Skip site navigation (1)Skip section navigation (2)
Date:      Tue, 16 Apr 2002 01:50:13 -0000
From:      "Jordan Breeding" <jordan.breeding@attbi.com>
To:        <freebsd-scsi@freebsd.org>
Subject:   Trouble installing 5.0-DP1 to a Tyan Thunder K7 (aic7xxx)...
Message-ID:  <!~!UENERkVCMDkAAQACAAAAAAAAAAAAAAAAABgAAAAAAAAAjQHXypTRWUeX0Da3WGxUUMKAAAAQAAAAB5S/GF2FpEylB6XRir51UAEAAAAA@attbi.com>

Next in thread | Raw E-Mail | Index | Archive | Help
This is a multi-part message in MIME format.

------=_NextPart_000_000B_01C1E4E9.0D1509C0
Content-Type: text/plain;
	charset="us-ascii"
Content-Transfer-Encoding: 7bit

Hello,

  I have recently aquired a new Tyan Thunder K7 (S2462UNG) with on-board
Adaptec scsi.  Everything with the scsi works great in DOS, Linux and
Windows.  However, I hate using Windows, and Linux is giving me lots of
trouble with this board in regards to rebooting and shuting down
properly.  I was playing with some old FreeBSD CDROMs I had laying
around the other and it appeared that from the CDROM at least FreeBSD
can correctly reboot this machine.  While I still use linux for the bulk
of my work I decided I could at least do a small install of FreeBSD on
my virtually unused SCSI 4 GB hd at Channel A, id 0 and go from there.
So I first decided to boot from the 5.0-DP1 iso which I downloaded, but
this didn't work as I expected, the disc booted, found my IDE hard
drive, found my SCSI CDROM and went into the sysinstal without ever
finding my SCSI hard drive.  So then I tried the 4.5 discs which I had
laying around.  I no longer have my 4.4 discs but something tells me
those wouldn't have done much better, and I would want to be able to do
CVS pulls of current anyway which was the original breakage I noticed.
So since I do not have a serial console laying around at the moment I
decided to do a boot -v and then boot the "live" filesystem and dump the
dmesg to a floppy.  In this email (sorry about the length) I have
included a dmesg output from Linux (which works as far as the SCSI goes,
I am using 2.4.19-pre6 with some other patches and am using the new
aic7xxx driver from Justin Gibbs) as well as the dmesg from a boot -v
showing the failure of the FreeBSD 5.0-DP1 boot to find my Channel A and
hence failure to find my hard drive.  Thanks for any help, please let me
know if there is anything I can try to fix this.  I do not have room
anywhere on my current IDE drive for FreeBSD so I need to try and
eventually get a fixed install method so that I can install to the scsi
drive.  Thanks for any help which you can give me in solving this
situation.

Jordan Breeding

PS - I am not on this list so please Cc: me on replies.

------=_NextPart_000_000B_01C1E4E9.0D1509C0
Content-Type: text/plain;
	name="dmesg_linux.txt"
Content-Transfer-Encoding: quoted-printable
Content-Disposition: attachment;
	filename="dmesg_linux.txt"

IOS-e820: 000000001ffffc00 - 0000000020000000 (ACPI NVS)
 BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
found SMP MP-table at 000f74d0
hm, page 000f7000 reserved twice.
hm, page 000f8000 reserved twice.
hm, page 0009f000 reserved twice.
hm, page 000a0000 reserved twice.
On node 0 totalpages: 131056
zone(0): 4096 pages.
zone(1): 126960 pages.
zone(2): 0 pages.
ACPI: Searched entire block, no RSDP was found.
ACPI: RSDP located at physical address c00f7470
RSD PTR  v0 [PTLTD ]
__va_range(0x1fffd505, 0x68): idx=3D8 mapped at ffff6000
ACPI table found: RSDT v1 [PTLTD    RSDT   1540.0]
__va_range(0x1ffffb2e, 0x24): idx=3D8 mapped at ffff6000
__va_range(0x1ffffb2e, 0x74): idx=3D8 mapped at ffff6000
ACPI table found: FACP v1 [TYAN   GUINNESS 1540.0]
__va_range(0x1ffffba2, 0x24): idx=3D8 mapped at ffff6000
__va_range(0x1ffffba2, 0x5e): idx=3D8 mapped at ffff6000
ACPI table found: APIC v1 [PTLTD    APIC   1540.0]
__va_range(0x1ffffba2, 0x5e): idx=3D8 mapped at ffff6000
LAPIC (acpi_id[0x0000] id[0x1] enabled[1])
CPU 0 (0x0100) enabledProcessor #1 Pentium(tm) Pro APIC version 16

LAPIC (acpi_id[0x0001] id[0x0] enabled[1])
CPU 1 (0x0000) enabledProcessor #0 Pentium(tm) Pro APIC version 16

IOAPIC (id[0x2] address[0xfec00000] global_irq_base[0x0])
INT_SRC_OVR (bus[0] irq[0x0] global_irq[0x2] polarity[0x1] trigger[0x1])
LAPIC_NMI (acpi_id[0x0000] polarity[0x1] trigger[0x1] lint[0x1])
LAPIC_NMI (acpi_id[0x0001] polarity[0x1] trigger[0x1] lint[0x1])
2 CPUs total
Local APIC address fee00000
Enabling the CPU's according to the ACPI table
Intel MultiProcessor Specification v1.4
    Virtual Wire compatibility mode.
OEM ID: TYAN     Product ID: GUINNESS     APIC at: 0xFEE00000
I/O APIC #2 Version 17 at 0xFEC00000.
Processors: 2
Phoenix Technologies Ltd.Guinness-8   03/21/2002TyanTHUNDER K7EVT1       =
  0123456789TyanTHUNDER K7EVT1         Kernel command line: ro =
root=3D/dev/hda7 profile=3D2 nmi_watchdog=3D1 acpismp=3Dforce =
video=3Dradeon:1280x1024-8@85 3
Initializing CPU#0
Detected 1592.916 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 3178.49 BogoMIPS
Memory: 509716k/524224k available (2672k kernel code, 14120k reserved, =
645k data, 348k init, 0k highmem)
Dentry-cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: Before vendor init, caps: 0383fbff c1cbfbff 00000000, vendor =3D 2
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After vendor init, caps: 0383fbff c1cbfbff 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU:     After generic, caps: 0383fbff c1cbfbff 00000000 00000000
CPU:             Common caps: 0383fbff c1cbfbff 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
CPU: Before vendor init, caps: 0383fbff c1cbfbff 00000000, vendor =3D 2
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After vendor init, caps: 0383fbff c1cbfbff 00000000 00000000
Intel machine check reporting enabled on CPU#0.
CPU:     After generic, caps: 0383fbff c1cbfbff 00000000 00000000
CPU:             Common caps: 0383fbff c1cbfbff 00000000 00000000
CPU0: AMD Athlon(tm) MP 1900+ stepping 02
per-CPU timeslice cutoff: 731.57 usecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Booting processor 1/0 eip 2000
Initializing CPU#1
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 3185.04 BogoMIPS
CPU: Before vendor init, caps: 0383fbff c1cbfbff 00000000, vendor =3D 2
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After vendor init, caps: 0383fbff c1cbfbff 00000000 00000000
Intel machine check reporting enabled on CPU#1.
CPU:     After generic, caps: 0383fbff c1cbfbff 00000000 00000000
CPU:             Common caps: 0383fbff c1cbfbff 00000000 00000000
CPU1: AMD Athlon(tm) Processor stepping 02
Total of 2 processors activated (6363.54 BogoMIPS).
ENABLING IO-APIC IRQs
Setting 2 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 2 ... ok.
init IO_APIC IRQs
 IO-APIC (apicid-pin) 2-0, 2-5, 2-7, 2-10, 2-11, 2-20, 2-21, 2-22, 2-23 =
not connected.
..TIMER: vector=3D0x31 pin1=3D2 pin2=3D0
activating NMI Watchdog ... done.
testing NMI watchdog ... CPU#0: NMI appears to be stuck!
number of MP IRQ sources: 20.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................

