02:08:06 -0700 From: Jeremy Chadwick <koitsu@FreeBSD.org> To: sam <samflanker@gmail.com> Cc: freebsd-hackers@freebsd.org, "Andrey V. Elsukov" <bu7cher@yandex.ru> Subject: Re: kern/98388: [ata] FreeBSD 6.1 - WDC WD1200JS SATA II disks are seen as older SATA Message-ID: <20080814090806.GA14589@eos.sc1.parodius.com> In-Reply-To: <48A3F478.8040901@gmail.com> References: <48A3D034.9090809@gmail.com> <48A3D43E.2070101@yandex.ru> <48A3D771.5010601@gmail.com> <20080814071616.GA758@eos.sc1.parodius.com> <20080814072713.GA1939@eos.sc1.parodius.com> <48A3E6AA.9000205@gmail.com> <20080814081102.GA7612@eos.sc1.parodius.com> <48A3F478.8040901@gmail.com>
next in thread | previous in thread | raw e-mail | index | archive | help
On Thu, Aug 14, 2008 at 01:01:44PM +0400, sam wrote: > Jeremy Chadwick wrote: >> On Thu, Aug 14, 2008 at 12:02:50PM +0400, sam wrote: >> >>> Jeremy Chadwick wrote: >>> >>>> On Thu, Aug 14, 2008 at 12:16:16AM -0700, Jeremy Chadwick wrote: >>>> >>>>> On Thu, Aug 14, 2008 at 10:57:53AM +0400, sam wrote: >>>>> >>>>>> Andrey V. Elsukov wrote: >>>>>> >>>>>>> sam wrote: >>>>>>> >>>>>>>> FreeBSD 7.0-STABLE FreeBSD 7.0-STABLE #5: Tue Aug 12 >>>>>>>> 13:54:27 MSD 2008 root@:/usr/obj/usr/src/sys/GENERIC >>>>>>>> i386 >>>>>>>> |-------------------------------------------------------------------- >>>>>>>> >>>>>>>> please, any solution ? >>>>>>>> >>>>>>> Probably speed is limited via jumpers on your hard drive. >>>>>>> >>>>>>> >>>>>> http://wdc.custhelp.com/cgi-bin/wdc.cfg/php/enduser/std_adp.php?p_faqid=1409&p_created=#jumper >>>>>> tried it >>>>>> >>>>>> without results >>>>>> >>>>> FWIW, the only time I've seen this happen is when there's a jumper >>>>> limiting the capability. You should have **removed** the OPT1 jumper, >>>>> and left any other jumpers alone. >>>>> >>>>> If you're absolutely sure the jumper is removed, I'll purchase one of >>>>> these drives and test it on an ICH7 (Supermicro PDSMi+) to confirm your >>>>> findings. >>>>> >>>> Actually, I don't need to -- I'm using WD5000AAKS disks myself on >>>> that exact system: >>>> >>>> atapci1: <Intel AHCI controller> port 0x30e8-0x30ef,0x30dc-0x30df,0x30e0-0x30e7,0x30d8-0x30db,0x30b0-0x30bf mem 0xe8600400-0xe86007ff irq 19 at device 31.2 on pci0 >>>> atapci1: [ITHREAD] >>>> atapci1: AHCI Version 01.10 controller with 4 ports detected >>>> ata2: <ATA channel 0> on atapci1 >>>> ata2: [ITHREAD] >>>> ata3: <ATA channel 1> on atapci1 >>>> ata3: [ITHREAD] >>>> ata4: <ATA channel 2> on atapci1 >>>> ata4: [ITHREAD] >>>> ata5: <ATA channel 3> on atapci1 >>>> ata5: [ITHREAD] >>>> >>>> ad6: 476940MB <WDC WD5000AAKS-00YGA0 12.01C02> at ata3-master SATA300 >>>> ad8: 476940MB <WDC WD5000AAKS-00TMA0 12.01C01> at ata4-master SATA300 >>>> >>> may issue in <Intel ICH7 SATA300 controller> driver ? >>> >>> ---------------------------------------------------- >>> atapci1: <Intel ICH7 SATA300 controller> port >>> 0xc880-0xc887,0xc800-0xc803,0xc480-0xc487,0xc400-0xc403,0xc080-0xc08f >>> irq 19 at device 31.2 on pci0 >>> ---------------------------------------------------- >>> >> >> Possibly. All my Intel ICH7 boards have AHCI capability, and I use it. >> See Chapter 4 here: >> >> http://www.supermicro.com/manuals/motherboard/3000/MNL-0889.pdf >> >> If your motherboard does, I'd recommend enabling it as well and see if >> things change. >> >> Regarding the "Enhanced" vs. "Compatible" mode: use Enhanced. On >> my boards, choosing Enhanced makes the AHCI and Intel MatrixRAID >> options appear. >> >> I'm fairly certain you don't need AHCI to get SATA300, though. >> >> I would recommend you re-check the jumpers on your disks to make sure >> you didn't make a mistake when adjusting things. >> >> > - HDD on position: all jumpers removed; > - SATA controller in Enchanced mode; > - no option AHCI in BIOS > > without results I'm out of ideas. Others will have to continue helping... -- | Jeremy Chadwick jdc at parodius.com | | Parodius Networking http://www.parodius.com/ | | UNIX Systems Administrator Mountain View, CA, USA | | Making life hard for others since 1977. PGP: 4BD6C0CB |
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20080814090806.GA14589>