Date: Wed, 9 Apr 1997 20:33:22 +0200 From: Andreas Klemm <andreas@klemm.gtn.com> To: smp@freebsd.org Subject: oops ... here is the verbose output of mptable for Titan Pro ATX Message-ID: <19970409203322.25058@klemm.gtn.com>
next in thread | raw e-mail | index | archive | help
Well, sorry, forgot to use the verbose switch in my first mail ... =============================================================================== MPTable, version 2.0.6 looking for EBDA pointer @ 0x040e, NOT found searching CMOS 'top of mem' @ 0x0009f800 (638K) searching default 'top of mem' @ 0x0009fc00 (639K) searching BIOS @ 0x000f0000 MP FPS found in BIOS @ physical addr: 0x000f0920 ------------------------------------------------------------------------------- MP Floating Pointer Structure: location: BIOS physical address: 0x000f0920 signature: '_MP_' length: 16 bytes version: 1.1 checksum: 0x57 mode: Virtual Wire ------------------------------------------------------------------------------- MP Config Table Header: physical address: 0x000f0934 signature: 'PCMP' base table length: 292 version: 1.1 checksum: 0xab OEM ID: 'OEM00000' Product ID: 'PROD00000000' OEM table pointer: 0x00000000 OEM table size: 0 entry count: 28 local APIC address: 0xfee00000 extended table length: 0 extended table checksum: 0 ------------------------------------------------------------------------------- MP Config Base Table Entries: -- Processors: APIC ID Version State Family Model Step Flags 1 0x11 BSP, usable 6 1 9 0xfbff 0 0x11 AP, usable 6 1 9 0xfbff -- Bus: Bus ID Type 0 ISA 1 PCI -- I/O APICs: APIC ID Version State Address 2 0x11 usable 0xfec00000 -- I/O Ints: Type Polarity Trigger Bus ID IRQ APIC ID INT# ExtINT conforms conforms 0 0 2 0 INT conforms conforms 0 1 2 1 INT conforms conforms 0 0 2 2 INT conforms conforms 0 3 2 3 INT conforms conforms 0 4 2 4 INT conforms conforms 0 5 2 5 INT conforms conforms 0 6 2 6 INT conforms conforms 0 7 2 7 INT conforms conforms 0 8 2 8 INT conforms conforms 0 9 2 9 INT conforms conforms 0 10 2 10 INT conforms conforms 0 11 2 11 INT conforms conforms 0 12 2 12 INT conforms conforms 0 13 2 13 INT conforms conforms 0 14 2 14 INT conforms conforms 0 15 2 15 INT active-lo level 1 14:A 2 16 INT active-lo level 1 13:A 2 17 INT active-lo level 1 12:A 2 18 INT active-lo level 1 11:A 2 19 SMI conforms conforms 0 0 2 23 -- Local Ints: Type Polarity Trigger Bus ID IRQ APIC ID INT# ExtINT active-hi edge 0 0 255 0 NMI active-hi edge 0 0 255 1 ------------------------------------------------------------------------------- # SMP kernel config file options: options SMP # Symmetric MultiProcessor Kernel options APIC_IO # Symmetric (APIC) I/O options NCPU=2 # number of CPUs options NBUS=2 # number of busses options NAPIC=1 # number of IO APICs options NINTR=24 # number of INTs options SMP_INVLTLB # #options SMP_PRIVPAGES # BROKEN, DO NOT use! #options SMP_AUTOSTART # BROKEN, DO NOT use! #options SERIAL_DEBUG # com port debug output ------------------------------------------------------------------------------- dmesg output: Copyright (c) 1992-1996 FreeBSD Inc. Copyright (c) 1982, 1986, 1989, 1991, 1993 The Regents of the University of California. All rights reserved. FreeBSD 3.0-SMP #0: Wed Apr 