IO APIC #2......
.... register #00: 02000000
.......    : physical APIC id: 02
.... register #01: 00170011
.......     : max redirection entries: 0017
.......     : PRQ implemented: 0
.......     : IO APIC version: 0011
.... register #02: 00000000
.......     : arbitration: 00
.... IRQ redirection table:
 NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:  =20
 00 000 00  1    0    0   0   0    0    0    00
 01 003 03  0    0    0   0   0    1    1    39
 02 003 03  0    0    0   0   0    1    1    31
 03 003 03  0    0    0   0   0    1    1    41
 04 003 03  0    0    0   0   0    1    1    49
 05 000 00  1    0    0   0   0    0    0    00
 06 003 03  0    0    0   0   0    1    1    51
 07 000 00  1    0    0   0   0    0    0    00
 08 003 03  0    0    0   0   0    1    1    59
 09 003 03  0    0    0   0   0    1    1    61
 0a 000 00  1    0    0   0   0    0    0    00
 0b 000 00  1    0    0   0   0    0    0    00
 0c 003 03  0    0    0   0   0    1    1    69
 0d 003 03  0    0    0   0   0    1    1    71
 0e 003 03  0    0    0   0   0    1    1    79
 0f 003 03  0    0    0   0   0    1    1    81
 10 003 03  1    1    0   1   0    1    1    89
 11 003 03  1    1    0   1   0    1    1    91
 12 003 03  1    1    0   1   0    1    1    99
 13 003 03  1    1    0   1   0    1    1    A1
 14 000 00  1    0    0   0   0    0    0    00
 15 000 00  1    0    0   0   0    0    0    00
 16 000 00  1    0    0   0   0    0    0    00
 17 000 00  1    0    0   0   0    0    0    00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ6 -> 0:6
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1592.9701 MHz.
..... host bus clock speed is 265.4950 MHz.
cpu: 0, clocks: 2654950, slice: 884983
CPU0<T0:2654944,T1:1769952,D:9,S:884983,C:2654950>
cpu: 1, clocks: 2654950, slice: 884983
CPU1<T0:2654944,T1:884976,D:2,S:884983,C:2654950>
checking TSC synchronization across CPUs: passed.
Waiting on wait_init_idle (map =3D 0x2)
All processors have done init_idle
mtrr: your CPUs had inconsistent fixed MTRR settings
mtrr: probably your BIOS does not setup all CPUs
PCI: PCI BIOS revision 2.10 entry at 0xfd7c0, last bus=3D1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI->APIC IRQ transform: (B0,I7,P3) -> 19
PCI->APIC IRQ transform: (B0,I11,P0) -> 19
PCI->APIC IRQ transform: (B0,I12,P0) -> 16
PCI->APIC IRQ transform: (B0,I13,P0) -> 16
PCI->APIC IRQ transform: (B0,I13,P1) -> 17
PCI->APIC IRQ transform: (B0,I15,P0) -> 18
PCI->APIC IRQ transform: (B0,I16,P0) -> 19
PCI->APIC IRQ transform: (B1,I5,P0) -> 17
BIOS failed to enable PCI standards compliance, fixing this error.
I/O APIC: AMD Errata #22 may be present. In the event of instability try
        : booting with the "noapic" option.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12 (20020219) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
Journalled Block Device driver loaded
cdfs 0.5c loaded.
NTFS driver v1.1.22 [Flags: R/W]
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
ACPI: Core Subsystem version [20011018]
ACPI: Subsystem enabled
ACPI: System firmware supports S0 S1 S4 S5
Processor[0]: C0 C1
Processor[1]: C0 C1
ACPI: Power Button (FF) found
ACPI: Multiple power buttons detected, ignoring fixed-feature
ACPI: Power Button (CM) found
ACPI: Sleep Button (FF) found
i2c-core.o: i2c core module version 2.6.3 (20020322)
i2c-dev.o: i2c /dev entries driver module version 2.6.3 (20020322)
i2c-proc.o version 2.6.3 (20020322)
i2c-amd756.o version 2.6.3 (20020322)
i2c-dev.o: Registered 'SMBus AMD7X6 adapter at 80e0' as minor 0
i2c-amd756.o: AMD756/766 bus detected and initialized
i2c-isa.o version 2.6.3 (20020322)
i2c-dev.o: Registered 'ISA main adapter' as minor 1
i2c-isa.o: ISA bus access for i2c modules initialized.
radeonfb: ref_clk=3D2700, ref_div=3D12, xclk=3D23000 defaults
Console: switching to colour frame buffer device 160x64
radeonfb: ATI Radeon 7500 QW  DDR SGRAM 64 MB
radeonfb: DVI port CRT monitor connected
radeonfb: CRT port no monitor connected
pty: 2048 Unix98 ptys configured
w83781d.o version 2.6.3 (20020322)
eeprom.o version 2.6.3 (20020322)
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ =
SERIAL_PCI ISAPNP SERIAL_ACPI enabled
ttyS00 at 0x03f8 (irq =3D 4) is a 16550A
ttyS01 at 0x02f8 (irq =3D 3) is a 16550A
ttyS04 at port 0x1400 (irq =3D 16) is a 16550A
Real Time Clock Driver v1.10e
Non-volatile memory driver v1.1
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with =
idebus=3Dxx
AMD7411: IDE controller on PCI bus 00 dev 39
AMD7411: chipset revision 1
AMD7411: not 100% native mode: will probe irqs later
AMD7411: disabling single-word DMA support (revision < C4)
    ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio
hda: ST380021A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=3D9729/255/63, =
UDMA(100)
Partition check:
 /dev/ide/host0/bus0/target0/lun0: p1 p2 p3 < p5 p6 p7 p8 p9 p10 p11 p12 =
p13 >
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
00:0f.0: 3Com PCI 3c982 Dual Port Server Cyclone at 0x2000. Vers =
LK1.1.16
00:10.0: 3Com PCI 3c982 Dual Port Server Cyclone at 0x2080. Vers =
LK1.1.16
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
Universal TUN/TAP device driver 1.4 (C)1999-2001 Maxim Krasnyansky
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: Detected AMD 760MP chipset
agpgart: AGP aperture is 64M @ 0xec000000
[drm] AGP 0.99 on AMD Irongate @ 0xec000000 64MB
[drm] Initialized radeon 1.1.1 20010405 on minor 0
SCSI subsystem driver Revision: 1.00
Loading Adaptec I2O RAID: Version 2.4 Build 5
Detecting Adaptec I2O RAID controllers...
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.5
        <Adaptec aic7899 Ultra160 SCSI adapter>
        aic7899: Ultra160 Wide Channel A, SCSI Id=3D7, 32/253 SCBs

scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.5
        <Adaptec aic7899 Ultra160 SCSI adapter>
        aic7899: Ultra160 Wide Channel B, SCSI Id=3D7, 32/253 SCBs

  Vendor: IBM       Model: DCAS-34330W       Rev: S65A
  Type:   Direct-Access                      ANSI SCSI revision: 02
(scsi0:A:0): 40.000MB/s transfers (20.000MHz, offset 15, 16bit)
scsi0:A:0:0: Tagged Queuing enabled.  Depth 253
  Vendor: TEAC      Model: CD-R55S           Rev: 1.0R
  Type:   CD-ROM                             ANSI SCSI revision: 02
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sda: 8467200 512-byte hdwr sectors (4335 MB)
 /dev/scsi/host0/bus0/target0/lun0: p1 p2
Attached scsi CD-ROM sr0 at scsi1, channel 0, id 5, lun 0
(scsi1:A:5): 10.000MB/s transfers (10.000MHz, offset 15)
sr0: scsi-1 drive
Uniform CD-ROM driver Revision: 3.12
Creative EMU10K1 PCI Audio Driver, version 0.18, 17:24:28 Apr 11 2002
emu10k1: EMU10K1 rev 8 model 0x8027 found, IO at 0x2400-0x241f, IRQ 19
ac97_codec: AC97  codec, id: 0x5452:0x4123 (TriTech TR A5)
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-ohci.c: USB OHCI at membase 0xc00dc000, IRQ 19
usb-ohci.c: usb-00:07.4, Advanced Micro Devices [AMD] AMD-766 =
[ViperPlus] USB
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 4 ports detected
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 32Kbytes
TCP: Hash tables configured (established 16384 bind 21845)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
IPv6 v0.8 for NET4.0
IPv6 over IPv4 tunneling driver
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 348k freed
hub.c: USB new device connect on bus1/1, assigned device number 2
input0: USB HID v1.00 Mouse [0430:0100] on usb1:2.0
hub.c: USB new device connect on bus1/2, assigned device number 3
input1: USB HID v1.00 Keyboard [0430:0005] on usb1:3.0
Adding Swap: 2097136k swap-space (priority -1)
Adding Swap: 2097136k swap-space (priority -2)
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,7), internal journal
kjournald starting.  Commit interval 5 seconds
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on sd(8,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,13), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,12), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,9), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,10), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,8), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
eth0: no IPv6 routers present
eth1: no IPv6 routers present

------=_NextPart_000_000B_01C1E4E9.0D1509C0
Content-Type: text/plain;
	name="dmesg_freebsd.txt"
Content-Transfer-Encoding: quoted-printable
Content-Disposition: attachment;
	filename="dmesg_freebsd.txt"

Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD 5.0-DP1 #1: Sun Apr  7 11:02:24 GMT 2002
    murray@builder.freebsdmall.com:/usr/src/sys/i386/compile/BOOTMFS
Preloaded elf kernel "/kernel" at 0xc0815000.
Preloaded mfs_root "/mfsroot" at 0xc0815090.
Calibrating clock(s) ... TSC clock: 1592628231 Hz, i8254 clock: 1192980 =
Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254"  frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
Timecounter "TSC"  frequency 1592902403 Hz
CPU: AMD Athlon(tm) MP 1900+ (1592.90-MHz 686-class CPU)
  Origin =3D "AuthenticAMD"  Id =3D 0x662  Stepping =3D 2
  =
Features=3D0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE=
,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
  AMD Features=3D0xc0480000<MP,AMIE,DSP,3DNow!>
Data TLB: 32 entries, fully associative
Instruction TLB: 16 entries, fully associative
L1 data cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
L1 instruction cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way =
associative
L2 internal cache: 256 kbytes, 64 bytes/line, 1 lines/tag, 8-way =
associative
real memory  =3D 536805376 (524224K bytes)
Physical memory chunk(s):
0x00001000 - 0x0009dfff, 643072 bytes (157 pages)
0x0083c000 - 0x1ffe7fff, 528138240 bytes (128940 pages)
avail memory =3D 514035712 (501988K bytes)
bios32: Found BIOS32 Service Directory header at 0xc00f7440
bios32: Entry =3D 0xfd6a0 (c00fd6a0)  Rev =3D 0  Len =3D 1
pcibios: PCI BIOS entry at 0xfd6a0+0x120
pnpbios: Found PnP BIOS data at 0xc00f7490
pnpbios: Entry =3D f0000:9ea4  Rev =3D 1.0
Other BIOS signatures found:
null: <null device, zero device>
mem: <memory & I/O>
Pentium Pro MTRR support enabled
md0: Preloaded image </mfsroot> 4423680 bytes at 0xc03dbf00
Creating DISK md0
pci_open(1):	mode 1 addr port (0x0cf8) is 0x80003850
pci_open(1a):	mode1res=3D0x80000000 (0x80000000)
pci_cfgcheck:	device 0 [class=3D060000] [hdr=3D00] is there =
(id=3D700c1022)
Using $PIR table, 268435454 entries at 0xc00fdef0
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> at pcibus 0 on motherboard
pci0: physical bus=3D0
	map[10]: type 3, range 32, base ec000000, size 26, enabled
	map[14]: type 3, range 32, base e8004000, size 12, enabled
	map[18]: type 4, range 32, base 00002430, size  2, port disabled
found->	vendor=3D0x1022, dev=3D0x700c, revid=3D0x11
	bus=3D0, slot=3D0, func=3D0
	class=3D06-00-00, hdrtype=3D0x00, mfdev=3D0
found->	vendor=3D0x1022, dev=3D0x700d, revid=3D0x00
	bus=3D0, slot=3D1, func=3D0
	class=3D06-04-00, hdrtype=3D0x01, mfdev=3D0
found->	vendor=3D0x1022, dev=3D0x7410, revid=3D0x02
	bus=3D0, slot=3D7, func=3D0
	class=3D06-01-00, hdrtype=3D0x00, mfdev=3D1
	map[20]: type 4, range 32, base 0000f000, size  4, enabled
found->	vendor=3D0x1022, dev=3D0x7411, revid=3D0x01
	bus=3D0, slot=3D7, func=3D1
	class=3D01-01-8a, hdrtype=3D0x00, mfdev=3D0
found->	vendor=3D0x1022, dev=3D0x7413, revid=3D0x01
	bus=3D0, slot=3D7, func=3D3
	class=3D06-80-00, hdrtype=3D0x00, mfdev=3D0
	map[10]: type 1, range 32, base 000dc000, size 12, enabled
found->	vendor=3D0x1022, dev=3D0x7414, revid=3D0x07
	bus=3D0, slot=3D7, func=3D4
	class=3D0c-03-10, hdrtype=3D0x00, mfdev=3D0
	intpin=3Dd, irq=3D11
	map[10]: type 4, range 32, base 00002400, size  5, enabled
found->	vendor=3D0x1102, dev=3D0x0002, revid=3D0x08
	bus=3D0, slot=3D11, func=3D0
	class=3D04-01-00, hdrtype=3D0x00, mfdev=3D1
	intpin=3Da, irq=3D11
	powerspec 1  supports D0 D1 D2 D3  current D0
	map[10]: type 4, range 32, base 00002438, size  3, enabled
found->	vendor=3D0x1102, dev=3D0x7002, revid=3D0x08
	bus=3D0, slot=3D11, func=3D1
	class=3D09-80-00, hdrtype=3D0x00, mfdev=3D1
	powerspec 1  supports D0 D1 D2 D3  current D0
	map[10]: type 1, range 32, base e8003000, size  8, enabled
	map[14]: type 4, range 32, base 00001400, size  8, enabled
	map[18]: type 4, range 32, base 00001000, size  8, enabled
	map[1c]: type 4, range 32, base 00002440, size  3, enabled
found->	vendor=3D0x11c1, dev=3D0x0480, revid=3D0x00
	bus=3D0, slot=3D12, func=3D0
	class=3D07-03-03, hdrtype=3D0x00, mfdev=3D0
	intpin=3Da, irq=3D5
	powerspec 2  supports D0 D2 D3  current D0
	map[10]: type 4, range 32, base 00001800, size  8, enabled
	map[14]: type 1, range 64, base e8001000, size 12, enabled
found->	vendor=3D0x9005, dev=3D0x00cf, revid=3D0x01
	bus=3D0, slot=3D13, func=3D0
	class=3D01-00-00, hdrtype=3D0x00, mfdev=3D1
	intpin=3Da, irq=3D5
	powerspec 2  supports D0 D3  current D0
	map[10]: type 4, range 32, base 00001c00, size  8, enabled
	map[14]: type 1, range 64, base e8002000, size 12, enabled
found->	vendor=3D0x9005, dev=3D0x00cf, revid=3D0x01
	bus=3D0, slot=3D13, func=3D1
	class=3D01-00-00, hdrtype=3D0x00, mfdev=3D1
	intpin=3Db, irq=3D10
	powerspec 2  supports D0 D3  current D0
	map[10]: type 4, range 32, base 00002000, size  7, enabled
	map[14]: type 1, range 32, base e8003400, size  7, enabled
found->	vendor=3D0x10b7, dev=3D0x9805, revid=3D0x78
	bus=3D0, slot=3D15, func=3D0
	class=3D02-00-00, hdrtype=3D0x00, mfdev=3D0
	intpin=3Da, irq=3D7
	powerspec 2  supports D0 D1 D2 D3  current D0
	map[10]: type 4, range 32, base 00002080, size  7, enabled
	map[14]: type 1, range 32, base e8003800, size  7, enabled
found->	vendor=3D0x10b7, dev=3D0x9805, revid=3D0x78
	bus=3D0, slot=3D16, func=3D0
	class=3D02-00-00, hdrtype=3D0x00, mfdev=3D0
	intpin=3Da, irq=3D11
	powerspec 2  supports D0 D1 D2 D3  current D0
pci0: <PCI bus> on pcib0
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pcib1:   secondary bus     1
pcib1:   subordinate bus   1
pcib1:   I/O decode        0x3000-0x3fff
pcib1:   memory decode     0xe8100000-0xe81fffff