9 18:08:36 MET DST 1997 root@klemm.gtn.com:/usr/sys.bisdn/compile/BISDNSMP FreeBSD/SMP: Multiprocessor motherboard cpu0 (BSP): apic id: 1, version: 0x00040011 cpu1 (AP): apic id: 0, version: 0x00040011 io0 (APIC): apic id: 2, version: 0x00170011 Calibrating clock(s) relative to mc146818A clock ... i8254 clock: 1193092 Hz CLK_USE_I8254_CALIBRATION not specified - using default frequency CPU: Pentium Pro (686-class CPU) Origin = "GenuineIntel" Id = 0x619 Stepping=9 Features=0xfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,<b11>,MTRR,PGE,MCA,CMOV> real memory = 67108864 (65536K bytes) avail memory = 63975424 (62476K bytes) pcibus_setup(1): mode 1 addr port (0x0cf8) is 0x8000005c pcibus_setup(1a): mode1res=0x80000000 (0x80000000) pcibus_check: device 0 is there (id=12378086) Probing for devices on PCI bus 0: configuration mode 1 allows 32 devices. chip0 <Intel 82440FX (Natoma) PCI and memory controller> rev 2 on pci0:0:0 chip1 <Intel 82371SB PCI-ISA bridge> rev 1 on pci0:7:0 chip2 <Intel 82371SB IDE interface> rev 0 on pci0:7:1 mapreg[20] type=1 addr=0000f000 size=0010. I/O Recovery Timing: 8-bit 3.5 clocks, 16-bit 3.5 clocks Extended BIOS: disabled Lower BIOS: disabled Coprocessor IRQ13: disabled Mouse IRQ12: disabled Interrupt Routing: A: , B: , C: , D: MB0: , MB1: vx0 <3COM 3C900 Etherlink XL PCI> rev 0 int a irq 19 on pci0:11:0 Freeing (NOT implimented) irq 9 for ISA cards. mapreg[10] type=1 addr=00008000 size=0040. utp/aui/bnc[*utp*]: disable 'auto select' with DOS util! address 00:a0:24:cf:c8:38 bpf: vx0 attached vga0 <VGA-compatible display device> rev 1 int a irq 18 on pci0:12:0 Freeing (NOT implimented) irq 10 for ISA cards. mapreg[10] type=0 addr=e0800000 size=4000. mapreg[14] type=0 addr=e0000000 size=800000. ahc0 <Adaptec 2940 SCSI host adapter> rev 3 int a irq 17 on pci0:13:0 Freeing (NOT implimented) irq 11 for ISA cards. mapreg[10] type=1 addr=00008100 size=0100. mapreg[14] type=0 addr=e0804000 size=1000. reg16: ioaddr=0x8100 size=0x100 ahc0: Reading SEEPROM...done. internal50 cable is present internal68 cable not present brdctl == 0xac external cable not present eprom not present brdctl == 0x6c low byte termination enabled, high byte termination disabled ahc0: aic7870 Single Channel, SCSI Id=7, 16 SCBs ahc0: Downloading Sequencer Program...Done ahc0: Probing channel A Choosing drivers for scbus configured at 0 scbus0 at ahc0 bus 0 ahc0: target 0 synchronous at 10.0MHz, offset = 0xf sd is configured at 0 sd0 at scbus0 target 0 lun 0 sd0: <IBM DORS-32160 WA6A> type 0 fixed SCSI 2 sd0: Direct-Access 2063MB (4226725 512 byte sectors) sd0: with 6703 cyls, 5 heads, and an average 126 sectors/track ahc0: target 1 synchronous at 10.0MHz, offset = 0xf sd is configured at 1 sd1 at scbus0 target 1 lun 0 sd1: <IBM DORS-32160 WA6A> type 0 fixed SCSI 2 sd1: Direct-Access 2063MB (4226725 512 byte sectors) sd1: with 6703 cyls, 5 heads, and an average 126 sectors/track ahc0: target 2 synchronous at 10.0MHz, offset = 0xf sd is configured at 2 sd2 at scbus0 target 2 lun 0 sd2: <IBM DORS-32160 WA6A> type 0 fixed SCSI 2 sd2: Direct-Access 2063MB (4226725 512 byte sectors) sd2: with 6703 cyls, 5 heads, and an average 126 sectors/track ahc1 <Adaptec 2940 SCSI host adapter> rev 