pcib1:   prefetched decode 0xf0000000-0xf7ffffff
pci1: physical bus=3D1
	map[10]: type 3, range 32, base f0000000, size 27, enabled
	map[14]: type 4, range 32, base 00003000, size  8, enabled
	map[18]: type 1, range 32, base e8100000, size 16, enabled
found->	vendor=3D0x1002, dev=3D0x5157, revid=3D0x00
	bus=3D1, slot=3D5, func=3D0
	class=3D03-00-00, hdrtype=3D0x00, mfdev=3D0
	intpin=3Da, irq=3D255
	powerspec 2  supports D0 D1 D2 D3  current D0
pci1: <PCI bus> on pcib1
pci1: <display, VGA> at device 5.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <AMD 766 ATA100 controller> port 0xf000-0xf00f at device 7.1 on =
pci0
ata0: iobase=3D0x01f0 altiobase=3D0x03f6 bmaddr=3D0xf000
ata0: mask=3D03 ostat0=3D50 ostat2=3D00
ata0-master: ATAPI 00 00
ata0-slave: ATAPI 00 00
ata0: mask=3D03 stat0=3D50 stat1=3D00
ata0-master: ATA 01 a5
ata0: devices=3D01
ata0: at 0x1f0 irq 14 on atapci0
ata1: iobase=3D0x0170 altiobase=3D0x0376 bmaddr=3D0xf008
ata1: mask=3D03 ostat0=3D20 ostat2=3D30
ata1-master: ATAPI 20 20
ata1-slave: ATAPI 30 30
ata1: mask=3D03 stat0=3D20 stat1=3D30
ata1-master: ATA 25 25
ata1-slave: ATA 25 25
ata1: devices=3D00
ata1: at 0x170 irq 15 on atapci0
pci0: <bridge, PCI-unknown> at device 7.3 (no driver attached)
ohci0: <AMD-766 USB Controller> mem 0xdc000-0xdcfff irq 11 at device 7.4 =
on pci0
usb0: OHCI version 1.0, legacy support
usb0: SMM does not respond, resetting
usb0: <AMD-766 USB Controller> on ohci0
usb0: USB revision 1.0
uhub0: AMD OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 4 ports with 4 removable, self powered
ums0: Sun Microsystems Type 6 USB mouse, rev 1.00/1.02, addr 2, iclass =
3/1
ums0: 3 buttons
ukbd0: Sun Microsystems Type 6 USB keyboard, rev 1.00/1.02, addr 3, =
iclass 3/1
kbd: new array size 4
kbd1 at ukbd0
kbd1: ukbd0, generic (0), config:0x0, flags:0x1d0000
pci0: <multimedia, audio> at device 11.0 (no driver attached)
pci0: <input device> at device 11.1 (no driver attached)
sio0: irq maps: 0x1001 0x1021 0x1001 0x1001
sio0: <Lucent kermit based PCI Modem> port =
0x2440-0x2447,0x1000-0x10ff,0x1400-0x14ff mem 0xe8003000-0xe80030ff irq =
5 at device 12.0 on pci0
sio0: moving to sio4
sio4: type 16550A
ahc0: <Adaptec aic7899 Ultra160 SCSI adapter> port 0x1800-0x18ff mem =
0xe8001000-0xe8001fff irq 5 at device 13.0 on pci0
ahc0: Reading SEEPROM...done.
ahc0: Manual SE Termination
ahc0: Manual LVD Termination
ahc0: BIOS eeprom is present
ahc0: Primary Low Byte termination Enabled
ahc0: Primary High Byte termination Enabled
ahc0: Downloading Sequencer Program... 419 instructions downloaded
device_probe_and_attach: ahc0 attach returned 12
ahc0: <Adaptec aic7899 Ultra160 SCSI adapter> port 0x1c00-0x1cff mem =
0xe8002000-0xe8002fff irq 10 at device 13.1 on pci0
ahc0: Reading SEEPROM...done.
ahc0: Manual SE Termination
ahc0: Manual LVD Termination
ahc0: BIOS eeprom is present
ahc0: Primary Low Byte termination Enabled
ahc0: Primary High Byte termination Enabled
ahc0: Downloading Sequencer Program... 419 instructions downloaded
aic7899: Ultra160 Wide Channel B, SCSI Id=3D7, 32/255 SCBs
pci0: <network, ethernet> at device 15.0 (no driver attached)
pci0: <network, ethernet> at device 16.0 (no driver attached)
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
ex_isa_identify()
pnpbios: 16 devices, largest 126 bytes
PNP0c01: adding fixed memory32 range 0-0x9ffff, size=3D0xa0000
PNP0c01: adding fixed memory32 range 0xe4000-0xfffff, size=3D0x1c000
PNP0c01: adding fixed memory32 range 0x100000-0x1fffffff, =
size=3D0x1ff00000
pnpbios: handle 0 device ID PNP0c01 (010cd041)
PNP0200: adding io range 0-0xf, size=3D0x10, align=3D0x1
PNP0200: adding io range 0x81-0x8f, size=3D0xf, align=3D0x1
PNP0200: adding io range 0xc0-0xdf, size=3D0x20, align=3D0x1
PNP0200: adding dma mask 0x10
pnpbios: handle 1 device ID PNP0200 (0002d041)
PNP0000: adding io range 0x20-0x21, size=3D0x2, align=3D0x1
PNP0000: adding io range 0xa0-0xa1, size=3D0x2, align=3D0x1
PNP0000: adding irq mask 0x4
pnpbios: handle 2 device ID PNP0000 (0000d041)
PNP0100: adding io range 0x40-0x43, size=3D0x4, align=3D0x1
PNP0100: adding irq mask 0x1
pnpbios: handle 3 device ID PNP0100 (0001d041)
PNP0b00: adding io range 0x70-0x71, size=3D0x2, align=3D0x1
PNP0b00: adding irq mask 0x100
pnpbios: handle 4 device ID PNP0b00 (000bd041)
PNP0303: adding io range 0x60-0x60, size=3D0x1, align=3D0x1
PNP0303: adding io range 0x64-0x64, size=3D0x1, align=3D0x1
PNP0303: adding irq mask 0x2
pnpbios: handle 5 device ID PNP0303 (0303d041)
PNP0c04: adding io range 0xf0-0xff, size=3D0x10, align=3D0x1
PNP0c04: adding irq mask 0x2000
pnpbios: handle 6 device ID PNP0c04 (040cd041)
PNP0800: adding io range 0x61-0x61, size=3D0x1, align=3D0x1
pnpbios: handle 7 device ID PNP0800 (0008d041)
PNP0a03: adding io range 0xcf8-0xcff, size=3D0x8, align=3D0x1
pnpbios: handle 8 device ID PNP0a03 (030ad041)
PNP0c02: adding io range 0x4d0-0x4d1, size=3D0x2, align=3D0x1
pnpbios: handle 9 device ID PNP0c02 (020cd041)
PNP0c02: adding memory32 range 0xe0000-0xe3fff, size=3D0x4000, =
align=3D0x4000
pnpbios: handle 10 device ID PNP0c02 (020cd041)
PNP0c02: adding fixed memory32 range 0xfec00000-0xfec0ffff, =
size=3D0x10000
PNP0c02: adding fixed memory32 range 0xfee00000-0xfee00fff, =
size=3D0x1000
pnpbios: handle 11 device ID PNP0c02 (020cd041)
PNP0c02: adding fixed memory32 range 0xd1600-0xd17ff, size=3D0x200
pnpbios: handle 13 device ID PNP0c02 (020cd041)
PNP0501: adding io range 0x3f8-0x3ff, size=3D0x8, align=3D0x1
PNP0501: adding irq mask 0x10
pnpbios: handle 16 device ID PNP0501 (0105d041)
PNP0501: adding io range 0x2f8-0x2ff, size=3D0x8, align=3D0x1
PNP0501: adding irq mask 0x8
pnpbios: handle 17 device ID PNP0501 (0105d041)
PNP0700: adding io range 0x3f0-0x3f5, size=3D0x6, align=3D0x1
PNP0700: adding io range 0x3f7-0x3f7, size=3D0x1, align=3D0x1
PNP0700: adding irq mask 0x40
PNP0700: adding dma mask 0x4
pnpbios: handle 21 device ID PNP0700 (0007d041)
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROMs> at iomem =
0xe0000-0xe3fff,0xd1800-0xd1fff,0xc0000-0xcbfff on isa0
adv0 failed to probe on isa0
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0 failed to probe at port 0x134-0x137 on isa0
aic0 failed to probe at port 0x140-0x15f on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0067
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
psm0: current command byte:0067
psm0: failed to reset the aux device.
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x330
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x334
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x230
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x234
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x130
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x134
bt0 failed to probe at port 0x134-0x137 on isa0
cs0 failed to probe at port 0x300-0x31f on isa0
ed0 failed to probe at port 0x280-0x29f iomem 0xd8000 irq 10 on isa0
fdc0: <enhanced floppy controller (i82077, NE72065 or clone)> at port =
0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
fe0 failed to probe at port 0x300-0x31f on isa0
ie0 failed to probe at port 0x300 iomem 0xd0000 irq 10 on isa0
le0 failed to probe at port 0x300 iomem 0xd0000 irq 5 on isa0
lnc0 failed to probe at port 0x280 irq 10 drq 0 on isa0
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
pmtimer0 failed to probe on isa0
ppc0: parallel port not found.
ppc0: <Parallel port> failed to probe at irq 7 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=3D0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio0: irq maps: 0x1041 0x1051 0x1041 0x1041
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: irq maps: 0x1041 0x1049 0x1041 0x1041
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: Cannot allocate irq
sn0 failed to probe at port 0x300-0x30f irq 10 on isa0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on =
isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81=20
bf 1f 00 4f 0d 0e 00 00 06 90 9c 8e 8f 28 1f 96=20
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c=20
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff=20
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81=20
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96=20
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c=20
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff=20
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81=20
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96=20
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c=20
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff=20
vt0 failed to probe on isa0
isa_probe_children: probing PnP devices
adv1: Invalid baseport of 0x0 specified. Nearest valid baseport is =
0x100.  Failing probe.
adv1: Invalid baseport of 0x20 specified. Nearest valid baseport is =
0x100.  Failing probe.
adv1: Invalid baseport of 0x40 specified. Nearest valid baseport is =
0x100.  Failing probe.
adv1: Invalid baseport of 0x70 specified. Nearest valid baseport is =
0x100.  Failing probe.
unknown: <PNP0303> can't assign resources (port)
unknown: <PNP0303> at port 0x60 on isa0
adv1: Invalid baseport of 0xf0 specified. Nearest valid baseport is =
0x100.  Failing probe.
adv1: Invalid baseport of 0x61 specified. Nearest valid baseport is =
0x100.  Failing probe.
unknown: <PNP0800> failed to probe at port 0x61 on isa0
adv1: Invalid baseport of 0xcf8 specified. Nearest valid baseport is =
0x330.  Failing probe.
adv1: Invalid baseport of 0x4d0 specified. Nearest valid baseport is =
0x330.  Failing probe.
unknown: <PNP0c02> can't assign resources (memory)
unknown: <PNP0c02> at iomem 0xe0000-0xe3fff on isa0
unknown: <PNP0501> can't assign resources (port)
unknown: <PNP0501> at port 0x3f8-0x3ff on isa0
unknown: <PNP0501> can't assign resources (port)
unknown: <PNP0501> at port 0x2f8-0x2ff on isa0
unknown: <PNP0700> can't assign resources (port)
unknown: <PNP0700> at port 0x3f0-0x3f5 on isa0
BIOS Geometries:
 0:03fefe3f 0..1022=3D1023 cylinders, 0..254=3D255 heads, 1..63=3D63 =
sectors
 1:020efe3f 0..526=3D527 cylinders, 0..254=3D255 heads, 1..63=3D63 =
sectors
 0 accounted for
Device configuration finished.
bpf: lo0 attached
ad0: success setting UDMA5 on AMD chip
Creating DISK ad0
ad0: <ST380021A/3.10> ATA-5 disk at ata0-master
ad0: 76319MB (156301488 sectors), 155061 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, UDMA100
ad0: piomode=3D4 dmamode=3D2 udmamode=3D5 cblid=3D1
Waiting 15 seconds for SCSI devices to settle
(noperiph:ahc0:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted.
(ahc0:A:5:0): Sending SDTR period c, offset 7f
(ahc0:A:5:0): Received SDTR period 19, offset f
	Filtered to period 19, offset f
ahc0: target 5 synchronous at 10.0MHz, offset =3D 0xf
(ahc0:A:5:0): Sending SDTR period 19, offset f
(ahc0:A:5:0): Received SDTR period 19, offset f
	Filtered to period 19, offset f
Creating DISK cd0
Mounting root from ufs:/dev/md0c
md0: invalid primary partition table: Dangerously Dedicated (ignored)
start_init: trying /sbin/init
start_init: trying /sbin/oinit
start_init: trying /sbin/init.bak
start_init: trying /stand/sysinstall
cd0 at ahc0 bus 0 target 5 lun 0