3 int a irq 16 on pci0:14:0 Freeing (NOT implimented) irq 15 for ISA cards. mapreg[10] type=1 addr=00008200 size=0100. mapreg[14] type=0 addr=e0805000 size=1000. reg16: ioaddr=0x8200 size=0x100 ahc1: Reading SEEPROM...done. internal50 cable not present internal68 cable not present brdctl == 0xec external cable not present eprom is present brdctl == 0xec low byte termination enabled, high byte termination disabled ahc1: aic7870 Single Channel, SCSI Id=7, 16 SCBs ahc1: Downloading Sequencer Program...Done ahc1: Probing channel A Choosing drivers for scbus configured at 1 scbus1 at ahc1 bus 0 pci0: uses 8413184 bytes of memory from e0000000 upto e0805fff. pci0: uses 592 bytes of I/O space from 8000 upto f00f. Probing for devices on the ISA bus: sc0: the current keyboard controller command byte 0047 kbdio: new command byte:0064 (set_controller...) kbdio: RESET_KBD return code:00fa kbdio: RESET_KBD status:00aa kbdio: new command byte:0047 (set_controller...) sc0 at 0x60-0x6f irq 1 on motherboard kbdio: new command byte:0046 (set_controller...) kbdio: new command byte:0047 (set_controller...) sc0: VGA color <6 virtual consoles, flags=0x0> lpt0 at 0x378-0x37f irq 7 on isa lpt0: Interrupt-driven port lp0: TCP/IP capable interface bpf: lp0 attached sio0 at 0x3f8-0x3ff irq 4 on isa sio0: type 16550A sio1 at 0x2f8-0x2ff irq 3 on isa sio1: type 16550A fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa fdc0: NEC 72065B fd0: 1.44MB 3.5in tel0 at 0xd80 irq 9 on isa bpf: ipi0 attached bpf: ipi1 attached tel0: card type Teles S0/16.3 npx0 on motherboard npx0: INT 16 interface imasks: bio c0030040, tty f000009a, net e0080200 BIOS Geometries: 0:0106fe3f 0..262=263 cylinders, 0..254=255 heads, 1..63=63 sectors 1:0106fe3f 0..262=263 cylinders, 0..254=255 heads, 1..63=63 sectors 2:0106fe3f 0..262=263 cylinders, 0..254=255 heads, 1..63=63 sectors 0 accounted for Device configuration finished. Considering FFS root f/s. configure() finished. Enabled INTs: 1, 2, 3, 4, 6, 7, 8, 9, 16, 17, 19, imen: 0x00f4fc21 bpf: tun0 attached bpf: lo0 attached IP packet filtering initialized, divert disabled, logging limited to 100 packets/entry sd0s1: type 0x6, start 63, end = 1028159, size 1028097 : OK sd0s2: type 0x5, start 1028160, end = 2056319, size 1028160 : OK sd0s3: type 0xa5, start 2056320, end = 4225094, size 2168775 : OK sd0s5: type 0x6, start 1028223, end = 2056319, size 1028097 : OK SMP: All idle procs online. sd1s1: type 0xa5, start 63, end = 4225094, size 4225032 : OK sd2s1: type 0xa5, start 63, end = 4225094, size 4225032 : OK sd2s1: type 0xa5, start 63, end = 4225094, size 4225032 : OK Assigned: TEI = 0xe1 = 112 SMP: Starting 1st AP! SMP: AP CPU #1 LAUNCHED!! Starting Scheduling... SMP: TADA! CPU #1 made it into the scheduler!. SMP: All 2 CPU's are online! =============================================================================== -- andreas@klemm.gtn.com /\/\___ Wiechers & Partner Datentechnik GmbH Andreas Klemm ___/\/\/ Support Unix -- andreas.klemm@wup.de pgp p-key http://www-swiss.ai.mit.edu/~bal/pks-toplev.html >>> powered by <<< ftp://sunsite.unc.edu/pub/Linux/system/Printing/aps-491.tgz >>> FreeBSD <<<
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?19970409203322.25058>