cd0: <TEAC CD-R55S 1.0R> Removable CD-ROM SCSI-2 device=20
cd0: Serial Number 8709911C
cd0: 10.000MB/s transfers (10.000MHz, offset 15)
cd0: cd present [330064 x 2048 byte records]
ahc1: <Adaptec aic7899 Ultra160 SCSI adapter> port 0x1800-0x18ff mem =
0xe8001000-0xe8001fff irq 5 at device 13.0 on pci0
ahc1: Reading SEEPROM...done.
ahc1: Manual SE Termination
ahc1: Manual LVD Termination
ahc1: BIOS eeprom is present
ahc1: Primary Low Byte termination Enabled
ahc1: Primary High Byte termination Enabled
ahc1: Downloading Sequencer Program... 419 instructions downloaded
device_probe_and_attach: ahc1 attach returned 12
aha0: status reg test failed ff
ppc0: parallel port not found.
sn0: Cannot allocate irq
adv1: Invalid baseport of 0x61 specified. Nearest valid baseport is =
0x100.  Failing probe.
ahc1: <Adaptec aic7899 Ultra160 SCSI adapter> port 0x1800-0x18ff mem =
0xe8001000-0xe8001fff irq 5 at device 13.0 on pci0
ahc1: Reading SEEPROM...done.
ahc1: Manual SE Termination
ahc1: Manual LVD Termination
ahc1: BIOS eeprom is present
ahc1: Primary Low Byte termination Enabled
ahc1: Primary High Byte termination Enabled
ahc1: Downloading Sequencer Program... 419 instructions downloaded
device_probe_and_attach: ahc1 attach returned 12
ahc1: <Adaptec aic7899 Ultra160 SCSI adapter> port 0x1800-0x18ff mem =
0xe8001000-0xe8001fff irq 5 at device 13.0 on pci0
ahc1: Reading SEEPROM...done.
ahc1: Manual SE Termination
ahc1: Manual LVD Termination
ahc1: BIOS eeprom is present
ahc1: Primary Low Byte termination Enabled
ahc1: Primary High Byte termination Enabled
ahc1: Downloading Sequencer Program... 419 instructions downloaded
device_probe_and_attach: ahc1 attach returned 12
ahc1: <Adaptec aic7899 Ultra160 SCSI adapter> port 0x1800-0x18ff mem =
0xe8001000-0xe8001fff irq 5 at device 13.0 on pci0
ahc1: Reading SEEPROM...done.
ahc1: Manual SE Termination
ahc1: Manual LVD Termination
ahc1: BIOS eeprom is present
ahc1: Primary Low Byte termination Enabled
ahc1: Primary High Byte termination Enabled
ahc1: Downloading Sequencer Program... 419 instructions downloaded
device_probe_and_attach: ahc1 attach returned 12
ahc1: <Adaptec aic7899 Ultra160 SCSI adapter> port 0x1800-0x18ff mem =
0xe8001000-0xe8001fff irq 5 at device 13.0 on pci0
ahc1: Reading SEEPROM...done.
ahc1: Manual SE Termination
ahc1: Manual LVD Termination
ahc1: BIOS eeprom is present
ahc1: Primary Low Byte termination Enabled
ahc1: Primary High Byte termination Enabled
ahc1: Downloading Sequencer Program... 419 instructions downloaded
device_probe_and_attach: ahc1 attach returned 12
ahc1: <Adaptec aic7899 Ultra160 SCSI adapter> port 0x1800-0x18ff mem =
0xe8001000-0xe8001fff irq 5 at device 13.0 on pci0
ahc1: Reading SEEPROM...done.
ahc1: Manual SE Termination
ahc1: Manual LVD Termination
ahc1: BIOS eeprom is present
ahc1: Primary Low Byte termination Enabled
ahc1: Primary High Byte termination Enabled
ahc1: Downloading Sequencer Program... 419 instructions downloaded
device_probe_and_attach: ahc1 attach returned 12
ahc1: <Adaptec aic7899 Ultra160 SCSI adapter> port 0x1800-0x18ff mem =
0xe8001000-0xe8001fff irq 5 at device 13.0 on pci0
ahc1: Reading SEEPROM...done.
ahc1: Manual SE Termination
ahc1: Manual LVD Termination
ahc1: BIOS eeprom is present
ahc1: Primary Low Byte termination Enabled
ahc1: Primary High Byte termination Enabled
ahc1: Downloading Sequencer Program... 419 instructions downloaded
device_probe_and_attach: ahc1 attach returned 12
ahc1: <Adaptec aic7899 Ultra160 SCSI adapter> port 0x1800-0x18ff mem =
0xe8001000-0xe8001fff irq 5 at device 13.0 on pci0
ahc1: Reading SEEPROM...done.
ahc1: Manual SE Termination
ahc1: Manual LVD Termination
ahc1: BIOS eeprom is present
ahc1: Primary Low Byte termination Enabled
ahc1: Primary High Byte termination Enabled
ahc1: Downloading Sequencer Program... 419 instructions downloaded
device_probe_and_attach: ahc1 attach returned 12
ahc1: <Adaptec aic7899 Ultra160 SCSI adapter> port 0x1800-0x18ff mem =
0xe8001000-0xe8001fff irq 5 at device 13.0 on pci0
ahc1: Reading SEEPROM...done.
ahc1: Manual SE Termination
ahc1: Manual LVD Termination
ahc1: BIOS eeprom is present
ahc1: Primary Low Byte termination Enabled
ahc1: Primary High Byte termination Enabled
ahc1: Downloading Sequencer Program... 419 instructions downloaded
device_probe_and_attach: ahc1 attach returned 12
ahc1: <Adaptec aic7899 Ultra160 SCSI adapter> port 0x1800-0x18ff mem =
0xe8001000-0xe8001fff irq 5 at device 13.0 on pci0
ahc1: Reading SEEPROM...done.
ahc1: Manual SE Termination
ahc1: Manual LVD Termination
ahc1: BIOS eeprom is present
ahc1: Primary Low Byte termination Enabled
ahc1: Primary High Byte termination Enabled
ahc1: Downloading Sequencer Program... 419 instructions downloaded
device_probe_and_attach: ahc1 attach returned 12
ahc1: <Adaptec aic7899 Ultra160 SCSI adapter> port 0x1800-0x18ff mem =
0xe8001000-0xe8001fff irq 5 at device 13.0 on pci0
ahc1: Reading SEEPROM...done.
ahc1: Manual SE Termination
ahc1: Manual LVD Termination
ahc1: BIOS eeprom is present
ahc1: Primary Low Byte termination Enabled
ahc1: Primary High Byte termination Enabled
ahc1: Downloading Sequencer Program... 419 instructions downloaded
device_probe_and_attach: ahc1 attach returned 12
ahc1: <Adaptec aic7899 Ultra160 SCSI adapter> port 0x1800-0x18ff mem =
0xe8001000-0xe8001fff irq 5 at device 13.0 on pci0
ahc1: Reading SEEPROM...done.
ahc1: Manual SE Termination
ahc1: Manual LVD Termination
ahc1: BIOS eeprom is present
ahc1: Primary Low Byte termination Enabled
ahc1: Primary High Byte termination Enabled
ahc1: Downloading Sequencer Program... 419 instructions downloaded
device_probe_and_attach: ahc1 attach returned 12
ahc1: <Adaptec aic7899 Ultra160 SCSI adapter> port 0x1800-0x18ff mem =
0xe8001000-0xe8001fff irq 5 at device 13.0 on pci0
ahc1: Reading SEEPROM...done.
ahc1: Manual SE Termination
ahc1: Manual LVD Termination
ahc1: BIOS eeprom is present
ahc1: Primary Low Byte termination Enabled
ahc1: Primary High Byte termination Enabled
ahc1: Downloading Sequencer Program... 419 instructions downloaded
device_probe_and_attach: ahc1 attach returned 12
ahc1: <Adaptec aic7899 Ultra160 SCSI adapter> port 0x1800-0x18ff mem =
0xe8001000-0xe8001fff irq 5 at device 13.0 on pci0
ahc1: Reading SEEPROM...done.
ahc1: Manual SE Termination
ahc1: Manual LVD Termination
ahc1: BIOS eeprom is present
ahc1: Primary Low Byte termination Enabled
ahc1: Primary High Byte termination Enabled
ahc1: Downloading Sequencer Program... 419 instructions downloaded
device_probe_and_attach: ahc1 attach returned 12
ahc1: <Adaptec aic7899 Ultra160 SCSI adapter> port 0x1800-0x18ff mem =
0xe8001000-0xe8001fff irq 5 at device 13.0 on pci0
ahc1: Reading SEEPROM...done.
ahc1: Manual SE Termination
ahc1: Manual LVD Termination
ahc1: BIOS eeprom is present
ahc1: Primary Low Byte termination Enabled
ahc1: Primary High Byte termination Enabled
ahc1: Downloading Sequencer Program... 419 instructions downloaded
device_probe_and_attach: ahc1 attach returned 12
ahc1: <Adaptec aic7899 Ultra160 SCSI adapter> port 0x1800-0x18ff mem =
0xe8001000-0xe8001fff irq 5 at device 13.0 on pci0
ahc1: Reading SEEPROM...done.
ahc1: Manual SE Termination
ahc1: Manual LVD Termination
ahc1: BIOS eeprom is present
ahc1: Primary Low Byte termination Enabled
ahc1: Primary High Byte termination Enabled
ahc1: Downloading Sequencer Program... 419 instructions downloaded
device_probe_and_attach: ahc1 attach returned 12
ahc1: <Adaptec aic7899 Ultra160 SCSI adapter> port 0x1800-0x18ff mem =
0xe8001000-0xe8001fff irq 5 at device 13.0 on pci0
ahc1: Reading SEEPROM...done.
ahc1: Manual SE Termination
ahc1: Manual LVD Termination
ahc1: BIOS eeprom is present
ahc1: Primary Low Byte termination Enabled
ahc1: Primary High Byte termination Enabled
ahc1: Downloading Sequencer Program... 419 instructions downloaded
device_probe_and_attach: ahc1 attach returned 12
xl0: <3Com 3c980C Fast Etherlink XL> port 0x2000-0x207f mem =
0xe8003400-0xe800347f irq 7 at device 15.0 on pci0
xl0: Ethernet address: 00:e0:81:04:ed:bc
xl0: media options word: a
xl0: found MII/AUTO
bpf: xl0 attached
xl1: <3Com 3c980C Fast Etherlink XL> port 0x2080-0x20ff mem =
0xe8003800-0xe800387f irq 11 at device 16.0 on pci0
xl1: Ethernet address: 00:e0:81:04:ed:bd
xl1: media options word: a
xl1: found MII/AUTO
bpf: xl1 attached
miibus0: <MII bus> on xl0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0: OUI 0x00105a, model 0x0000, rev. 0
ukphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
miibus1: <MII bus> on xl1
ukphy1: <Generic IEEE 802.3u media interface> on miibus1
ukphy1: OUI 0x00105a, model 0x0000, rev. 0
ukphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ad0s1: type 0x83, start 63, end =3D 530144, size 530082 : OK
ad0s2: type 0x7, start 530145, end =3D 21511034, size 20980890 : OK
ad0s3: type 0x85, start 21511035, end =3D 156296384, size 134785350 : OK
ad0s1: type 0x83, start 63, end =3D 530144, size 530082 : OK
ad0s2: type 0x7, start 530145, end =3D 21511034, size 20980890 : OK
ad0s3: type 0x85, start 21511035, end =3D 156296384, size 134785350 : OK
ad0s1: type 0x83, start 63, end =3D 530144, size 530082 : OK
ad0s2: type 0x7, start 530145, end =3D 21511034, size 20980890 : OK
ad0s3: type 0x85, start 21511035, end =3D 156296384, size 134785350 : OK
ad0s1: type 0x83, start 63, end =3D 530144, size 530082 : OK
ad0s2: type 0x7, start 530145, end =3D 21511034, size 20980890 : OK
ad0s3: type 0x85, start 21511035, end =3D 156296384, size 134785350 : OK
ad0s1: type 0x83, start 63, end =3D 530144, size 530082 : OK
ad0s2: type 0x7, start 530145, end =3D 21511034, size 20980890 : OK
ad0s3: type 0x85, start 21511035, end =3D 156296384, size 134785350 : OK
ad0s1: type 0x83, start 63, end =3D 530144, size 530082 : OK
ad0s2: type 0x7, start 530145, end =3D 21511034, size 20980890 : OK
ad0s3: type 0x85, start 21511035, end =3D 156296384, size 134785350 : OK
ad0s1: type 0x83, start 63, end =3D 530144, size 530082 : OK
ad0s2: type 0x7, start 530145, end =3D 21511034, size 20980890 : OK
ad0s3: type 0x85, start 21511035, end =3D 156296384, size 134785350 : OK
ad0s1: type 0x83, start 63, end =3D 530144, size 530082 : OK
ad0s2: type 0x7, start 530145, end =3D 21511034, size 20980890 : OK
ad0s3: type 0x85, start 21511035, end =3D 156296384, size 134785350 : OK
fd0: autoselection failed
fd0: autoselection failed
ad0s1: type 0x83, start 63, end =3D 530144, size 530082 : OK
ad0s2: type 0x7, start 530145, end =3D 21511034, size 20980890 : OK
ad0s3: type 0x85, start 21511035, end =3D 156296384, size 134785350 : OK
dscheck(cd0): bio_bcount 512 is not on a sector boundary (ssize 2048)
dscheck(cd0): bio_bcount 1024 is not on a sector boundary (ssize 2048)
(ahc0:A:5:0): Sending SDTR period 19, offset f
(ahc0:A:5:0): Received SDTR period 19, offset f
	Filtered to period 19, offset f
(cd0:ahc0:0:5:0): Retrying Command

------=_NextPart_000_000B_01C1E4E9.0D1509C0--


To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-scsi" in the body of the message




Want to link to this message? Use this URL: <http://docs.FreeBSD.org/cgi/mid.cgi?!~!UENERkVCMDkAAQACAAAAAAAAAAAAAAAAABgAAAAAAAAAjQHXypTRWUeX0Da3WGxUUMKAAAAQAAAAB5S/GF2FpEylB6XRir51UAEAAAAA>